Faf3801lwo Parts

This is a motor control board for a washing machine. It comes with the board, tape, bracket, and screw mounted on control. In most cases, this part is located on the bottom of the appliance near the drive motor. The purpose is to control the speed of the drive motor. It also works to determine the direction of the tumble and spin actions while a cycle is in process. If the washing machine is pumping but does not spin, this is often the result of a malfunctioning motor control board.If the motor control board has gone bad, it should be replaced. To replace it, make sure the washer is unplugged or the circuit breaker has been turned off. Pull the washer away from the wall, remove the knobs from the front and screws from the back, and lift the control panel. This offers access to the motor control board, which should be removed so the new part can be installed.This motor control board is made for use with washing machines by Electrolux, Frigidaire, Crosley, and Kenmore. It is sold on an individual basis. This is an authentic OEM replacement part that is directly sourced from the manufacturer.

The Tub to Pump Hose is an OEM replacement part for Frigidaire washing machines. This hose connects the tub to the pump, allowing water to be drained out of the tub and into the drainage system. 

Causes for a malfunctioning Tub to Pump Hose can include blockages from lint or small objects, cracks or holes in the hose material, or loosening of the hose clamps that secure it in place.

Symptoms of a bad Tub to Pump Hose include:

• Water leaking from the bottom of the machine
• Slow or incomplete drainage
• Unusual noises during the drain cycle
• Error messages related to water drainage

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Shock Absorber Mounting Pin is an OEM part for Frigidaire washing machines. It is a part that secures the shock absorber in place, ensuring proper absorption of vibrations and shocks during the washing cycle.

Causes of a bad shock absorber mounting pin can include loosening over time due to constant movement and vibrations, accidental damage or loss during repair or maintenance, or general wear and tear.

Symptoms of a bad or missing shock absorber mounting pin include:

• Excessive shaking or vibrating during the wash cycle
• Loud banging or rattling noises
• The washer moving or "walking" across the floor
• Premature wear or damage to the shock absorbers and other components

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Inner Bellow Spring Clamp is an OEM replacement part for Frigidaire front-loading washing machines. It anchors the interior bellow seal in the proper sealing position.

Causes of replacement include torsion fatigue from years of door opening/closing stresses. Mineral buildup may also restrict needed tension if left unchecked.

Symptoms consist of:

• Visible water leakage from the base of the washer door during active cycles
• Looseness permitting shifting or twisting of bellow position
• Inability to achieve proper water-tight integrity checks

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore ranges.

This washer tub-to-pump hose connects the outer tub to the drain pump, carrying wash water out during the drain cycle. Replacing a cracked, clogged, or leaking hose helps stop leaks, restore dependable draining, and prevent water damage.

• Directs water from the outer tub to the drain pump during drain and spin
• Common symptoms: water leaking under the washer, water left in the drum, slow or no drain, or drain-related error codes
• Wear, heat, or debris/foreign objects can cause splits, soft spots, or blockages
• Restores a sealed flow path to improve drainage and reduce leaks

• Unplug the washer and turn off water supply; use gloves and have towels or a shallow pan ready for residual water
• Access the pump area through the lower front or rear service panel (varies by model)
• Note routing/orientation; move clamps back, seat the new hose fully on both fittings, and resecure clamps
• Run a short rinse/drain cycle and inspect all connections for leaks

This rear shock absorber kit stabilizes the washer tub by damping movement and vibration. Replacing a worn shock restores smoother, quieter spins and helps prevent the drum from banging the cabinet or the machine from walking. What it does:

• Dampens tub movement to control vibration during wash and spin
• Helps prevent banging/thumping noises and cabinet contact
• Reduces "walking" or excessive shaking of the washer
• Can help minimize out-of-balance interruptions

• One rear shock absorber kit

• Disconnect power and turn off water before servicing
• Support the tub/drum to relieve load before removing the shock
• Remove retaining pins/bolts; install the new shock in the same orientation and transfer any reusable hardware
• For consistent damping, replacing shocks in pairs or as a complete set is commonly recommended

This washer drive belt links the motor to the drum pulley so the machine can tumble and spin. Replacing a broken or stretched belt restores smooth, reliable drum rotation during wash and spin cycles.

• Transfers motor power to the drum for tumbling and spin
• Worn or broken belts can cause no spin/tumble or intermittent rotation
• Common symptoms: drum won't spin, squealing or thumping noises, burning rubber smell, visible fraying/cracks
• Slipping belt can leave clothes wetter than normal at cycle end

• Disconnect power and turn off water supplies before servicing
• Access the belt from the rear or bottom; remove panels as directed in your model's service information
• Release belt tension at the motor/idler, remove the old belt, and route the new belt over the drum and motor pulleys with ribs properly seated
• Rotate the drum by hand to verify alignment; reassemble and test. Inspect the idler/tensioner and pulleys while open

This front shock absorber kit stabilizes the washer's tub during spin to reduce vibration and noise. Replacing worn dampers helps restore smooth operation and protects the cabinet and suspension from excessive movement.

