Eifls6olsso Parts

The Vane is an OEM part for Frigidaire washing machines. This part is responsible for the movement and circulation of clothes inside the washer drum during the washing cycle. 

Causes of a bad vane can include wear and tear from regular use, physical damage from foreign objects in the drum, or degradation of the material over time.

Symptoms of a bad vane include:

• Clothes tangling or not moving properly during the wash cycle
• Increased noise during operation
• Visible damage or wear on the vane
• Poor cleaning results

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This motor control board regulates the washer's drive motor, managing speed and direction for tumble and spin cycles. Replacing a failed board helps restore drum movement and consistent cycle performance when the motor no longer responds. What it does:

• Controls drive motor speed and direction during wash and spin cycles
• Executes motor start/stop commands from the main control
• Failure can cause no spin, no tumble, or intermittent drum movement
• Trigger motor-related fault codes on some models

• Includes: 1 motor control board

• Disconnect power before servicing; observe ESD precautions when handling the board
• Access the control board per your model's service manual (typically in the base or rear cabinet area)
• Transfer wire connectors one at a time to the new board; ensure each is fully seated and latched
• Mount securely, reassemble, and run a diagnostic or spin test to verify motor operation

This is a dispenser inlet gasket intended for use on washing machines. This part ensures that the hot and cold water lines do not leak at the point where they are connected to the appliance. If the washing machine is leaking, the gasket may need to be replaced.Replacing a dispenser inlet gasket in a washing machine can be done easily. Screwdrivers and pliers are required. Disconnect the appliance before starting the repair. Wear work gloves for safety. The hot and cold water lines should both be turned off and removed to prevent flooding.This dispenser inlet gasket is an authentic OEM replacement part. It is sourced from the manufacturer. The replacement component is made of high-quality materials. It can be installed in several different models of washing machines. The dispenser inlet gasket is compatible with appliances produced by Frigidaire, Gibson, Electrolux, Westinghouse, and Kelvinator brands.

This drain pump assembly actively removes water from the washer tub during drain and spin cycles, helping prevent standing water and cycle interruptions. Replacing a worn pump restores proper draining and reliable cycle completion.

• Pumps water from the tub through the drain hose to the household drain
• Common symptoms: no drain or slow draining, water left in tub, cycle stops due to drainage issues
• May present with unusual pump noises (buzzing/grinding) or leaks at the pump housing
• Restores proper water evacuation to allow cycles to finish

• Unplug the appliance and turn off water supply before servicing
• Expect residual water—use towels or a shallow pan when removing hoses
• Access the pump (front lower or rear panel varies by model); disconnect wiring and hoses, and transfer any brackets/grommets from the old pump if needed
• Clear the drain filter, sump, and hose of debris; then test for leaks after installation

This metric machine screw features an M5 x 0.8 thread used to secure panels and assemblies inside your appliance. Replacing missing or damaged hardware restores a tight, rattle-free fit and helps maintain proper alignment of parts.

• Fastens appliance components using an M5 x 0.8 machine-thread
• Replaces missing, loose, or stripped screws
• Helps reduce vibration and rattling noises
• Maintains correct alignment of brackets, panels, or internal assemblies

• Disconnect power before servicing; if working near water connections, shut off the supply.
• Match thread and length to the original screw and replace in the same location.
• Start threading by hand to avoid cross-threading; use the correct driver and do not overtighten.
• Reinstall any original washers or lock hardware used with the screw.

This replacement hose routes water within your washer. Replacing a cracked, worn, or leaking hose restores a secure, watertight path so the machine can move water properly without puddles or performance issues.

• Transfers water between internal components during wash cycles
• Maintains a sealed flow path to help prevent leaks
• Damage may present as water on the floor, moisture under the unit, or related fill/drain errors
• Cracks, swelling, abrasion, or loose connections are common failure signs

• Unplug the washer and turn off water supply; have towels or a pan ready for residual water
• Note hose routing and clamp positions before removal; photos can help
• Transfer or replace clamps as needed; seat connections fully and secure firmly
• Run a test cycle and check all connections for leaks

This component is a drive motor that is made specifically for washing machines. The drive motor is what spins the tub and drives the agitator.If the washing machine fails to start or makes strange noises, it could be the drive motor that is causing the issue. Other signs that this part is faulty are if the washing machine fails to fill with water, agitate, spin, or drain. An error code reading “E57”, “E58”, “E59”, or “srv cll” may also appear on the digital display. Make sure to disconnect the appliance from its power source prior to attempting to replace this part. Whoever is performing the replacement may choose to wear gloves to protect their hands during this process.This drive motor is compatible with washing machines that are manufactured by Whirlpool, Kenmore Elite, Electrolux, Frigidaire, Crosley, and Kenmore. It is sold individually and sourced from the manufacturer itself.

This clamp secures a hose to its fitting, maintaining a tight, leak-resistant seal at the connection. Replace a fatigued or missing clamp to help prevent drips and stop hoses from working loose under vibration.

• Holds a hose firmly on a pump, tub, dispenser, or valve outlet
• Maintains clamping force to help minimize leaks at the joint
• Helps keep hoses from slipping off during operation
• Common signs: water at a hose joint, loose/slipping hose, damaged or corroded clamp

• Disconnect power and shut off water supply before servicing
• Place a towel or pan to catch residual water at the connection
• Note hose position; remove the old clamp, seat hose fully on the fitting, position the new clamp over the bead, and secure
• After reassembly, run a short cycle and check for leaks

This replacement cover restores the protective barrier and finished look of the original part. It shields the underlying assembly from dust and accidental contact, helping maintain safe operation and a clean, factory appearance.

