Ewave Microwave Parts

This control panel assembly operates the oven/microwave user interface and display so you can select settings and see status. It replaces a damaged or non-responsive console to restore normal control and feedback. What it does:

• Houses the touchpad/buttons and display used to set cooking modes, time, and temperature
• Sends user commands to the oven/microwave control board so cycles start and change as directed
• Commonly replaces panels that show a blank or flickering display, unresponsive buttons, or garbled characters
• Helps stop erratic behavior caused by cracked faceplates, water damage to the keypad area, or failed front electronics

• Disconnect power at the breaker before removing the old panel to avoid shock or damage
• Handle the assembly carefully; the display and ribbon connectors are delicate
• Keep mounting screws and brackets from the old unit for reuse unless replacements are provided
• After installation, verify all buttons and the display function through a full power-up and basic cycle test

This backsplash assembly is the rear vertical trim panel that finishes the back of a range or stove, protecting the wall and covering control openings for a clean appearance. It restores the oven's original rear fit and look. What it does:

• Covers the rear area of the range to protect the wall from splashes, spills and heat.
• Provides a finished appearance by concealing control openings and wiring access points.
• Helps maintain proper positioning of rear-mounted components that attach to the oven body.
• Useful when the original backsplash is dented, scratched or bent and needs replacement.

• One backsplash assembly as shown

• Disconnect power to the appliance before beginning any work.
• Installation typically requires removing the cooktop or rear screws; keep fasteners for reuse or replace if damaged.
• Use proper lift/handling to avoid scratching the finish; two people may be needed for safe alignment.
• Verify model fit and part number before installation; do not force parts into place.

This tub-bearing split ring is an OEM replacement part designed for GE washing machines. This part measures 2 inches in diameter. It is positioned between the inner and outer tubs to hold the tub bearing inside the outer tub. The Tub Bearing Split Ring not only supports the tub/hub assembly but also ensures smooth operation. 

Symptoms of a bad Tub Bearing Split Ring include:

• Excessive vibration or tub imbalance during spins  
• Loud clunking, knocking or grinding sounds  
• Reduced spin speeds or inability to achieve high RPMs
• Premature tub or bearing wear requiring replacement

Causes can be extended use over time which leads to wear and fatigue of the split ring material. Cracks or breaks can develop, reducing its stability and load-bearing capacity.

This genuine GE replacement part is also compatible with Hotpoint, RCA and some Kenmore front-load models. 

NOTE: For the washer outer tub seal order WH02X10383.

The Knob Clip is an OEM part for GE washing machines and dryers. This small but crucial component is designed to secure the control knob to the appliance's control panel.  

Over time, knob clips can wear out or break due to frequent use or accidental damage. When this happens, the control knob may become loose, fall off easily, or fail to engage the control panel properly, making it difficult to set the appliance to the desired cycle or function.

Symptoms of a bad Knob Clip include:

• The control knob is loose or falls off the panel easily.
• Difficulty in adjusting settings due to a loose knob.
• The knob does not stay in place or slips when turned.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Washer Top is an OEM part for GE washers. It is the upper panel that covers the internal components of the washing machine and provides a flat surface for loading and unloading laundry.

Causes of a bad Washer Top can include physical impact, warping due to prolonged exposure to heat or moisture, or general wear and tear over time.

Symptoms of a bad Washer Top include:

• Visible cracks, dents, or damage to the top panel
• Difficulty opening or closing the lid due to misalignment or warping
• Water leaks around the top area during wash cycles
• Excessive noise or vibration caused by a loose or damaged top

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This thrust washer is a small wear component used in washers to maintain proper spacing and smooth rotation between mating parts in the drive system. Replacing a worn washer helps reduce friction, noise, and premature wear.

• Maintains clearance and alignment between rotating components
• Reduces friction to support smooth agitation and spin
• Helps prevent squeaking/scraping noises and binding during cycles
• Replaces a cracked, worn, or missing washer that can cause excess play

• Disconnect power and turn off water before servicing
• Access the drive/agitator area per your model's service information
• Match the original washer's placement and orientation during reassembly
• Inspect related spacers, bushings, or couplers and replace if worn

The Drain Hose is an OEM part for GE washing machines. It is specifically designed to channel used water out of the washer and into the household drainage system. 

Causes of a bad drain hose can include physical damage from movement or installation, clogging from lint and debris, or degradation of the hose material over time, leading to leaks and inefficiency.

Symptoms of a bad Drain Hose include:

• Water leaking from the back or underside of the washing machine
• Pools of water around the area where the washing machine is installed
• Signs of wear or damage to the hose, such as cracks, holes, or bulging

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.