Cfcp1rkbd Ss Parts

• Fridge too cold
• Too warm
• Fridge runs too long
• Freezer too cold

I unplugged the fridge and took all the food and shelving out of the freezer and then proceeded to take off the bottom sliding drawer rack on both sides off (4 Phillips head screws). Then took off the light bulb cover and then the light bulb. Then the back wall that covers the coils and tubes that the refrigerant runs through ( 2 screws with hex head). After sliding out the back wall I could see that the entire coil area was frosted and iced up. I took a blow dryer and melted all of it over... Read more

I seared the web and found Appliance Parts Pros site and when I input my GE refrigerator model number I was able to do some diagnostics on their site. It was indicated from my research that the Water Inlet valve most likely was at fault for my problems. I ordered the replacement valve from them and they shipped the same day as the order and it arrived the next day, faster than I had expected. I viewed their video and it was very good at explaining what I had to do to replace the valve on my... Read more

• Ice maker dispenses too little ice
• Not dispensing water
• Ice maker won't dispense ice
• Ice maker not making ice

By visiting your website, viewing the repair instructions and ordering the right parts. Very easy to understand and to do the repair.. Read more

• Ice maker won't dispense ice
• Door sweating
• Frost buildup

My refrigerator is 13 yrs old and began to build up frost in the ice cube shoot and the water tube began to freeze up over night. The flapper door was not closing completely. I simply removed the control panel by pulling up and out on the bottom edge, the edge is only about 1/8 inch thick, so don't reach in to far. You should be able to feel a small division line between the control panel and the refrigerator. No screw driver was needed to expose the 4 mounting screws of the inner dispenser... Read more

• Leaking
• Not dispensing water

We noticed a puddle of water in front of the fridge a couple of months ago-dried the floor up both times and thought someone had dropped ice-or spilled water. A couple of weeks ago there was water dripping through the dropped tile ceiling in the basement. I shut off the water for the water supply to the fridge at the copper pipe in the basement and removed some of the tiles which felt a little damp. It still dripped all day. When my spouse came home he pulled down more of the tiles. It was as... Read more

I ordered a new switch from APP and fixed my fridge. However, the video posted for this repair on this site is not applicable to newer refrigerator models. I have a 2015 GE GTE18IHCRSS and had to drop the control housing (#432 in the diagram) to attach the wire/plug assembly to the switch. Only had to remove the front screw with a 1/4" nut driver and that provided enough of a gap for me to plug in the switch. So the correct method to replace the light switch in a newer model refrigerator is as... Read more

I have an 11 year old GE Monogram side by side built-in fridge that had been having cooling problems intermittently. The fridge would work for a day and then the compressor would not come on for 8 hours and temps would rise to the upper 20s in the freezer. Fans, lights, and everything else appeared to be functioning properly. It went like this for a few weeks and we put it off until the compressor decided not to come on at all for a full day. Being barely able to use a multi-meter, I watched a... Read more

• Freezer section too warm

New cond fan & new evap fan & new defrost heater unit Read more

After disconnecting power to the fridge, I first removed the ice maker/water dispenser/fridge control faceplate. This easily popped out using a flat head screw driver. Then disconnected the 3 wire harness connections to the control board. I next removed the plastic dispenser housing shield. There's only 4 screws that hold this on. Finally, I removed the Micro-switch, disconnected the two wire connectors and installed the replacement switch and reinstalled everything. The repair took only... Read more

The repair went great with the guidance from your website and the parts that we purchased! also the video was great! Read more

My refrigerator is 13 yrs old and began to build up frost in the ice cube shoot and the water tube began to freeze up over night. The flapper door was not closing completely. I simply removed the control panel by pulling up and out on the bottom edge, the edge is only about 1/8 inch thick, so don't reach in to far. You should be able to feel a small division line between the control panel and the refrigerator. No screw driver was needed to expose the 4 mounting screws of the inner dispenser... Read more

• Fridge too warm

Replacement of the evaporator fan motor, fan blade, and grommets. The amount of disassembly to reach the part took most of the effort Read more

Replacement of the evaporator fan motor, fan blade, and grommets. The amount of disassembly to reach the part took most of the effort Read more

Condenser fan stopped on my big 2003 Monogram 4 foot wide ZIS480D Refrigerator. It is top mounted. The fridge had to be rolled out. 20 screws removed and the top sheet metal to get at the condenser. That was the only way to get at it. Works like new now. Read more

I had found that the fan in the freezer was making a lot of noise. Turns out the shaft was loose, causing the flan blade to wobble. Replaced the motor and fan and now it runs like a new unit. Read more

Changed fan motor, rubber grommets, and dust cover. It sounded like the vibrating sound was being caused by the motor. But, come to find out I had a chipped blade on one of the fan blades. So make sure and check the fan blade first. Thanks Appliance Parts Pros everything for just as it should. Read more