Csp1802465 Parts

• Will not tumble

I did a little research and found out that the dryer drum rollers needed to be replaced. I decided that since I would be replacing the 4 drum rollers that I should replace the belt and the belt drive pulley. This was a simple project thanks to YouTube. I used one of appliancepartspor videos to st me through the repair. Now I have a dryer that does not squeal like a pig! Read more

• Takes too long to dry

My fiance was involved in a very nasty divorce where a very biased female judge forced him from his home for 14 months before he could take up residency again. He brought me back with him and I witnessed the grotesque damages she intentionally inflicted on his property. His washer and dryer are very expensive and high-end, as is the home and all his contents. One of the many damages she caused was that she had not cleaned the dryer lint filter in 14 months and the lint was a thick carpet which... Read more

• No heat or not enough heat

I replaced the "heating element" which was bad.........as well as the "Thermst-fix" and "Thermal Cutoff" which are located on the side of the element mounting location while I had the dyer all opened up and the element mounting tube removed.......I also replaced the Dryer Thermister which is located on the top of the blower fan.....To get to these parts, you must open the top of the dryer which has spring latches on both sides of the front corners... they need to be pressed in (use a putty... Read more

I wanted to avoid pulling the drum. Luckily, my blower was easily accessed by pulling the front bottom panel. A couple of sheet metal screws were all I needed to remove the fan housing cover. I knew the fan was on reverse threads, i.e. righty-untighty. As it spins it tightens so no need for a retaining nut. I took off a screw holding on the exhaust tube and wiggled it out. I found the broken teeth inside. With the tube out of the way I was able to slide a crescent wrench in back and place... Read more

This was actually one of the easiest fixes I’ve done. All that was required was to remove 3 screws to remove the broken part. I used a pair of pliers to remove the moisture sensors from the broken part to the new one. Read more

I WENT ON-LINE & FOUND APPLIANCE STORE,THEY HAD MY PARTS, I ORDERED, THEY WERE SHIPPED IMMEDIATELY,WITHIN UNDER TWO DAYS.THIS WAS EXACTLY WHAT THEY SAID THEY WOULD DO.ALSO THE REPAIR VIDEO SHOWED ME HOW TO RUN THE BELT ON THE TENSIONER,I WAS AMAZED AT HOW SIMPLE & QUICK EVERYTHING WENT BACK TOGETHER.THANKS APPLIANCE STORE FOR BEING THEIR TO HELP ME GET MY GRANDSON"S DRYER BACK WORKING,I GIVE YOUR SITE A < A+ >. Read more

• No heat or not enough heat
• Takes too long to dry

Since the dryer was 24 years old I opted to replace all the possible problem components, instead of just the bad one. The parts aren't that expensive and do to their age I figured it was worth it to avoid having to go back into the dryer in a few months. The repair was surprisingly easy and went pretty much as the video instruction AppliancePartPros provided with one exception. Because, my model was much older than that used in the video, I had a more difficult time replacing the Heating... Read more

Watched You tube videos to narrow the problem down to old deteriorated gaskets. Read more

• Will not drain
• Pumps but will not spin
• Timer will not advance
• Doesn't shut off

The lid shut-off switch is located behind the lid How About That. I order the plastic ball the hold the lid in place plus the lid shut off switch. I watched the video that AppliancePartsPros.com has on how to replace the lid and the plastic balls. I removed the lid to get to the two philips head screws to remove that part of the shut-off switch. I took the new switch out of the package and compared it to the old switch. I assembled the switch just like the old switch look using the new... Read more

Checked thermal fuse, belt pulley switch, door switch, and motor windings (primary 2.3 ohms start 2,2 ohms). Called Appliance Pros, told them my problem. They said that it appears to be the motor even though the ohm readings seam Ok and that I could return the motor if it was not the problem. I ordred the motor and blower wheel. Installed the new motor and everything worked! The only difficult part was that the motor blower had to be chiseled out. Their motor repair video was a great help. Read more

Replaced the Rollers, Pins, belt and belt tensioner. One thing to keep in mind. In the video it was said that the back and front roller pins were different by lengths. They were the same length for my model. The differences were found to be the rear pins have left handed threads and the front ones were standard right hand threads. Keep that in-mind when you are trying to remove them. Read more

Replace the drum drive belt and tension pulley assy. Read more

• Too hot
• No heat or not enough heat
• Shuts off too soon
• Takes too long to dry

This Maytag dryer was bought in 1985 if memory serves. It has worked hard with few repairs done by yours truly over the years. Thanks to the engineering and excellent design by Maytag staff, removing parts are relatively easy. Once I opened the unit, I found it to be full of lint. I cleaned the entire inside and the vent pipe duct work. I found the blower wheel assembly worn. Though it was not cause of my problem, I decided to change it along with the igniter, heater relay and the fan belt. I... Read more

Replaced the Rollers, Pins, belt and belt tensioner. One thing to keep in mind. In the video it was said that the back and front roller pins were different by lengths. They were the same length for my model. The differences were found to be the rear pins have left handed threads and the front ones were standard right hand threads. Keep that in-mind when you are trying to remove them. Read more

Bought the leveling feet and screwed them in the bottom and they work great. Read more

This was actually one of the easiest fixes I’ve done. All that was required was to remove 3 screws to remove the broken part. I used a pair of pliers to remove the moisture sensors from the broken part to the new one. Read more