Adee9rgs175w01 Parts

Dryer lint filter traps fibers to maintain airflow and drying efficiency. Replace if torn, damaged, or missing to prevent lint buildup. Confirm fit.

This seal kit includes felt seals designed for use in residential dryers manufactured from 1992 onward. The felt seals sit between the drum and the dryer housing to prevent heated air and lint from escaping the drum cavity. Replace this kit if you notice excessive lint buildup outside the drum area, longer drying times, or unusual squeaking and scraping noises during operation.

Flat stationary rack that installs inside the dryer drum for air-drying shoes, hats, and delicate garments without tumbling. Replace if cracked or broken.

White plastic cover that snaps over the lint screen opening. Replace if cracked, broken, or missing to protect laundry from falling into the compartment.

Fix a dryer door that won't stay closed or pops open during cycles. This metal door strike secures the door and engages the safety switch. Easy DIY repair.

Protective plate covering the rear outlet vent on your dryer. Replace if cracked, broken, or missing to prevent objects from entering the vent area.

Clothes not drying or taking too long? This dryer blower wheel circulates air through the drum to dry clothes efficiently. Mounts on motor shaft.

Covers the lint screen opening and directs airflow for efficient lint capture. Replace if cracked or missing to maintain proper airflow and prevent snags.

Dryer not powering on or overheating at the power connection? This terminal block assembly restores safe electrical connections. Moderate DIY repair.

This replacement moisture sensor bar mounts inside the drum and helps the dryer detect when laundry is dry. A worn or damaged bar can cause sensor-dry cycles to end too soon or run too long.

• Senses moisture on fabrics and signals the control to advance or extend auto-dry cycles
• Helps stop the cycle when clothes reach the selected dryness level
• Symptoms can include auto-dry cycles ending early, extended run times, or inconsistent dryness
• Build-up on the bars can also affect sensing performance

• Disconnect power before servicing; shut off gas supply for gas dryers
• Access the sensor at the front bulkhead/lint housing; move wire leads to the new bar and secure with existing hardware
• Clean any residue from both sensor bars to improve accuracy
• Reassemble and test with a small damp load on a sensor cycle

This Outer Tub Gasket seals the outer tub assembly in your washer to keep wash water contained through every cycle. Replacing a flattened, cracked, or leaking gasket helps stop water on the floor and protects internal parts.

• Creates a watertight seal between outer tub components
• Helps prevent leaks during fill, wash, and spin
• Common symptoms: water under the washer; moisture at the tub seam; visible cracks or compression set on the gasket
• Restores proper sealing after service or disassembly

• Disconnect power and water supplies; move the washer for safe access
• Access the outer-tub seam per your model's service procedure; note gasket orientation
• Remove the old gasket and clean mating surfaces; install the new gasket evenly without twists or gaps
• Reassemble and run a brief test cycle to check for leaks

Seals the gap between drum and bulkhead to reduce air leaks, prevent lint buildup, and quiet operation. Replace if torn or worn. Adhesive required.

Rotating drum assembly that tumbles laundry during drying. Replace if dented, rusted, or causing noise and uneven drying. Confirm fit with your model.

This dryer output control kit replaces the dryer's output-control assembly to restore correct electronic signaling and normal cycle operation. Use it to address intermittent starts, unexpected stops, or cycles that end prematurely. What it does:

• Replaces the dryer's output-control assembly to restore proper output signaling between components.
• Helps correct intermittent operation, failure to start, unexpected shutdowns, or incorrect cycle termination.
• Restores worn or damaged control hardware so the dryer can complete selected cycles.

• Disconnect electrical power (and turn off gas supply for gas dryers) before beginning any work.
• Handle electronic components carefully and avoid static discharge; do not force connectors.
• Follow OEM wiring and mounting orientation exactly; tight mounting prevents misalignment and noise.

Secures and protects your dryer's interior light for clear drum visibility. Replace if cracked, loose, or light fails. Verify fit with your model number.

Fix a dryer that won't detect fabric dampness or stop at the right time. This moisture sensor base secures sensing contacts for accurate cycle timing.