Wdt910ssywd0 Parts

The repair kit has everything needed for both sides of the rack but there were no instructions so it took me some time to figure out how it all mounted on the basket. The original design was totally different than the repair kit so it would have been very beneficial to have at least a diagram that showed how everything fit together. That being said, once I figured out how all the parts fit, then it was a very easy repair. You won't reuse any of the old parts except for the end caps that snap... Read more

I ordered 4 of this part from AppliancePartsPros.com and watched the repair video of the product. This was a simple repair that took 10 minutes to replace all 4 wheel units on the bottom rack. Product is exact match to the part I replaced. Read more

My discharge would not empty after a wash cycle and I always had gross gray water left in the bottom approx 3" deep? After doing the obvious things of checking the simp for garbage, and checking that the discharge hose wasn't blocked, I removed my discharge pump ( not too hard to do) and tested. My pump which did run and turn the impeller. However, the pump evidently had weakened with time and weakened and could no longer pump the waste water up hill to the "T" connection under the sink. A... Read more

I called to ask about the correct gasket for the door. As VERY helpful lady suggested that it was probably a split arm spray. She was absolutely correct. I have used you web site for parts in the past and will always make it my first stop when ordering appliance parts. Read more

Thanks to Jason and his tech people at Appliance Parts Pro, I was able to remove and replace the seal and eliminate all leaks at the bottom of the door. I have a Kitchenaide (Whirlpool) dishwasher model KUDC10IXBL1. Here is how to replace the bottom door seal. 1) Shut off breaker to dishwasher on the electrical panel. 2) Open the dishwasher door completely, and while supporting the door, remove the hex head screws that hold the outside cover. 2) Close the door carefully and slip the outside... Read more

I took the bottom access cover off, and checked underneath the unit to isolate where it was leaking from. Cleaned the cover, and the spot where the leak happened was marked for me. The front, far left hand side, behind the door. Ran a quick rinse cycle with a pan under the spot to verify it was there. It was. Then I did an internet search and found your website. Our dishwasher, bought in November of 2016, was listed, and several of the reviewers said wonderful things about their experiences... Read more

• Noisy
• Door won't close
• Door latch failure

I finally decided to repair my dishwasher because the door would free fall to the floor possibly breaking the hinges. Also the top shelf was rolling out on its own every time the door was opened. I first pulled the dishwasher out of the enclosure and found that the drain hose was directly under the pump area throwing the unit completely out of level. Also the inadequate plastic and rope counterbalance on the left side was completely broken where the rope was attached to the plastic piece to the... Read more

• Will not drain

I've opened sump housing to check for clogging but it was clean. When I removed check valve to inspect it I've found out that the round part of the valve was missing so I figured it might've blocked the water exit at drain hose or something like that. So I pulled the dishwasher out to get a full access to drain hose connector and the pump. Upon disconnecting the drain and checking its connector I indeed found the round piece totally blocking the hose and acting as a seal. I removed the piece... Read more

• Will not fill with water

As mentioned, our Whirlpool Dishwasher would complete the cycle but Tablet pretty much sat in the Soap Dispenser Box nor there was any sign of water inside the Dishwasher. This happened 2 - 3 times. Hence decided to dive into what the fix was. After reviewing a bunch of Youtube Videos, understood first how a typical Dishwasher operates and what are the basic checks it does before water is let inside. So it typically first checks whether Door S/w got activated, followed by Float Switch... Read more

I bumped into my KitchenAid dishwasher and the upper rack adjuster cracked. There was already a crack on the notch of the housing where the handle (lever) sits. In addition, the positioner popped out and I couldn't find it. So, I bought the three parts from AppliancePartsPros online. It arrived in about a week. The repair was fairly simple, but it still took about 45 minutes because I didn't want to crack the assemblies. For the housing, use a small slotted screwdriver to carefully... Read more

Followed the Appliance Parts Pros video and it took me about an hour from start to finish. I felt like the job was easy to accomplish. Read more

Changed the door switch and the dishwasher works now. Read more

My dishwasher was leaking and I called to have a certified technician come to diagnose the problem. I removed the kick panel from the bottom of the machine. He turned it on and we saw that water was leaking from the bottom. He said I needed a Sump kit but it wasn't in stock. The cost was $170 plus tax and labor cost was another $140. So I talked it over with dad and ordered the Sump kit, the hose clamp and a new diverter motor as mine was yellowed with age. The cost of all these parts and... Read more

ORDERED NEW SUMP AND DIVERTER MOTOR, THE SHAFT ON THE DIVERTER MOTOR FELT A LITTLE ROUGH SO I WENT AHEAD AND REPLACED IT, THE SUMP REPLACEMENT WENT FAIRLY EASY. HAD TO MAKE A TRIP TO THE HARDWARE STORE FOR A HOSE CLAMP. ONE HOSE ON THE SUMP HAS A CLAMP THAT IS NOT REUSEABLE. YOU SHOULD ALSO ORDER THIS CLAMP. IT IS NARROW AND A REGULAR HOSE CLAMP WILL NOT WORK. Read more

While this is a Whirlpool dishwasher, I have the Kenmore Elite version of it. I believe them to be identical for parts. A little background: The first symptom I had of problems was plastic bits from the ball bearing retainer strips in the slides falling out. Then ball bearings falling out. A common problem with this dishwasher. When disassembling the upper basket, some of the gray plastic pieces were very brittle and easily snapped off. So I ended up replacing all of the plastic pieces related... Read more

Pulling the dishwasher, it was obvious we had a slow leak under it. We had a slow leak from the diverter motor area in the sump. Sure enough, it looked like the gasket around a shaft had to be the culprit. The gasket was attached to the sump assembly, or the motor. We took a chance and ordered a new sump assembly for a mere $90 and went for it. All of the trays had to come out. The lower spray arms. Then the distribution runs to the middle rack arms and upper rack arms. Finally, the original... Read more