Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Burner won't light or igniter keeps clicking? This cooktop igniter creates the spark to ignite gas burners. DIY repair. Video guide available.
My 18+ year old Jennair cooktop, PN CCG2520W was in need of a rebuild b/c of a welded venturi tube on the right front [RF] burner. In order to remove the glass top cover, you MUST remove the venturi tube. To do this you have to DRILL-OUT the venturi tube which requires a new venturi and orifice holder. The repair was difficult b/c most of the parts are no longer available. But then I found a ray-of-hope. I was able to find some Jennair (Maytag) parts but they are scarce. Later I found... Read more
Secures the igniter to your cooktop for proper alignment and stable ignition. Replace if igniters are loose or spark inconsistently. Confirm fit.
Symptoms: would not light & no gas smell/flow. R&R'd gas solenoid which fixed it. Other parts were in addition to primary inop burner. Read more
Fixes burners that won't ignite or spark continuously. This spark module generates the high-voltage needed for gas ignition. DIY repair, 1-2 hours.
Bought a Thermador PRSE48" dual fuel range from Craigslist really cheap because it didn't work. Did a little research and decided to overhaul most of the top (gas) end. For what I paid for it it was worth it and I'd have a good stove with new components. Replaced the griddle thermostat, ignition micro switches, ignition re-igniter box, installed fixing kit with 2 new potentiometers, both solenoids, and gas regulator. Had to replace 2 gas lines, all 4 jets, and one brass nut that were... Read more
Brass nut secures the jet holder assembly on gas ranges and cooktops. Replace if stripped, corroded, or damaged during burner maintenance or repair.
First and foremost, don't believe everything you see on Youtube. In order to get to the gas solenoid that feeds the burner you MUST take the entire top off that side of the range. Remove the grates and burner tops. You will see 2x 20mm brass nut, or so it appears, that hold each burner in place on the splash/drip pan. It is not just a nut, it is a venturi that threads down into what is called the jet holder. You may get a socket on it and think you are getting it loose but, more than likely you... Read more
Fix a downdraft vent that won't go up or down, or cycles on its own. This range hood switch controls vent movement. DIY repair in about 1 hour.
I replaced the switch Read more
Burner won't light or has no gas flow? This top burner valve controls gas to individual burners. Moderate DIY repair with basic tools needed.
Seals between burner and cooktop surface to prevent gas leaks. Replace if cracked, worn, or causing ignition issues. Verify fit with your model number.
I ordered a replacement gas solenoid valve, which arrived the very next day with only standard shipping! The shipped part was exactly what was needed, and I also ordered 4 replacement O-rings to replace the original dried out ring for each burner base. These parts also arrived within a few days and were the exact parts needed. The service and advice received was commendable. Thanks for the great job. Read more
Burner won't spark or ignite? This spark switch signals the ignition module to light gas burners. Common DIY repair with basic tools, 15-30 minutes.
Took out igniter module and porcelain was cracked. Replaced with ordered part and it worker fine! Read more
Replaces broken or non-responsive vent control button on downdraft ranges. Installs on countertop to operate vent up/down position. Includes switch assembly.
Found replacing the switch to be doable, but it was quite a delicate operation. This was for a Thermador range with a broken downdraft switch. It required the removal of 5 small screws which could easily be fumbled and dropped down where it would be difficult, if not impossible to retrieve. Two of the screws were facing the back, so it was a blind operation to remove and replace the screws. Required an offset screwdriver, as space was tight. So, be EXTREMELY careful to not drop the screws and... Read more
Captures grease and cooking vapors to keep air fresh and prevent buildup. Replace when clogged or discolored. Verify fit by model number and dimensions.
I ordered replacement filters--the filters fit inside the vent. I did not have a part number, just the model and the size. These fit great! My down draft was installed in 1996, so I was afraid the part might not be available. Success! Read more
Supplies air to the burner for proper gas combustion. Replace if cracked, seized, or corroded from heat exposure. Installs between valve and burner.
Replaced potentiometers, simmer control unit, and 2 solenoids. Could have been a fairly easy project, except 1 of the venturi's had "seized" preventing even the removal of the range top. After attempting to use an "easy out", which failed, I had to drill out the brass venturi, destroying it, and the jet assembly below. Once the range top was removed, the rest of the repair went well. Took photo's of all the wiring connections to ensure I put it back together correctly. All burners are back... Read more
Black control knob for electric ranges and cooktops. Replaces cracked, broken, or missing knobs. Installs on burner control dial stem for precise heat adjustment.
I searched for the part online and was fortunate enough to find it on your website. Read more
Oven won't heat or shuts off during use? This thermal fuse cuts power when temperature exceeds safe limits. Moderate DIY repair with multimeter testing.
Jet holder with nut for gas cooktops and ranges. Holds the orifice that controls gas flow to each burner. Replace if cracked, corroded, or damaged.
REMOVE THE TOP COVER OF THE STOVE. THE VENTURI NUTS WERE FROZEN.WITH THE JET HOLDER I HAVE TO CUT OR DRILL OUT THE VENTURI NUTS TO RELEASE THE STOVE COVER. IN DOING SO THE JET HOLDERS WERE ROTATED RELATIVE TO THE MOUNTING BRACKET, AS A RESULT, THE TWO TUBING ASSEMBLIES WERE BROKEN. I ONLY FOUND ONE TUBING ASSEMBLY ON LINE. THE OTHER ONE I HAVE TO ABRICATE WITH 1/4" COPPER TUBING, COMPRESSION COLLARS AND WITH THE TWO NUTS SALVAGED FROM THE BROKEN PARTS Read more
Gas burners won't ignite or spark continuously? This spark module generates the high-voltage spark needed to light burners. DIY repair in 30-60 minutes.
I called AppliancePartsPros.com and, with the able assistance of their call taker, was quickly able to determine that the spark module had failed and they had a replacement in stock and it would be immediately shipped to me. It left Oklahoma City that day, via Fed Ex Ground, and was delivered the next day to my location north of Houston. That was excellent service and I will continue to use AppliancePartsPros.com for any future appliance repair needs. Read more
Jet holder assembly routes gas through the orifice to the burner. Replace if cracked, corroded, or stripped threads prevent secure installation.