Ade8060 Parts

Restore consistent heat with this 5350-watt dryer heater assembly. Replacing a failed element brings back proper drying temperatures so loads finish on time, using the OEM orange-coded configuration specified for select machines.

• Heats the air in electric drying cycles by energizing the element inside the heater housing
• Common fix for no heat, very long dry times, or lukewarm exhaust air
• Replaces a broken/open heating coil; visible breaks or no continuity indicate failure
• Orange-coded assembly matches the specific OEM configuration—verify against your original or IPL

• Disconnect power and allow the appliance to cool before servicing
• Note wire positions; transfer any thermostats/limit devices from the old assembly if your model uses separate components
• Handle by the frame—avoid touching or deforming the bare heating coil
• After installation, clean lint passages and verify proper vent airflow to prevent premature element failure

The Light Bulb is an OEM part for Whirlpool refrigerators. This part illuminates the water and ice dispenser area, providing visibility and ease of use, especially in low light conditions. 

Over time, the light bulb can fail due to normal wear and tear, electrical surges, or damage from vibrations and impacts. 

Symptoms of a bad light bulb include:

• The dispenser area not lighting up when activated
• Flickering or dim lighting
• The bulb failing to turn on consistently

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This factory fastener secures appliance components such as panels, brackets, and trim. Replacing a missing or stripped screw restores a tight fit, reduces rattling, and helps keep assemblies aligned for reliable performance.

• Fastens appliance parts to maintain structural integrity and alignment
• Helps address symptoms like loose or vibrating panels, gaps, or hardware that won't stay tight
• Replaces lost, damaged, or corroded fasteners during repairs or reassembly
• OEM-matched thread and fit for the specified location

• Disconnect power; shut off gas or water supplies before servicing
• Replace one screw at a time to preserve alignment of parts
• Start threads by hand to avoid cross-threading; tighten snugly without over-torquing
• Use the correct driver size/type specified for your model

This cycling thermostat regulates exhaust temperature by switching the heater on and off to maintain proper drying heat. Replacing a failed thermostat restores consistent temperatures, helps auto-dry timing, and protects against fabric-damaging overheating.

• Controls the heating circuit to maintain target drying temperatures
• Provides temperature feedback for accurate auto-dry operation
• Common symptoms: long dry times, very hot drum/cabinet or scorching odors, auto-dry not advancing correctly, or no heat if the thermostat fails open
• Typically mounted on the blower housing to sense exhaust air temperature

• Disconnect power; for gas dryers, also shut off the gas supply
• Access the thermostat (commonly on the blower housing); remove the necessary panel(s)
• Transfer wires one at a time to the new thermostat and mount it flat against the housing
• Reassemble, verify clear venting/airflow, and run a test cycle

The Timer is an OEM part for Whirlpool dryers. It controls the electrical components and the timing of the drying cycles, ensuring clothes are dried according to the selected settings. This timer manages the duration of each cycle, turning the dryer off when the cycle is complete.

Over time, the timer can fail due to wear and tear, electrical malfunctions, or internal component damage.  

Symptoms of a bad timer include:

• The dryer not advancing through cycles
• The dryer running for an unusually long time
• The dryer not turning on or off at the appropriate times
• Irregular or incomplete drying cycles

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Drying Rack is an OEM part for Speed Queen dryers. This part provides a flat, stationary surface within the dryer drum for drying items that should not be tumbled, such as shoes, hats, or delicate garments. 

Common causes of a bad drying rack include physical damage from overloading, warping from exposure to high heat, or cracks and breaks from regular use over time.

Symptoms of a bad drying rack include:

• Items not staying in place during the drying cycle
• Visible cracks, bends, or breaks in the rack
• Difficulty fitting the rack securely in the dryer drum
• Unusual noises during the drying process due to a loose or unstable rack

This OEM Speed Queen part is also compatible with some Alliance Laundry Systems models.

This replacement igniter lights the gas burner in your range or wall oven, restoring reliable starts and consistent heat. Swap in a fresh igniter to resolve hard-to-light burners and no-heat situations so cooking cycles begin as they should. What it does:

• Provides the ignition source to light the bake or broil burner flame
• Helps ensure fast, consistent burner light-off at the start of a heat cycle
• Common symptoms of failure: no ignition/no heat, delayed or intermittent ignition, repeated clicking without flame, or a gas odor before light-off

• 1 igniter assembly

• Disconnect power and shut off the gas supply before servicing; allow the appliance to cool completely
• Note wire connections and mounting orientation from the original part for correct reassembly
• Handle the ceramic/element carefully to avoid damage
• After installation, restore gas and power, then check for leaks with a soap solution

This lint filter traps lint and fibers as air moves through the dryer, helping maintain proper airflow and drying performance. Replace a damaged or missing screen to reduce lint buildup inside the machine and along the vent.

