Ced4205ayj Parts

This bearing ring is a small, low-friction spacer used in the dryer's drive system to let rotating components spin smoothly and quietly. Replacing a worn ring helps reduce drag, eliminate squeal, and protect related parts. What it does:

• Provides a bearing surface between a rotating wheel/pulley and its bracket
• Helps maintain smooth belt tracking and consistent tumble
• Reduces friction and wear on the belt and pulley/roller
• Common symptoms of wear: squealing/chirping while running, intermittent drum start, drag or burning-rubber smell

• 1 bearing ring

• Disconnect power; for gas dryers, also shut off gas supply
• Access the drive system; release belt tension and remove the affected pulley/roller as required
• Note the order/orientation of spacers, washers, and clips; install the new ring in the same position
• Hand-rotate the assembly to ensure free movement before reassembly and testing

This factory sensor provides critical feedback to the control so your appliance can adjust operation and protect components. Replacing a failed sensor restores accurate readings and helps eliminate erratic cycles and nuisance error messages. What it does:

• Monitors operating conditions and sends a signal to the main control
• Helps regulate timing, heating, and other functions based on real-time data
• A failing sensor can trigger error codes or stop a cycle prematurely
• Intermittent faults may cause unusually long/short cycles or inconsistent results

• 1 sensor

• Disconnect power before servicing to avoid electrical shock
• Access and mounting vary by model; refer to your unit's service information
• Transfer any brackets, seals, or screws from the original part if required
• Handle wiring connectors carefully; avoid pulling on the wires

This lint screen grille covers the lint filter opening inside the dryer drum. It supports the lint screen and provides a smooth surface at the opening to prevent snags, restoring proper fit and safe airflow. What it does:

• Supports and aligns the lint screen so it sits flush in the opening
• Shields the blower intake and keeps fabrics from contacting internal parts
• Provides a smooth edge to help prevent clothes from snagging or fraying
• Typical failure signs: cracked or missing grille, broken tabs, lint screen not seating properly, clothes catching near the lint opening

• 1 lint screen grille

• Disconnect power before servicing
• Open the dryer door and remove the screws securing the existing grille
• Lift out the old grille, position the new grille, and secure it with the existing screws
• Reinstall the lint screen and verify it slides smoothly and sits flush

This heater box is the protective housing that encloses and supports the heating element in your appliance. Replacing a warped or damaged housing helps restore safe, efficient heating and protects nearby components from excessive heat.

• Holds the heater element securely and maintains proper spacing from surrounding parts
• Shields adjacent wiring and components from direct heat
• Helps maintain consistent heating performance when the original housing is heat-damaged or cracked
• Common symptoms include visible melting/warping, loose element fitment, burning odors, or repeated safety shutoffs

• Disconnect power (and gas supply, if applicable) and allow the unit to cool completely before service
• Take photos of the existing layout to aid reassembly and wire routing
• Transfer the heater element and any model-specific hardware to the new housing in the same orientation
• Ensure wiring is clear of sharp edges and heat sources; reassemble and test for proper operation

The Coin Box is an OEM replacement part for Whirlpool combo washer/dryers. It provides a storage space for coins used to operate the unit. The coin box slots ensure collected change remains safe and secures payments for laundry cycles.

Causes of a bad coin box can be normal wear from hundreds of deposits, minerals clogging slots, or physical damage compromising security.

Symptoms of a bad coin box include:

• Coins not being accepted or properly collected
• Box distorting shape or developing cracks over time
• Change falling out or going missing

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air and some Kenmore models.

This locking nut is used for many purposes on a range of machines including household appliances. This nut is often used for leg leveling for machines. It will help with vibrations from washers and dryers. If the nut is used for this purpose and goes missing or becomes damaged, it could cause the machine to vibrate more and seem louder.Nuts are made from metal and are built to last a long time. However, there can still be issues that arise. In some cases, the nuts might go missing if they become loose and the machine is moved. They could also corrode over time and need to be replaced. The replacement of the nut is typically a fast and simple repair.The nut is a genuine OEM replacement part sourced from the manufacturer. It can work with washers, dryers, and combo machines, and is compatible with models from Whirlpool, Kenmore, Maytag, and Roper. The part is sold individually. Owners may want to have several on hand.

10 - 16 x 1/2

Left hand hinge. For right hinge use WP8066056

This replacement timer restores accurate, dependable timing for your appliance's functions. If the original timer sticks, fails to advance, or delivers inconsistent results, installing this part brings back proper countdown and time-based control.

