Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Drum support roller assembly for dryers. Installs inside the cabinet to support the drum during rotation. Replace when worn, flat-spotted, or broken.
I consulted with the internet and your website and determined I had a bad roller wheel. I was going to buy just one but determined if you have to take the thing apart, just replace all of them. These lasted 10 years after all. Opened up You Tube for the method to take the dryer apart. After doing the washer last year, I felt pretty bold and just ripped into the project. Within 30 minutes I had the drum out and located the problem wheel ( rear right side). It was locked up due to hair build up... Read more
Connects the motor to the drum so it can tumble. Replace if the drum won't spin, makes squealing noises, or clothes aren't drying. Confirm fit by model number.
I disassembled/reassembled the dryer according to the ApplianceParts Youtube video. With my limited electrical knowledge (just enough to be dangerous) I initially figured it was a problem with the heating unit, sensor(s), or the control board. After diagnosing the problem (bad thermistor), I had to order the parts and was able to repair and reassemble the dryer several days later. After removing the drum, I cleaned all the dust etc. out of the inside (it gets dirty in there!) and inspected,... Read more
Dryer not heating or shutting off mid-cycle? A faulty blower thermostat disrupts airflow regulation. Front-access repair with basic tools in 30-60 minutes.
Checked and cleaned vent which was in need of cleaning, but not too bad (I do not consider this a primary causal detail, but can be a problem, so clean yours). Replaced Hi-Limit Thermostat (safety thermostat) after confirming the circuit was open with ohm meter. While I was in there, I completely cleaned the heater and ducting and internal workings of the dryer. Confirmed the heater coils were good via 20ohm, 20ohm, 40ohm readings (LG service manual has wrong readings). Two weeks later, same... Read more
Dryer not sensing when clothes are dry? Replace the moisture sensor bar to restore auto-dry cycles. Moderate DIY repair with video guide available.
After I cleaned out the typical 1.5 pounds of lint from the vent, ( I do it every 2 months), I went searching for a solution. I found 6 possible causes on this site and purchased everything except a new burner; I wasn't going to go that far. Let the fun begin. Since my vacuum was still nearby, I thought I was ready for anything. Wrong. After I watched all the videos again for reassurance, I went in with screwdriver in hand and laptop nearby. I removed the top and looked inside. Don't be fooled,... Read more
Replacement dryer lint filter guide cover. Installs over the lint screen housing to prevent small items from entering the duct. Replaces cracked covers.
I have order three parts, guide filter, cover guide, and sensor assembly. My previous cover guide was from two parts, when sensor assembly was one of them. New part ( guide cover ) was all in one piece so I just transfer old metal part of sensor to new cover guide and I don't need that sensor assembly anymore. I have ordered all three parts overnight by Fedex, ordered 15 min before 5pm, so next day it was here. Dryer is fixed, I'm happy. Read more
Dryer lint filter screen traps lint and debris during drying cycles. Replace if cracked, damaged, or lost to maintain airflow and efficiency.
I purchased a new replacement. Read more
Maintains tension on your dryer's drum belt for smooth rotation. Replace if pulley wheel is cracked, shaft worn, or assembly moves excessively during operation.
Was going to order 4 new wheel & spindle sets, then saw you could get just the wheel for 1/3 the cost, so I ordered those. Then in the frequently ordered other items I saw the idler wheel assy. So I ordered one of those also. Glad I did, it was in worse shape than any of the wheels which still seemed to spin freely after I got all the hairs and crap off them. Anyways, went by the video step by step. Pretty straightforward. Have a good vacuum handy, I’m surprised that it used to dry at all... Read more
Dryer not heating or overheating? The high limit thermostat shuts off heat at unsafe temperatures. Moderate difficulty repair requiring partial disassembly.
Replace your dryer drum seal when clothes take longer to dry or you notice lint buildup. Maintains heat efficiency and prevents air leaks. Confirm fit with your model number.
From reading "troubleshooting" sites on the internet, originally thought I'd be replacing the front & rear drum rollers, so I ordered the rollers, and a new belt before I opened up the dryer, taking it out of use. When I opened it up the front rollers were "shot", and the front bulkhead was "totaled". Waited for parts to arrive (within 2 days), and successfully replaced front & rear rollers, bulkhead, drum seal. The on-line videos really helped me ensure I was keeping in the right order. My... Read more
Dryer won't heat or takes too long to dry? A faulty igniter often causes no heat in gas dryers. Moderate DIY repair with front panel removal required.
I first ordered a thermostat and ignitor and replaced and that did not work. I asked Appliance Parts Pros their opinion in the chat and they said it was the coils in the gas valve but you had to replace the entire valve as the coils are not sold individually. So i ordered the part and also replaced the thermistor and drum belt while i had the dryer apart anyway! And this fixed the problem! These guys are the absolute best and most helpful i have ever dealt with. This is the second time i... Read more
Guides and secures the lint filter in place within your dryer. Replace if cracked, broken, or missing to properly hold the lint screen assembly.
Idler pulley maintains tension on the dryer belt. Replace if worn, cracked, or causing belt slippage. Installs between motor and drum support system.
I have an LG dryer purchased in 2007. Model: DLE9577SM. It was squeaking at start-up and rumbling a little. Not knowing what parts I would actually need, I ordered rollers with/without assemblies, tensioner pulley-only, new belt. After viewing this video a couple of times, I attacked my machine which is located in the comfort of my garage. Lots of room to spread out. Nice. This disassembly went OK however because, I suspect, my machine is 13 years old, the removal of the control panel was... Read more
Converting your dryer from natural gas to propane? This LP conversion kit includes the orifice and components needed. Moderate difficulty repair.
Ordered conversion kit from Appliance Parts Pros.com and installed it myself. Most difficult part of the repair, was the removal of the front casing of the dryer to access the location of venturi tube to be changed out. The instructions were helpful, but not specific enough for my dryer. Once the casing was off, the job was not too difficult - you will need a set of short screwdrivers to remove the burner flange and close the pressure adjustment screw, normal length screw drivers will come into... Read more
Dryer won't start or stops mid-cycle? A faulty door switch assembly prevents operation. This straightforward repair restores normal function in 30 minutes.
Bought a new switch assembly, watched the video, and replaced the switch. Thr dryer now runs fine. Replacement part matched esxactly. Read more
Side venting kit for dryers. Redirects exhaust from rear to side of cabinet. Perfect when space is limited or side venting is preferred over rear.
This was a pretty simple install if you know how to take apart your dryer. I have a kenmore dryer which is identical to an LG dryer. My kenmore dryer was actually made by LG at that time. You can find the specific model on youtube and see how your dryer comes apart. While doing this i cleaned all the inner parts of my dryer. The parts that come in the kit can be bought at home depot for much less but you don't know what length you need. I ordered the kit so I could have the back plate and... Read more
Illuminates your dryer drum for easy loading and unloading. Replace when burned out or flickering. Verify fit with your model number before ordering.
After unplugging the dryer from the wall socket, I used a screwdriver ( Phillips ) to remove the light cover fixture. This gave me access to the bulb which had burned out. I first use my fingers to remove the bulb but the base came lose from the glass bulb. I then used a needle nose pliers to remove the metal base of the bulb from the light fixture. Once the metal base was removed I used my fingers to replace the old bulb with a new one. It screws in easily. Now I replaced the light fixture... Read more