Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Fix a dryer that won't heat or takes forever to dry clothes. This heating element assembly restores proper drying. Video guide included.
Found a video on UTube on how to dissamble the dryer. It was striaght forward and helpful. In the process I found an unusal amount of lint in the pipe from the dryer to the vent pipe to the outside It was nearly blocked about 10" up the pipe.. Read more
The Heating Element Assembly is an OEM part for GE dryers. It is responsible for generating the heat necessary to dry clothes during the drying cycle. This assembly includes the heating element itself, which heats up when electricity passes through it,
I replaced the heating element supplied by AppliancePartsPros.com. It took me longer than the estimated 30 minutes to an hour cited in the good instructional video. A few things took more time than I had expected: 1. Removing the top of the dryer unit resulted in my breaking off the three plastic tabs that is used to anchor the top to the structure below. In putting it back together, I didn't need those three tabs as the side plastic structure on each side will secure the top to the... Read more
The Door Latch is an OEM part for GE dryers. This part ensures the dryer door stays securely closed during operation, activating the safety switch to allow the dryer to operate. The latch mechanism engages with the door strike to lock the door, prevent
My GE dryer from the late 80's/early 90's was squealing when it would start up, belt or bearing I was thinking. I found a manual online that covered my model and I watched a video on this site that showed me how to take it all apart, mine was a bit different but the principles were the same. I took it apart and added some quick-disconnects to 2 wires so next time I can take the front panel off easily. When I got to the bearing it looked worn but not bad so I cleaned it and put it back. ... Read more
The bearing retainer secures the drum bearing assembly in your dryer. Replace if cracked, broken, or worn to restore proper structural support.
A few months back I changed out the "Bearing Slides" on the front side of the drum thinking that would stop the annoying squeaking every time we use the dryer. They were very worn and one was missing. But to my dismay it only lessened it by about 10%. After doing a bit more research I discovered the "Rear Shaft Bracket Assembly" also needed replacement. The tip was worn way down and clearly the source of the noise. It was actually a very simple repair except for the fact that the key to the... Read more
The Blower Wheel is an OEM replacement part for GE dryers. It has a role in the air circulation within the dryer, aiding in the even and efficient drying of clothes. The blower wheel, connected to the motor, helps in expelling the moist air out of the
New wheel didn't look different than the other wheel, but we put it on, it works and we're very happy. Read more
Secures the blower wheel to the motor shaft. Replace when the wheel loosens or moves, causing rattling or rubbing noise. Includes clamps and screw.
Had to remove the front and top panel on the dryer, disconnect the belt and remove the drum. From there it was two screws to slide out the motor assembly with the fan attached and one bolt to remove the clamp and screw kit holding the fan in place. They kit was worn and was allowing the fan to move forward and back on the motor shaft. Once replaced it took about 5 minutes to reassemble and my dryer now purs like a kitten. Read more
This dryer motor kit powers the drum and blower. Replacing a weak or failed motor restores proper tumbling and airflow so the dryer starts reliably and dries loads more evenly.
Replaced the motor with a new one, if I can offer any advice about doing this job, make sure to keep track of where each wire goes on the motor and whatever wires need to be disconnected. There are a few good video's online showing how to do this job and can save you a lot of time and frustration. Read more
Dryer won't start or keeps tripping the breaker? A damaged terminal block disrupts power distribution. DIY repair typically takes 30-45 minutes.
Had to replace power cord and entire terminal assy. Read more
Fix melted plastic or goop marks on clothes with a new dryer heat diffuser. Replaces damaged diffuser that causes staining. DIY repair with 3 screws.
Removed 3 screws which required a torx bit. Used small headless nails to line up the holes and use as a guide for sliding on new diffuser. Put screws in one at a time and tightened down. rotating the drum helped with slight mis-alignement with the screw holes. Read more
Dryer door won't stay closed or pops open during cycle? This mounting plate anchors the door strike for secure latching. Quick DIY fix with video guide.
We ordered a door switch, dryer latch and strike plate. We realized that we only needed to replace the door switch. We watched a few videos and then replaced the switch. We couldn’t find a video for our model but they did give us a pretty good idea about what we needed to do. The hardest part was getting the original door switch out, all of the videos we watched showed us that it would pop out with a little pressure from a flat head screw driver, from the front of the switch. We could not get... Read more
The Thermistor is an OEM replacement part for GE dryers. This temperature-sensing device monitors air exhaust temperatures and communicates real-time readings to the control board. Precise thermistor functioning ensures the heating elements and drum en
Checked vent first to see if there was a blockage. Removed top, front and drum of dryer. Replaced all sensors including flame detection and gas valve coils. Re-assembled and tested. Dryer was now heating Read more
Replaces a broken, cracked, or damaged lint trap duct assembly in your dryer. Directs airflow from the drum to the exhaust vent and houses the lint trap.
Our GE front loader dryer is approximately 10 years old. It started making a loud noise. Before we sank another $600 for a new dryer, I decided to go online to search Youtube videos to try to find out if anyone else had the same problem. I found that a lot of dryers had drum support bearings that wore out and needed to be replaced and a lot of dryers were also having clothes caught up in them. I then found an Appliance Parts Pro video on how to fix this problem and found out what parts... Read more
Captures lint and debris from dryer airflow to prevent vent clogs and maintain efficiency. Replace if torn, damaged, or no longer sealing properly.
I ordered a new filter and replaced the torn one. Read more
This cleaning felt mounts on the dryer's front shroud. It lightly contacts the rotating drum to wipe away lint and residue, helping keep the drum edge clean and supporting consistent airflow to the lint filter.
Selected and ordered parts from online drawings. Watched videos showing how to make repair. Replaced worn parts with new ones. Suggested improvement: Videos didn't show my model (I know there are many models, showing all is probably not possible). In case of Felt the video showed a Maytag dryer when my model was GE. In my case Felt had torn and dislodge from slot so I didn't know exactly how it should be installed. A simple picture of the installed Item would help. Also the parts list should... Read more
Hi-limit thermostat. L210.
Replaced the high limit safety thermostat. Ordering was easy, and the part came quickly. The video on the web site was helpful, although I was not able to follow the instructions fully. Unless you have super skinny, long arms, you cannot reach under and around the dryer tub to reach the belt tension arm. I ended up having to remove the side panel of the dryer to remove the belt from the motor. Replacing the thermostat was simple enough. At this point, it seems to have corrected the... Read more
Fix a dryer that won't heat with this outlet backup thermostat. Mounts on exhaust duct for over-temperature protection. DIY repair in under 1 hour.