• Provides a protective barrier over the designated opening or component
• Helps maintain proper airflow/enclosure integrity as designed
• Secures with existing tabs or screws for a stable fit
• Typical signs of failure: cracked or missing cover, broken tabs, loose/rattling panel, visible damage

• Disconnect power before service; for laundry appliances, also shut off water and gas
• Wear gloves; retain and reuse original screws/clips unless new hardware is supplied
• Note orientation before removal and transfer any clips, seals, or trim from the old cover
• Seat fully and avoid overtightening; verify clearances before restoring power

10-inch heating element that restores proper heat production in affected appliances. Replaces a worn or failed element to help resolve issues like no heat or unusually long cycle times. What it does:

• Generates heat so your appliance can reach normal operating temperatures.
• Common symptoms it addresses: little or no heat, longer-than-normal cycles, or intermittent heating.
• Replaces a single failed element to return consistent heating performance.

What's included: One heating element. Install notes:

• Disconnect the appliance from power before attempting any repair.
• Allow the element to cool and handle carefully to avoid bending or damaging the coil.
• Ensure the terminal connections are secure and free of corrosion; tighten or replace fasteners as needed.

NOTE: IF THERMISTOR HAS TERMINALS WIRE HARNESS HAS TO BE CHANGED PART# 137288900 PER FRIGIDAIRE

This genuine replacement screw secures appliance components and panels in place to keep your unit assembled and operating smoothly. Use it to replace a missing or damaged fastener so parts stay tight and properly aligned.

• Fastens brackets, panels, or assemblies as designed by the manufacturer
• Helps resolve loose or rattling panels caused by a missing/stripped screw
• Maintains proper alignment after service or repair
• Restores secure mounting when an original fastener is lost or damaged

• Disconnect power (and shut off gas/water if applicable) before servicing
• Use the correct driver to avoid stripping the head
• Start threads by hand to prevent cross-threading; do not overtighten
• Replace any damaged clips or inserts the screw threads into

This machine screw secures panels, brackets, and internal components in compatible appliances. Replacing a missing, rusted, or stripped #10-16 x 3/4-inch screw restores a snug fit and helps keep assemblies properly aligned and quiet.

• Fastens panels, brackets, guards, or other hardware in appliance assemblies
• Replaces lost, corroded, or stripped mounting screws
• Helps reduce vibration and rattling from loose fittings
• Maintains proper alignment and secure attachment of components

• Disconnect power before servicing; turn off gas and/or water supply if applicable
• Note original screw locations and any spacers or clips for correct reassembly
• Start threads by hand to avoid cross-threading; do not overtighten
• Use the appropriate driver or nut driver; wear gloves and eye protection

This main control board assembly is the appliance's electronic "brain," managing timing and power to run cycles. Replacing a failed board can restore normal operation when the unit won't start, won't advance, or behaves erratically. What it does:

• Directs cycle logic and timing for the appliance
• Distributes power to loads (motor, pump, valves, heater as applicable)
• Interprets inputs from sensors and switches and communicates status/errors
• Typical failure symptoms: won't start or power up; no response to controls
• Other symptoms: stuck mid-cycle, unexpected error codes, or components not energizing

• 1 main control board assembly

• Disconnect power from the appliance before servicing; verify no voltage is present
• Handle the board by the edges and use ESD protection to avoid static damage
• Photograph wire connections and move connectors one at a time to the same locations
• Ensure all connectors are fully seated and the board is secured before restoring power

This UI board assembly replaces the refrigerator's user interface/control board to restore button response and display feedback. It lets you reliably set temperatures and modes so the appliance accepts and shows commands correctly. What it does:

• Receives and processes user inputs from the control panel (buttons/touchpad) so selections register and run.
• Drives the front display and indicator lights so temperature, mode and status information is visible.
• Replaces a failed or intermittent interface that causes unresponsive controls, blank or garbled display, or incorrect status indications.
• Works with the main control to pass commands; replacing the board can isolate interface-specific failures.

• Disconnect power to the appliance before starting — this part is electronic and may be damaged by live power.
• Take photos of existing wiring and mounting before removal to ensure correct reassembly.
• Handle the board by its edges and avoid static discharge; use anti-static precautions if available.
• Reconnect all plugs securely and test functions before fully reinstalling trim or covers.

This inner oven door glass restores the viewing window and helps contain heat inside the cavity for even cooking. Use when the door glass is cracked, broken, cloudy, or otherwise damaged to restore safe, usable viewing. What it does:

• Replaces cracked, chipped, shattered, or cloudy inner oven door glass.
• Restores a clear view of the oven interior so you can monitor cooking without opening the door.
• Helps maintain the oven's sealed cavity to reduce heat loss during cooking.
• Prevents loose or broken glass from falling into the oven cavity.

• Allow the oven to cool completely and disconnect power before starting service.
• Handle glass with heavy gloves and eye protection; broken glass can be sharp.
• Reinstall or replace any door screws, brackets, or gaskets exactly as removed; follow the oven manufacturer's service instructions.

A replacement flexible hose that routes water between appliance components to restore proper flow and help prevent leaks. Use this hose when a worn or damaged line is causing pooling or reduced water movement. What it does:

• Carries water between internal components
• Replaces cracked, split, or clogged tubing that can cause leaks
• Helps stop water pooling under or around the appliance
• Can resolve weak or intermittent water flow caused by damaged tubing

• Disconnect power and shut off the water supply before you start
• Inspect routing to avoid kinks; secure with proper clamps or brackets
• Tighten connections evenly and check for leaks after restoring power/water