Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
This high limit thermostat is a safety device that monitors the temperature inside the dryer and cuts power to the heating element if the temperature exceeds a safe threshold. It is typically mounted on the heating element housing or exhaust duct. Replace this thermostat if the dryer is not heating at all or if it overheats - a tripped high limit thermostat often indicates a clogged vent or restricted airflow that should also be addressed.
My Electrolux Frigidaire Gas Dryer stopped working and I got an error code E66 that the thermal limiter blew from over heating. The E66 code stops displaying after the initial code and you will then get a door open message. I replaced the thermal limiter and the thermostat just to be sure which part at the problem. The job is hard because you have to take apart the entire dryer and remove the drum. Would be a tough project to complete on your own. Read more
Replacement air duct assembly with mesh screen for dryers. Installs between drum and heater. Replace if screen is burnt, cracked, melted, or missing.
It was easy to find the part on appliance parts pros. Once I found it I studied the diagram and determined that there were 3 screws in the drum that needed to be removed. I disconnected power and then removed 3 interior screws. Once I did that I removed the back cover and removed the single screw on the bottom side of the air duct that held it in place connected to the heat tube. I then reversed disassembly. I want to tell you this is a 2 person job. In order to assemble it you need to... Read more
Fixes steam cycle not working or water not entering drum during steam cycles. Controls water flow into dryer. Moderate DIY repair for steam dryers.
Dryer not heating? A failed igniter is the most common cause. This part ignites the gas burner for heat. Watch the video for step-by-step replacement.
I looked on Appliance Parts Pros. com and read the problems that others had and replacing the ignitor made sense so I ordered one. It came by UPS within 3 days. I watched the video on how to replace it. Everything went easily, except the screw that held the ignitor in place was a philups head screwdriver and I couldn't get a screwdriver into the small space I had to work in so I went to Harbor Freight Tools and bought an inexpensive 90 degree rachet screwdriver for $2.99 and it worked great.... Read more
Idler spring attaches to the idler arm to maintain proper belt tension. Replace if spring is broken, stretched, or missing to restore correct tension.
I encountered a high pitched squeal and loud rumbling. I figured the sounds were likely the rollers despite not matching other sounds on the repair videos for other dryers. The repair video for dryer rollers on AppliancePartsPros.com is of little use until Minute 2:56 because this Electrolux 517 model uses mostly Phillips head screw to fasten the front and top panels in place. You may find one latch at the top front center that holds the top and front panels in place. After unplugging the... Read more
This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.
This is the lint filter assembly that catches lint and debris from clothes during the drying cycle. It slides into the lint filter housing, typically located inside the dryer door or on top of the dryer. Replace this filter if the screen is torn, warped, or clogged beyond cleaning, which can cause longer drying times, overheating, or pose a fire hazard.
Replaced filter. Read more
Adjustable leveling foot installs at the bottom of your appliance to ensure stability and proper leveling. Replace if broken, cracked, or missing.
I determined that it was a problem that occurred during the defrost cycle by resetting the GFCI outlet and forwarding the defrost timer until the defroster came on. Once the defrosting began, the GFCI outlet would reliably trip. I took apart the shielding inside of the freezer and tested the defrosting without the heating element or the thermostat connected. Since that looked good, I tested for proper functionality of the thermostat by removing it, placing it in a working freezer, and checking... Read more
This door switch senses whether the appliance door is closed and signals the controls to run only when it's safe. Replacing a worn or intermittent switch restores dependable starts and proper shutoff when the door opens. What it does:
If your dryer takes too long or clothes stay damp, a worn blower wheel may be blocking airflow. This part restores circulation. Moderate DIY repair.
Fix a dryer that won't shut off automatically or has temperature control issues. This thermistor sensor monitors heat levels for proper cycle operation.
I replaced the thermostat. The bearing on the motor was getting loose, so I changed the motor to. The repair took about 2 hours. There are some good re[air videos on the parts web site. Read more
Secures the dryer motor in proper position for stable operation. Replace if motor shifts, buzzes, or clamp strips out. Confirm fit with your model number.
Replaced clamp with a new one Read more
Fix dryer heating issues with this thermistor temperature sensor. Solves intermittent heat, cycle errors, and poor drying. Easy DIY repair.
Replaced all sensors, limiters, thermistors, thermostat. Works great now. Read more
This factory screw secures appliance components to their mounting points. Replace missing, worn, or stripped hardware to restore a tight fit, proper alignment, and quieter operation across the affected assembly.
Ordered Bake Element, Y04100019 (Whirlpool AP4283614) to replace a broken bake element on my 30-year old Jenn-Air Model S125 Downdraft Slide-in electric range. Received the element very quickly but it had been damaged in shipping. Called AppliancePartsPros to report this and they quickly shipped another element - very easy process. To install the element, I turned off the power to the range, put on rubber gloves (just in case) and removed the two sheet metal crews at the rear of the oven -... Read more
Dryer not heating? A failed igniter won't light the gas burner. This glow-bar igniter heats up to ignite gas during each cycle. Moderate DIY repair.
This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.
Unscrewed the front lower panel ( 2 screws ). Disconnected the pump hose clamp and removed the hose. I loosened the lower back panel and pulled out the drained hose from the rear. Replaced with new hose put back clamp and panels. Very easy Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.