We use cookies and similar tools for site analytics and advertising. See our Privacy Policy for details. Do Not Sell or Share My Personal Information
Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
This is a factory switch used in the appliance's control/safety circuit. Replacing a worn or failed switch restores reliable signaling so the selected function engages properly and the unit responds consistently to user inputs and status conditions.
I removed two sheet metal screws to remove the panel above the washing machine lid. That exposed four more phillips drive sheet metal screws, after removing those the dashboard control panel is held by two smaller black screws slightly recessed in the lower corners. This allowed the panel to be pulled down from the top, revealing the back of the switch. At this point I took a picture of the wiring connections with my cell phone to make sure I put them on the new switch in the same... Read more
Replacement suspension spring for washer tub support systems. Restores proper tension when original spring is weakened, broken, or causing tub tilt.
Watched a few of your videos and ordered the springs and a insert, and actually got the parts right. I am not a Appliance repair guy but I am retired and I am pretty handy so I thought what the heck. I watched the videos, a lot of common sense, common tools, and plenty of time. My knuckles are busted up and a little blood, but I got it done. Was actually kind of rewarding. Works like a champ. The Videos, ARE AWESOME. Read more
This replacement bolt secures internal components in your appliance. A stripped, rusted, or missing bolt can let parts loosen and vibrate; installing a new bolt restores a tight, stable connection for reliable operation.
The seal at the bottom of the tub had started to fail. On large loads water would leak so I ordered a new one rubber seal. Getting the trunnion off the transmission shaft was hard as it was calcified and corroded. I used a wire brush to get some of it off and then used a lot of WD-40. The bolt holding the trunnion plate on sheared off when I tried to remove it on one side and the other came out ok (the bolt hole through the trunnion is not threaded so it should slide out once the plate is off... Read more
This is a 31-inch plastic tube that serves as a protective sleeve for the temperature sensor inside the refrigerator compartment. It houses and shields the sensor probe, helping ensure accurate temperature readings. Replace this tube if it is cracked, broken, or damaged, which can lead to inaccurate temperature regulation and inconsistent cooling.
This factory screw secures panels, brackets, and other components in your cooking appliance. Replace a missing, stripped, or corroded fastener to restore a tight, rattle-free fit and keep parts properly aligned during use.
Bolt replaced. Read more
Outer door glass panel for electric ranges. Replaces cracked, chipped, or shattered glass. Restores visibility and protects internal components.
Ordered new one. Read more
Fix floor puddles and musty odors caused by a cracked defrost drain pan. This pan collects defrost water and allows it to evaporate. Easy DIY fix.
Chewed up plastic parts. All the parts that I received were correct and was easy to install Read more
Refrigerator not cooling properly or running warm? A failing condenser fan motor prevents proper heat removal. This direct-fit motor restores cooling.
1) disconnected motor from electrical supply. 2) undid housing brackets with a socket wrench. 3) undid two screws to remove motor and fan from housing. 4) pried fan off motor. 5) placed fan onto new motor. 6) put fan and motor back into housing. 6) put housing back with two screws from step two. 7) reconnected electrical supply from step one. Read more
This safety thermostat is a temperature-sensitive switch that helps protect your appliance from overheating. When excessive heat is detected, it opens the circuit to stop power to critical components, helping prevent damage and ensuring safe operation.
Aluminum strap secures the defrost heater against the evaporator coil. Replace if broken, cracked, or missing to maintain proper heater contact.
Removed the freezer shelves and back panel, evaporator coils were frozen with ice. Defrosted coil and removed defrost heater connectors, measured no continuity in the heater and ordered a replacement. Also discovered the aluminum retention strap was broken and the heater had slipped down in it's position, ordered and replacement strap. Re-installed new heater and strap per the video instructions, repair complete. Most difficult steps were drilling out the drain pan rivet and re-threading... Read more
Secures moving components and provides a stable pivot surface in your refrigerator. Replace when worn, broken, or causing looseness and poor alignment.
Replace the part Read more
Color: White
Using the make and model of the refrigerator, I did some research on the internet to find a detailed diagram of the door. I then found AppliancePartsPros.com. Since the diagram was somewhat difficult to see clearly, the representative I spoke with on the phone went the extra mile to be sure I ordered the correct parts. Read more
Fix E32 error codes or washer stopping during fill with this water level pressure switch. Senses water level and controls fill cycles. DIY-friendly repair.
The E32 diagnostic code that the Frigidaire washer was throwing after a quick water fill attempt was not in the supplied Data Sheet that came with the washer and Frigidaire would not provide and updated Data Sheet because, "it's a liabiliity issue" was their statement, but they did tell me that the problem was in the Fill Pressure Sensor/Wire Harness or the Main Control Board (the display board). I ordered the Pressure Sensor and Main Control Board from AppliancePartsPros after checking... Read more
Screw that adjusts and secures the leveling leg to your range base or bracket. Replace if stripped, bent, or missing to restore stable footing and level your appliance.
I placed the burner cap on the burner and screwed in the leveling leg. Easy! Read more
Burner not heating or burned out? This surface heating element restores your cooktop. DIY-friendly repair with online video guides available.
Replaced with a new element from AppliancePartsPros.com. Ordered online. Read more
This replacement screw secures appliance panels and components. With a #10-16 thread and 0.75-inch length, it replaces stripped, rusted, or missing hardware to restore a tight, rattle-free fit and reduce vibration and noise.
Googled the problem, watched videos on Youtube. Took apart machine and tried cleaning filter most people said was the problem. Wasn't anything but a penny in it so that wasn't the problem. I decided the pump must be bad ,the spring for the bellows and the console were broken so I bought those as well. Got the parts put them on and machine filled up with water turned over a few times and then stopped. The only thing else it could be is the fill level sensor or the main circuit board. Ordered... Read more