• Regulates time-based operations or countdown features depending on the model
• Switches circuits on/off based on elapsed time to keep functions on schedule
• Accepts a user-set duration via dial/knob or panel input
• Typical failure symptoms: time does not advance, dial won't turn or sticks, erratic timing, clicking/buzzing, or no response when set

• Disconnect power to the appliance before servicing; shut off gas supply if applicable
• Access the control area, note or photograph wire positions, and transfer wires to the new timer one at a time
• Reuse the existing knob, bracket, and mounting screws from your unit as needed
• After installation, verify the timer starts, advances, and signals completion before reassembling fully

This replacement screw secures panels, brackets, and other components in your appliance to keep them aligned and rattle-free. Replacing worn, stripped, or missing hardware restores a tight fit and helps maintain safe, quiet operation.

• Fastens panels, brackets, or internal parts to the cabinet/frame
• Helps maintain alignment to reduce vibration and rattling
• Replaces lost, stripped, or corroded screws
• Common symptoms: loose panels/trim, rattles, or a screw that won't tighten

• Disconnect power; shut off water or gas if applicable
• Match thread and length to the original; replace one at a time to keep alignment
• Start threads by hand to avoid cross-threading; use the correct driver
• Tighten snugly—do not overtighten, especially into plastic or thin sheet metal

This sensor monitors humidity inside the microwave cavity so sensor-cook and reheat features can automatically adjust time and power. Replacing a failing sensor restores accurate automatic cooking and helps prevent premature shutdowns or "Sensor" error messages.

• Detects steam/humidity in the cavity during sensor-based cooking cycles
• Sends feedback to the control to optimize cook time and power levels
• Failure can cause "Sensor" errors, sensor-cook cycles that won't start or end early
• Manual timed cooking may still work while sensor-cook modes misbehave

• Disconnect power before servicing; microwaves contain a high-voltage capacitor that can retain a dangerous charge
• Access is typically behind the top grille/control area; note sensor orientation before removal
• Handle the sensor by its body; avoid contaminating the sensing face
• Route wiring as original and ensure the connector is fully seated before reassembly

Specs: 10-16 x 1/2 inch.

The Whirlpool Dryer Door Catch is an OEM part for Whirlpool dryers. It secures the dryer door closed during operation, ensuring the safety and proper functioning of the appliance. This component engages with the door latch to hold the door shut, allowing the dryer to operate without interruption.

Causes of a bad dryer door catch can include normal wear and tear from frequent use, accidental damage, or deformation of the catch or latch that prevents proper engagement. Over time, the door catch can become loose or break, necessitating replacement to maintain the dryer's performance and safety.

Symptoms of a bad dryer door catch include:

• The dryer door not staying closed during cycles
• Difficulty closing the door securely
• The dryer stopping mid-cycle due to the door opening

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This belt restrainer is the small guide that keeps the dryer's drive belt on the motor pulley. It prevents the belt from walking off during operation, supporting consistent drum rotation and reducing premature belt wear. What it does:

• Guides and retains the drive belt on the motor pulley
• Helps maintain proper belt tracking with the idler assembly
• Can help with symptoms like drum not turning, belt repeatedly slipping off, burning rubber smell, or frayed belt edges

• 1 belt restrainer

• Disconnect power; for gas dryers, also shut off the gas supply
• Access the motor area per your model (remove front or lower access panel)
• Position the restrainer adjacent to the motor pulley with slight clearance to the belt; route the belt correctly around drum, idler, and motor
• Hand-rotate the drum to confirm alignment before reassembly and testing

This Dryer Drying Rack creates a stationary shelf inside the drum so items that shouldn't tumble—like shoes, sweaters, and hats—can dry gently. Replace a missing or damaged rack to restore safe, non-tumble drying capability.

• Provides a stable platform inside the dryer for items that need to stay still while drying
• Helps reduce wear, scuffing, and noise from tumbling delicate or bulky items
• Restores function when the original rack is cracked, warped, or missing
• Common symptoms: rack won't seat/lock, sits unevenly, or items won't stay on the rack

• Disconnect power before installing
• Open the door and seat the rack so the rear support engages the back ledge/slots and the front rests on the door opening
• Ensure the rack is secure and clear of the rotating drum; load items evenly
• Remove the rack before returning to normal tumble cycles

Color: Chrome