Adg3lrs111tw01 Parts

This 3-position fabric selector switch is the control behind the knob that lets you choose the fabric setting on your unit. Replacing a worn switch restores positive detents and ensures your selection is recognized instead of ignored or stuck.

• Provides three selectable fabric settings to tailor operation
• Routes the chosen setting to the timer/control
• Typical symptoms: no response when changing settings, intermittent selection, or being stuck on one mode
• Physical clues of failure: loose/no detent feel, broken shaft, or heat-discolored terminals

• Disconnect power before servicing
• Access the control console; remove the knob and retaining hardware to free the old switch
• Photograph/label wire positions and transfer each lead to the same terminals on the new switch
• Reassemble and test all three positions for proper engagement

Fix a dryer door that won't stay closed or pops open during cycles. This metal door strike secures the door and engages the safety switch. Easy DIY repair.

Flat stationary rack that installs inside the dryer drum for air-drying shoes, hats, and delicate garments without tumbling. Replace if cracked or broken.

Clothes not drying or taking too long? This dryer blower wheel circulates air through the drum to dry clothes efficiently. Mounts on motor shaft.

Dryer not powering on or overheating at the power connection? This terminal block assembly restores safe electrical connections. Moderate DIY repair.

This sensor monitors operating conditions and relays accurate feedback to the control so cycles run properly. Replacing a failed sensor helps restore correct operation and prevent erratic behavior or fault codes. What it does:

• Detects a specific operating condition and sends a signal to the control
• Helps the machine regulate cycle timing and performance
• Can cause error codes, cycles that won't start or advance, or intermittent shutdowns when failing
• Lead to inconsistent temperatures or sensing behavior depending on application

• 1 sensor

• Disconnect power (and shut off gas/water, if applicable) before servicing
• Access the sensor; note wire positions and connector orientation
• Install the new sensor in the same location and orientation; seat connectors fully
• Clear any stored faults and run a test cycle per the tech sheet

Fixes long dry times and temperature issues. This dryer thermostat regulates heat cycling to prevent overheating or underheating. Simple repair.

Seals the gap between drum and bulkhead to reduce air leaks, prevent lint buildup, and quiet operation. Replace if torn or worn. Adhesive required.

This Outer Tub Gasket seals the outer tub assembly in your washer to keep wash water contained through every cycle. Replacing a flattened, cracked, or leaking gasket helps stop water on the floor and protects internal parts.

• Creates a watertight seal between outer tub components
• Helps prevent leaks during fill, wash, and spin
• Common symptoms: water under the washer; moisture at the tub seam; visible cracks or compression set on the gasket
• Restores proper sealing after service or disassembly

• Disconnect power and water supplies; move the washer for safe access
• Access the outer-tub seam per your model's service procedure; note gasket orientation
• Remove the old gasket and clean mating surfaces; install the new gasket evenly without twists or gaps
• Reassemble and run a brief test cycle to check for leaks

Rotating drum assembly that tumbles laundry during drying. Replace if dented, rusted, or causing noise and uneven drying. Confirm fit with your model.

Fix a dryer that won't start due to door latch issues with this door strike bracket. Restores proper door alignment so your machine recognizes a closed door.

Supports the front edge of your dryer drum for smooth, quiet rotation. Replace when you hear scraping or squealing sounds. Verify fit with your model.

Secures and protects your dryer's interior light for clear drum visibility. Replace if cracked, loose, or light fails. Verify fit with your model number.

Seals the blower housing to direct airflow through the drum and exhaust. Replace when worn to restore drying performance and prevent lint leakage.

Threaded metal shaft that mounts the idler roller in dryers and washer-dryer combos. Replace if bent, worn, or stripped threads prevent secure roller installation.

Replaces missing or damaged 10B-16 x 0.34 inch cabinet screw. Secures panels, brackets, and covers. Restores tight fit to reduce vibration and rattles.