Du912pfggo Parts

Size: 8-32 x 1/4 inch.

Fix a dishwasher timer that won't shut off or gets stuck in a cycle. Common repair when the dial is hard to turn or cycles run too long.

The Thermostat Clip is an OEM part for Whirlpool dishwashers. It plays an important supporting role by securely fastening the thermostat sensor inside the wash chamber. 

Symptoms of a faulty Thermostat Clip can include:

• Fluctuating or inconsistent water temperatures between cycles 
• Inability to properly detect temperature for desired heat levels
• Longer cycle times needed for reaching required temperatures
• Strange sounds or condensation around thermostat connection

Causes could arise from typical wear and tear stresses weakening plastic retaining clips. Exposure to harsh detergents may also erode clip material integrity over time.

This OEM replacement part is compatible with KitchenAid, Jenn-Air, Kenmore, and select Hotpoint and Roper dishwasher models as well. 

Wire harness elbow connector for dishwashers. Replaces damaged, cracked, or broken electrical connectors that route power between components.

Standing water in dishwasher bottom or leaking onto floor? This impeller and seal kit repairs worn bushings and seals. 15-minute DIY fix.

The Dishrack is an OEM replacement part for Whirlpool dishwashers. It measures 21" wide x 21" deep. It provides a stable framework for organizing and holding dishes, glasses, utensils, and other items during the washing cycle. Designed to fit securely in the dishwasher, it ensures proper water flow and cleaning efficiency for all loaded items.

Causes of a bad Dishrack can include prolonged exposure to high temperatures and moisture, leading to rust or corrosion, damage to the coating from sharp utensils, or bending or breaking due to heavy or improperly loaded items. Over time, these issues can compromise its functionality.

Symptoms of a bad Dishrack include:

• Rust or peeling coating on the rack
• Broken or bent tines that can’t hold dishes properly
• Difficulty sliding the rack in and out of the dishwasher

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Seals the pump housing to prevent water leaking from the tub onto the motor. Replace if you see leaks around the circulation pump area. Confirm fit by model.

Seal gasket for dishwasher inlet base assembly. Replace if you notice leaks, moisture buildup, or debris entering internal components. Confirm fit.

This is the electric heating element located at the bottom of the dishwasher tub that heats water during wash cycles and provides heat for the drying cycle. It is a looped metal element that generates heat when electrical current passes through it. Replace this part if your dishwasher is not heating water properly, dishes come out wet or cold after the drying cycle, or if the element is visibly damaged or burned through.

Dishwasher won't drain or overflows? A missing or worn check ball can cause backflow issues. This small part maintains one-way water flow in the valve.

This vent screen covers the dishwasher door vent, allowing steam to escape while blocking food particles and debris. Replacing a damaged or missing screen helps maintain proper airflow and can reduce moisture and odors around the vent area.

• Screens the door vent to keep debris out of the vent duct and fan path
• Maintains airflow for venting steam during the dry cycle
• A clogged, cracked, or missing screen may lead to moisture at the vent, odors, or reduced drying performance
• Replace if warped, broken, or lost during service

• Disconnect power to the dishwasher at the breaker before servicing
• Open the door and remove inner-door screws to access the vent assembly
• Remove the old screen, seat the new screen fully and evenly, then reassemble without overtightening
• Run a short cycle and check the vent area for proper airflow and moisture

Secures knobs, trim, or linkages to shafts inside your dishwasher. Replace if broken, cracked, or missing to prevent components from loosening.

This drain impeller spins inside the drain pump to move wastewater out of the appliance, restoring normal draining and reducing standing water. It's a direct-replacement pump impeller designed to fit the original pump housing. What it does:

• Drives water through the drain pump so the washer can empty properly
• Worn or broken impellers can cause slow or no draining and standing water
• May produce unusual pump noise or vibration when damaged
• Helps prevent motor overload by maintaining proper water flow

• One drain impeller

• Disconnect power before accessing the pump assembly to avoid electric shock
• Inspect the pump housing and fasteners; replace any damaged clips or seals as needed
• Reassemble pump and test a short drain cycle before completing the repair

Screw for wash impeller.

Replacement mounting screw for securing panels, brackets, and components to your appliance chassis. Needed when original screws are stripped or missing.

This is a small rolling caster wheel designed to support and allow easy movement of the appliance during installation or repositioning. It mounts to the underside of the unit to enable smooth transport across floors. Replace this wheel if it is broken, seized, or missing, which can make the appliance difficult to move and may cause floor damage.