Asd262ohrb Parts

The Crisper Frame Support is an OEM part for Whirlpool refrigerators. This part provides structural integrity and support for the crisper drawer, ensuring it remains stable and functions smoothly. 

Causes of a bad crisper frame support can include regular wear and tear from frequent use, accidental impacts, or overloading the crisper drawer. 

Symptoms of a bad crisper frame support include:

• The crisper drawer not sliding in and out easily
• Misalignment or instability of the crisper drawer
• Visible cracks or breaks in the frame support
• Difficulty in opening or closing the crisper drawer

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This refrigerator defrost thermostat senses evaporator temperature and controls power to the defrost heater. It melts frost when needed and shuts the heater off at a safe temperature to protect components and keep cooling performance steady.

• Monitors coil temperature and opens/closes the defrost heater circuit
• Terminates the defrost cycle at a safe cutoff to prevent overheating
• Helps keep the evaporator clear of ice so air can circulate
• Common symptoms: heavy frost on the freezer back wall/evaporator, warm refrigerator section, fan noise from ice, long run times with little or no defrosting

• Disconnect power before service; use cut-resistant gloves
• Access the evaporator behind the freezer rear panel and fully thaw any ice using heat-safe methods—never chip or pry
• Reinstall the thermostat in the original location with firm metal-to-metal contact on the evaporator; route and secure wiring as originally
• After reassembly, verify defrost operation and confirm unobstructed airflow

The Water Line Union is an OEM part for Whirlpool refrigerators. It connects sections of the water line, ensuring a secure and leak-proof connection that facilitates the proper flow of water to the ice maker and water dispenser.

Causes of a bad water line union can include wear and tear from prolonged use, exposure to fluctuating temperatures, or physical damage from handling.

Symptoms of a bad water line union include:

• Leaks or water pooling around the refrigerator
• Reduced water flow to the dispenser or ice maker
• Water line disconnections
• Visible cracks or damage on the union

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This crisper drawer cover frame forms the shelf above the produce bins and supports the glass insert. Replacing a damaged frame restores a level surface and smooth crisper drawer operation in your refrigerator.

• Supports the crisper glass and creates the shelf over the produce bins
• Provides the ledges/tracks that allow crisper drawers to slide properly
• Helps contain minor spills and keep the fresh food section organized
• Replace if cracked, warped, or broken; symptoms include a sagging shelf, sticking/misaligned drawers, or glass that won't sit flat

• Disconnect power and remove items from the crisper area before starting
• Carefully remove and set aside the glass insert before lifting out the frame
• Transfer any reusable trim or hardware from the old frame if applicable
• Seat the new frame evenly, then reinstall the glass and drawers

The Handle Clip is an OEM part for Whirlpool refrigerators, specifically designed to secure the refrigerator or freezer door handle to the door. This small but crucial component ensures that the handle is firmly attached, providing a safe and reliable grip for opening and closing the refrigerator.

Causes of these symptoms can range from normal wear and tear, to excessive force applied to the handle, or even material fatigue over time.

Symptoms of a bad Handle Clip include:

• Loose door handle, which may wobble or detach partially from the door
• Difficulty in opening or closing the refrigerator door due to a compromised handle grip
• Visible damage or breakage of the clip, preventing secure attachment of the handle

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This end cap fits on the front of the ice-bin auger. It secures the auger shaft and blade stack inside the ice container so cubes or crushed ice dispense smoothly and the auger stays properly aligned.

• Secures the front of the auger and blades in the ice bucket
• Maintains auger alignment with the drive for reliable ice dispensing
• Helps prevent jams and rattling in the ice container
• Common symptoms of a failed cap: weak/no ice dispense, loose/wobbly auger, grinding or rattling noises, visible cracks or a missing cap

• Disconnect power and remove the ice bin before servicing
• Note the order of blades, spacers, and washers; take a photo for reassembly
• Replace the cap and reassemble in the original order using existing hardware
• Ensure the bin is fully seated and test dispense after restoring power

The Door Switch Assembly is an OEM replacement part for Whirlpool refrigerators. It is responsible for turning the light on when you open the refrigerator door and turning it off when the door is closed. It ensures that the light functions properly, allowing you to easily locate and retrieve items from your refrigerator.

Symptoms of a faulty door light switch include:

• Interior light not turning on when the door is opened
• Interior light staying on even when the door is closed

A bad door light switch can occur due to regular use, wear and tear, or accidental damage. If you notice issues such as the interior light not turning on or off when you open or close the door, it may be time to replace the door light switch.

This Whirlpool replacement part is also compatible with Sears/Kenmore models.
 

The ice auger and crusher blade crush and shave the ice that dispenses on a refrigerator. This part can be used to repair a refrigerator that is no longer dispensing ice. Sometimes when the ice dispenser malfunctions and makes a loud noise but doesn't dispense cubed or shaved ice, the problem is with the auger and crusher blade. Perform a visual inspection of the auger and crusher blade to ensure no external damage is done to the components.Disconnect the refrigerator from its power source before starting this repair. Open the freezer door to access the ice bucket and dispenser area. The bucket is held in place by fastening clips that can be pushed to remove the bucket. Lay the bucket flat on its back with the auger and blade facing upwards. Remove the old auger and crusher blade by removing the four hex screws. Remove the helix end-cap from the old auger system and replace it with the new one. Repeat these steps in reverse to install the new component.This Whirlpool ice auger and crusher is a genuine OEM product sourced directly from Whirlpool. The part listed is only available individually and is not included with any other parts or original appliances. This part is compatible with Whirlpool, Amana, Kenmore, and Maytag appliances.