• Dampens and controls tub movement during wash and spin
• Helps reduce shaking, "walking," and loud thumping/banging noises
• Can help when the washer won't reach or maintain full spin due to imbalance
• Replaces weakened or damaged front shock mounts/dampers

• Disconnect power and water before servicing
• Access shocks per your model's procedure; support the tub to relieve load
• Install with mounts aligned and fasteners tightened securely; verify free tub movement
• Many replace shocks in pairs to maintain balanced damping

The Tub to Pump Hose is an OEM part for Frigidaire washing machines. This part directs water from the tub to the pump during the wash cycle. This flexible hose plays a role in the machine's ability to drain water efficiently after each wash or rinse cycle, ensuring optimal performance. 

Causes for replacement might include wear and tear over time that leads to cracks or holes in the hose, blockages that prevent water from draining properly, or improper installation that results in leaks or water retention. 

Symptoms of a bad Tub to Pump Hose include:

• Leaks found underneath the washing machine
• Problems with the washing machine draining properly
• Puddles of water appearing during or after a wash cycle

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Inner Door Panel is an OEM replacement part for Frigidaire washing machines. This panel forms the inner structure of the washer door, providing a secure enclosure and supporting various components such as the door lock and handle. It plays a key role in ensuring the door seals properly to prevent water leakage during the wash cycle.

Causes of a bad inner door panel can include physical damage from impact or mishandling, warping or cracking due to age, or wear and tear from repeated use.

Symptoms of a bad Inner Door Panel include:

• Water leaking from the door during washing
• The door not closing or sealing properly
• Visible cracks or damage on the panel
• Difficulty in latching or locking the door

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This tub filter screens wash water as it leaves the outer tub, capturing lint and small items before they reach the drain pump. Replacing a damaged or missing filter helps restore proper draining and protect the pump from debris.

• Screens lint, threads, and small debris from water exiting the tub
• Helps prevent drain pump clogs and drain-related errors
• A clogged, damaged, or missing filter can cause slow/no drain, standing water, or pump noise
• Physical damage, broken tabs, or warping are common reasons to replace

• Disconnect power and turn off water; expect residual water—use towels or a pan
• Access location varies by model; the filter sits at the outer tub outlet along the drain path
• Release the hose clamp/retainer, remove debris and the old filter, seat the new filter fully in the port
• Reattach clamps securely and run a short drain/rinse to check for leaks and proper flow

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

The Dispenser to Tub Hose is an OEM part for Frigidaire washing machines. This hose is responsible for transporting detergent and other cleaning agents from the dispenser to the tub during the wash cycle.  

Common causes of a bad hose include constant exposure to water and detergent, which can lead to wear and tear, blockages from detergent buildup, or physical damage such as cracks and splits.

Symptoms of a bad dispenser to tub hose include:

• Water leaks near the detergent dispenser
• Uneven or insufficient distribution of detergent
• Visible cracks, splits, or other damage to the hose
• Error codes on the washing machine related to water flow

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Door Boot Seal is an OEM part for Frigidaire washing machines. It creates a watertight seal between the door and the drum of the washer, preventing leaks during operation.  

Causes of a bad door boot seal can include wear and tear over time, exposure to harsh detergents, or physical damage from sharp objects or heavy loads.  

Symptoms of a bad door boot seal include:

• Water leaking from the door area during wash cycles
• Visible tears, cracks, or mold buildup on the seal
• Unpleasant odors from the washer drum
• Difficulty in closing the washer door properly

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This door switch senses whether the appliance door is closed and signals the controls to run only when it's safe. Replacing a worn or intermittent switch restores dependable starts and proper shutoff when the door opens. What it does:

• Detects door position and allows operation only when the door is fully closed
• Interrupts operation when the door opens for safety
• Common symptoms include: won't start, stops when the door is moved, or "door open" message/error
• Intermittent starts due to worn actuator or internal switch contacts

• 1 door switch

• Disconnect power before servicing
• Access the switch from the front or top panel; release mounting screws or tabs
• Move wires to the new switch one at a time to maintain correct positions, then secure the switch
• Test operation before reassembly

The Leveling Leg is an OEM part for Frigidaire washers. It is designed to provide stability and level the appliance properly on the floor during installation and operation.

Common causes for needing to replace the leveling leg include damage or wear over time, which can lead to unevenness and excessive vibration during wash cycles.

Symptoms that may indicate the need for a replacement leveling leg:

• Uneven or unstable washing machine
• Excessive shaking or vibration during spin cycles
• Difficulty in leveling the washer during installation

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.