• Captures lint and debris during the drying cycle to protect the blower and venting
• Helps maintain airflow for consistent drying results and temperature control
• Reduces lint redepositing on clothes and around the door opening
• Replace if the mesh is torn, the frame is warped/cracked, or if you notice longer dry times or excess lint inside the drum

• Disconnect power before servicing
• Remove the old screen and vacuum out the lint chute/housing; inspect and clean the exhaust vent as needed
• Insert the new filter and ensure it seats fully and flush—do not operate the dryer without the filter in place
• Run a short test cycle to confirm proper airflow at the exhaust

This push button switch mounts in the appliance's control panel and sends an electrical signal to the control when pressed. Replace a worn or sticking switch to restore dependable button response and function activation. What it does:

• Panel-mounted switch that closes its contacts when pressed to signal the control
• Restores reliable front-panel input for starting or selecting a function
• Helps address no response or intermittent response when the button is pressed
• Replaces switches with loose action, sticking, or heat-discolored/burned terminals

• 1 push button switch

• Disconnect power before servicing to avoid electrical shock
• Access the console/control panel to reach the switch
• Note wire positions (take a photo) and transfer connectors one at a time; ensure firm, fully seated terminals
• Secure the switch in the panel (nut/clip as applicable), verify button action, then reassemble and test

This 3-position fabric selector switch is the control behind the knob that lets you choose the fabric setting on your unit. Replacing a worn switch restores positive detents and ensures your selection is recognized instead of ignored or stuck.

• Provides three selectable fabric settings to tailor operation
• Routes the chosen setting to the timer/control
• Typical symptoms: no response when changing settings, intermittent selection, or being stuck on one mode
• Physical clues of failure: loose/no detent feel, broken shaft, or heat-discolored terminals

• Disconnect power before servicing
• Access the control console; remove the knob and retaining hardware to free the old switch
• Photograph/label wire positions and transfer each lead to the same terminals on the new switch
• Reassemble and test all three positions for proper engagement

This motor pulley transfers power from the drive motor to the washer belts. The 60 Hz sizing restores the correct speed and belt tracking so the tub agitates and spins smoothly without squeal or slippage. What it does:

• Drives the belt(s) that power the washer's drive system (and on some models, the drain pump)
• Maintains the correct speed ratio for 60 Hz operation
• Worn or damaged pulley can cause belt squeal, burning rubber odor, or frayed/slipping belts
• Result in no/slow spin or agitation if the belt can't grip properly

• One motor pulley (60 Hz)

• Disconnect power before servicing; wear cut-resistant gloves
• Access the motor, relieve belt tension, and note belt routing
• Loosen the pulley set screw and remove the old pulley from the motor shaft
• Install and align the new pulley; adjust belt alignment/tension per service information, hand-rotate to check clearance, then test

• Designed for 60 Hz electrical systems; match the Hz rating to your original part

The Thermal Fuse is an OEM part for Whirlpool dryers. This part prevents the dryer from overheating by cutting off power to the heating element if the dryer exceeds a safe temperature. It helps protect the appliance and home from potential fire hazards caused by overheating.

Causes of a bad thermal fuse can include lint buildup restricting airflow, a malfunctioning thermostat, or excessive load causing the dryer to overheat.  

Symptoms of a bad thermal fuse include:

• Dryer not starting
• Dryer not producing heat
• Dryer shutting off mid-cycle
• No power to the dryer despite other electrical components functioning

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

10 - 16 x 1/2

This lint filter captures lint and fibers from the drying airflow to protect the blower and vent path. Replacing a damaged or missing screen helps maintain airflow, reduce lint buildup, and keep drying performance consistent.

• Traps lint and debris as air circulates through the dryer
• Helps maintain proper airflow and drying efficiency
• Replace if mesh is torn, frame is warped/cracked, or the filter won't seat fully
• Common symptoms: longer dry times, lint on clothes or around the door, or a filter that pops out

• Disconnect power; for gas models, also shut off the gas supply
• Remove the old filter from the lint opening and vacuum any lint from the housing
• Insert the new filter fully so it sits flat and seals properly
• Never operate the dryer without the lint filter installed

Specs: 10-16 x 1/2 inch.

Size: 8 x 1/2 ab.