This acoustic fiber is the sound-absorbing insulation used in a refrigerator's machine compartment. Replacing a missing or damaged pad reduces operating noise from the compressor area and helps maintain the unit's intended sound levels.

• Absorbs and dampens compressor and condenser fan noise from the rear machine compartment
• Helps reduce vibration resonance transmitted through the cabinet
• Restores sound control when original insulation is torn, saturated, or missing
• Common symptoms: increased humming, buzzing, or rattling from the back or bottom of the refrigerator

• Disconnect power and pull the refrigerator forward for rear access
• Remove the lower rear access panel and note the insulation's placement/orientation
• Position the new pad in the same location; keep clear of coils, wiring, airflow paths, and moving parts
• Reinstall the access panel and restore power; verify no contact or obstruction

This refrigerator defrost timer automatically starts and ends the defrost cycle to melt frost from the evaporator coils. Replacing a failed timer restores consistent cooling performance and helps prevent frost buildup that can restrict airflow.

• Controls the timed switch between cooling and defrost to keep evaporator coils clear of frost
• Common symptoms of failure: heavy frost on the evaporator or back panel, fresh food section too warm, unit runs constantly, or won't resume cooling after defrost
• Restores proper frost removal and airflow for stable temperatures
• Designed to match the original timer's function and wiring connections for applicable models

• Disconnect power before servicing; wear cut-resistant gloves
• Access location varies by model—often in the fresh food control housing or rear machine compartment
• Photograph/label wire positions and transfer them to the matching terminals on the new timer
• Reuse original mounting hardware and install in the same orientation as the original

This factory screw secures appliance components to their mounting points. Replace missing, worn, or stripped hardware to restore a tight fit, proper alignment, and quieter operation across the affected assembly.

• Fastens panels, brackets, covers, or internal parts to the chassis or frame
• Helps maintain alignment and support, reducing rattle, vibration, or looseness
• Replaces missing or damaged screws that have backed out, broken, or stripped
• Restores secure mounting after service when original hardware is lost

• Disconnect power; shut off water or gas supplies before servicing
• Use the correct driver; start threads by hand to avoid cross-threading
• Match length and thread to the original location; do not substitute with longer hardware
• Tighten snugly; do not overtighten into plastic or thin metal

This evaporator defrost heater melts frost from the evaporator coil during the automatic defrost cycle to restore airflow and stable temperatures. Replacing a failed heater helps prevent ice buildup that restricts cooling and leads to warm spots. What it does:

• Heats the evaporator coil to clear frost/ice during defrost
• Helps maintain proper airflow between freezer and fresh food sections
• Typical symptoms: heavy frost on the back panel/evaporator, weak cooling or rising temperatures
• Also cause evaporator fan noise from ice contact and longer run times

• 1 evaporator defrost heater

• Disconnect power before servicing; allow any ice to thaw
• Access the heater behind the freezer's rear panel; avoid damaging fins or refrigerant lines
• Secure the heater and route wires exactly as original, keeping them clear of the fan and sharp edges
• Restore power and verify the defrost cycle per the service procedure

Ice maker water line: 1/4x 8ft.

This black refrigerator toe grille covers the lower front opening, protecting internal components and helping guide airflow through the condenser while giving the appliance a clean, finished look. Replace a cracked or missing grille to restore fit and appearance.

• Helps direct airflow to the condenser area for proper ventilation
• Shields the machine compartment from bumps and debris
• Provides a finished, uniform look along the base
• Replace if cracked, warped, tabs are broken, won't stay attached, or rattles

• Disconnect power before servicing and wear cut-resistant gloves
• Remove the existing grille by releasing clips or removing screws (as designed)
• Align the new grille with mounting points and secure with the original fasteners
• Ensure ventilation slots are clear and unobstructed after installation

This limit switch monitors a set condition and opens or closes its contacts when that limit is reached. Replacing a failed switch restores proper safety cutoff and consistent operation of the appliance's heating or movement system. What it does:

• Senses a limit condition at its mounting point (such as temperature or travel/position, depending on model)
• Changes state at a defined threshold to protect components and wiring
• Interrupts power to heat or motor circuits, or signals a control to respond
• Common failure signs: no heat or shuts down early, runs continuously, won't start, or intermittent operation

• 1 limit switch

• Disconnect power to the appliance before servicing
• Note wire positions; transfer connectors one at a time or take a photo for reference
• Reinstall in the original orientation so the actuator or sensing surface contacts the correct area
• Address root causes (blocked airflow, binding mechanisms, shorted components) to prevent repeat failures

This speed clip is a small retainer that slides over a panel edge to provide a captive thread for a screw. Replacing a worn or missing clip restores a tight, rattle-free hold on the attached component. What it does:

• Slides over a panel or bracket to create a captive thread for a mounting screw
• Maintains tension to resist vibration and loosening
• Helps when a screw spins or won't tighten due to a missing retainer
• Addresses loose, rattling, or misaligned panels or trim

• 1 speed clip

• Disconnect power and, if applicable, shut off water before servicing
• Note the original clip's location and orientation for correct fit
• Fully seat the clip on the edge; start the screw by hand to avoid cross-threading
• Do not overtighten; ensure the component is secure and noise-free