Cae2745fq1 Parts

This lock cam is a small actuator that drives the appliance's door-lock mechanism. It translates the lock actuator's movement into a positive latch, helping the door lock securely when required and release correctly so cycles start and finish properly.

• Interfaces with the lock actuator and latch to engage and release the lock
• Wear, cracking, or rounding can cause the lock not to engage or to stick
• Common symptoms include a door/lid that won't lock or unlock, loose lock lever, clicking without latching, or door/lock-related error messages
• Restores proper linkage travel and switch actuation when the original cam is worn or damaged

• Disconnect power to the appliance before servicing
• Access the lock mechanism per your model; note the cam's orientation and any springs/linkages
• Install the new cam fully seated and ensure it engages the actuator and latch smoothly
• Reassemble, restore power, and test lock operation

This factory screw secures panels, brackets, and other components in your appliance. Replace a missing, stripped, or corroded fastener to restore a tight fit and keep parts properly aligned and rattle-free.

• Secures appliance components and panels in their mounting points
• Replaces damaged, stripped, or missing hardware
• Helps reduce rattling or vibration from loose parts

• Disconnect power; shut off water or gas supplies if applicable
• Match location with the original screw; start threads by hand to avoid cross-threading
• Tighten until snug; do not over-torque, especially into plastic or thin metal
• Reinstall any covers or panels and test for secure fit

This coin chute guides coins from the slide into the coin mechanism so the machine can register payment and begin a cycle. Keeping the chute intact and aligned helps prevent jams and misfeeds in coin-operated laundry equipment.

• Directs coins from the slide to the coin mechanism to register payment
• Helps ensure smooth coin drop, reducing bounce-back and misfeeds
• Common fix when coins jam, fall into the cabinet, or the unit won't start after payment
• Replace if cracked, bent, corroded, or missing

• Disconnect power; shut off gas before service
• Open the coin housing/slide assembly and retain existing hardware
• Install the new chute in the same orientation; align with slide and mechanism, then secure
• Test with sample coins to ensure proper drop and operation before returning to service

This pump drain filter helps protect the appliance's drain pump by screening out debris before it enters the pump. A clean, intact filter supports proper draining and helps prevent clogs and pump damage.

• Screens debris before it reaches the drain pump
• Helps maintain proper draining performance
• May resolve issues like slow or incomplete draining, standing water, or drain-related noises
• Replacing a damaged or missing filter can reduce repeat clogs

• Unplug power and shut off water supply before service
• Access location varies by model; have towels ready for any residual water
• Note orientation of the old filter for correct placement
• After installation, check for leaks and run a brief drain cycle to verify operation

Extends the drain hose approximately 4 feet. You must also order a drain hose connector kit: 285835.

The Drive Motor is an OEM part for Whirlpool washing machines. The drive motor is responsible for powering the agitator or impeller as well as drum rotation during all cycles. It converts electrical energy into mechanical motion needed for washing and spinning laundry.

Causes of a bad drive motor can include failure to start, inconsistent speeds or intermittent operation which are tell-tale signs of normal wear and tear over time.

Symptoms of a failed drive motor include:

• The washer not starting or completing cycles
• Abnormal sounds such as grinding or clicking during operation
• Noticeable vibrations compared to typical wash cycles
• Inability to spin or properly agitate clothing

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This lower console harness routes power and signals between the console control area and the appliance's lower components, restoring reliable electrical connections for controls and indicators. Use this harness to replace damaged or worn wiring in the lower console. What it does:

• Carries control and power circuits between the lower console and internal components
• Replaces frayed, pinched or broken wiring that can cause intermittent or failed console functions
• Helps resolve symptoms such as unresponsive console buttons, missing indicator lights, or intermittent operation related to lower-console wiring
• Maintains correct connector routing and secure plug connections for consistent performance

• Disconnect power to the appliance before starting any repair to avoid shock hazard
• Access the lower console per the service guide; remove panels and fasteners as needed to reach the harness routing
• Match connector shapes and colors; fully seat each plug and secure any routing clips or ties
• Inspect surrounding wiring and components for damage while replacing the harness

This pushbutton installs in the control console and actuates the underlying switch, restoring positive, reliable selection of a cycle or feature and a clean, finished appearance when the original button is worn, sticky, or broken. What it does

• Provides the user-facing cap that presses the internal control switch
• Restores smooth button travel and positive engagement
• Helps ensure selections register consistently
• Common symptoms: button cap cracked/missing, sticks or won't spring back, selection only registers when pressed hard, loose or wobbly button

• 1 pushbutton

• Disconnect power before servicing to avoid electrical shock
• Access the control/console per your service manual
• Note orientation; release retaining tabs and remove old button
• Seat the new button fully; test travel and function before reassembly

The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear bulkhead to the tub, ensuring vibrations are reduced through solid mounting points. Properly installed screws dampen oscillating movement.

Causes of a bad screw include damage from water exposure like corrosion or breakage from stress concentrations if the tub bangs around during imbalanced loads. 

Symptoms of a bad screw include:

• Loose or detached rear bulkhead allowing side-to-side play
• Excessive noise and shaking felt through the surrounding walls   
• Development of micro-cracks around screw holes over time
• Potential leak paths if holes are no longer sealed 

This Whirlpool replacement screw restores a stable suspension system. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This is the factory replacement microwave door assembly. It restores a smooth, secure door closure and proper operation so the unit can open and close reliably and look like new. What it does:

• Provides a complete, aligned door to open/close the cavity smoothly
• Ensures latch hooks engage properly so the appliance can operate
• Replaces doors that are cracked, warped, or have broken handle mounts
• Addresses issues like the unit not starting unless the door is pressed, or stopping when the door is moved
• Helps resolve sparking/arcing around the door opening caused by a damaged door choke or screen

• One door assembly

• Disconnect power at the breaker before servicing; microwaves contain high-voltage components
• For over-the-range units, support or remove the microwave from the wall to safely access and handle the door
• Transfer any reusable hardware/hinge pins/trim from the original door as needed
• Align the hinges and verify the door closes, latches, and opens smoothly before remounting

Size: 1-1/16 x 5/8 inch. Used for fill hose. For a 4 pack order 285448A

Includes connector and both clamps.

The Capacitor is an OEM part for Whirlpool washers. It is responsible for starting the motor and keeping it running smoothly during the washing cycle. It stores electrical energy and delivers it to the motor when needed, providing the necessary power for the washer to function properly.

A bad washer capacitor can occur due to electrical malfunctions, wear and tear, or damage to the capacitor itself. If you notice symptoms such as the washer not starting or spinning, the motor making unusual noises, or the washer not completing cycles, it may be time to replace the washer capacitor.

Symptoms of a bad washer capacitor include:

• Washer not starting or spinning
• Unusual noises coming from the motor
• Incomplete cycles or erratic behavior

Repair your washer by replacing the faulty or worn-out washer capacitor with this genuine OEM part.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

Size: 29 1/4 inches x 31 1/4 inches. This universal washer drip tray is large enough for duet washers and sits under the washer to protect your floors from scuffs, spill, etc. Includes a PVC drain fitting.

Size: 8-18 x 1/2 inch.

Right hand side. For screws use WPW10119828.