Fccf3036tf Parts

This controller is the appliance's electronic control board. It monitors sensors and manages cooling system operations so temperatures stay stable. Replacing a failed board can restore consistent cooling performance and responsive controls.

• Manages compressor and fan run times to maintain the set temperature; failures can cause warm temps, overcooling, or short cycling
• Coordinates automatic defrost on applicable models; faults may lead to frost buildup and restricted airflow
• Processes input from temperature sensors and user settings; issues can make controls unresponsive or erratic
• Drives status lights/alarms on applicable models; malfunctions may trigger false alarms or no indications

• Disconnect power to the appliance before servicing
• Use ESD protection; handle the board by the edges to avoid component damage
• Photograph wiring and move connectors one at a time to the new board to ensure correct placement
• Reuse original mounting hardware and ensure all connections are fully seated before restoring power

This replacement screw secures appliance panels and components. With a #10-16 thread and 0.75-inch length, it replaces stripped, rusted, or missing hardware to restore a tight, rattle-free fit and reduce vibration and noise.

• Fastens cabinet panels, brackets, or internal parts in washers and dryers
• Direct replacement for worn or lost screws to keep assemblies aligned and secure
• Helps address loose/vibrating panels, rattling noises, or visible gaps/misalignment
• Spec: #10-16 thread; 0.75-inch length

• Disconnect power; for washers, also shut off water supply
• Match the original screw location; start threads by hand to prevent cross-threading
• Use a driver that fits the screw head properly; tighten snugly without overtightening

This replacement screw secures appliance components so brackets, shelves, trim, or panels stay firmly in place. Install a new screw when the original is missing, stripped, or corroded to restore a tight, rattle-free fit.

• Fastens brackets, panels, trim, or covers to the cabinet or liner
• Helps maintain alignment and reduce vibration and noise
• Direct replacement for a missing, rusted, or stripped fastener
• Use wherever your model's parts diagram specifies this screw

• Disconnect power before servicing; shut off water if working near water lines
• Match thread and length to the original location as shown in your model's parts diagram
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening (especially into plastic)
• Retain and transfer any original spacers or clips used with this fastener

The product featured is a Frigidaire refrigerator compressor. The compressor is a vital component for the cooling and freezing process of a refrigerator. A compressor works together with the evaporator in providing the cold air needed to keep everything at the desired temperature. When a compressor fails, this could have an effect that calls for an emergency repair. Losing the compressor function means the refrigerator stops getting cold in both compartments. Prolonging the repair could mean the loss of all the food items stored inside. A faulty compressor may become very loud when it operates. Users may hear a slight clicking sound on a compressor that's entirely out of commission. This is the relay clicking in an attempt to power the compressor. If a compressor does go out, keep the doors of the freezer and refrigerator shut. There's a chance the food can be salvaged if repairs take place fast enough. This compressor is a genuine OEM product and is sourced directly from the manufacturer and is only available as an individual component. Frigidaire, Kenmore, and Maytag refrigerators can be repaired with this component.

This hinge assembly supports and pivots the appliance door so it opens smoothly and closes squarely against the gasket. Replacing a worn or bent hinge restores alignment and helps maintain a reliable seal and temperature performance. What it does:

• Provides the pivot point and support for the door
• Helps keep the door level for proper gasket contact
• Can help resolve door sagging, rubbing, or binding
• Can help with doors that won't fully close or pop back open
• Addresses play, squeaks, or visible hinge damage

• One hinge assembly

• Disconnect power and support the door before removing hinge fasteners
• Note and transfer any shims/spacers from the old hinge to the new one
• Reuse existing hardware unless the manufacturer specifies otherwise
• After installation, verify door alignment and full gasket contact; adjust as needed

Quantity of 1 clip.

Note: See kit# 5303922007 and 5304406520.

This genuine replacement cap restores a clean, finished look and helps protect the underlying fastener or opening on your appliance. Replace a missing or damaged cap to keep components covered and looking factory-fresh.

• Covers and protects an exposed screw, hinge, or opening from dust and debris
• Restores the appliance's finished appearance
• Helps maintain secure retention of the underlying component
• Common signs of failure: missing or broken cap, cap won't stay in place, cosmetic wear, visible exposed fastener/opening

• Disconnect power before servicing; if working near water or gas lines, shut those off as applicable
• Gently pry off the old cap; avoid scratching surrounding surfaces
• Align and press the new cap until it seats/snaps securely

This temperature control thermostat regulates cabinet temperature by cycling the cooling system on and off. It helps your appliance hold the setting you select so food stays cold without unnecessary overcooling.

• Senses internal temperature and opens/closes electrical contacts to start or stop the compressor
• Maintains the setpoint chosen with the control knob
• Symptoms of a failing control include: too warm or too cold temperatures
• Runs constantly or won't run unless tapped/adjusted
• Temperature knob has little or no effect on cooling

• Disconnect power before servicing
• Note wire locations and take photos before removal
• Route the sensing capillary/bulb exactly as original; do not kink or sharply bend it
• Secure the sensing bulb in its clips and ensure good contact; set to mid-range and allow up to 24 hours for temperatures to stabilize

This hinge assembly provides the pivot and support for your freezer door or lid, allowing smooth opening and secure closing. Replacing a worn hinge restores alignment and helps the gasket seal to keep cold air contained.

• Supports and pivots the door/lid during opening and closing
• Maintains alignment so the door/lid closes fully and seals properly
• Can help resolve sagging, binding, scraping noises, or doors not closing all the way
• Replaces a bent, cracked, or seized hinge assembly

• Disconnect power before service; wear gloves.
• Support the door or lid and use a second person to prevent drops or damage.
• Transfer any spacers, bushings, or covers from the old hinge if required.
• Align the hinge, tighten fasteners, and verify smooth operation and gasket seal.

Color: White

This compressor starter engages the start windings so the refrigerator/freezer compressor can begin running. When the starter fails, the compressor may not start, leading to warm temperatures and clicking or brief humming from the compressor area.

• Provides a brief, high-current assist to the compressor's start winding to initiate operation
• Automatically disengages after startup so the compressor runs normally
• Common symptoms of a faulty starter: compressor won't start, repeated clicking, brief hum then stop, little or no cooling
• Helps prevent repeated, hard start attempts that can stress the compressor

• Disconnect power before servicing; wear appropriate PPE
• Access the machine compartment; note wire positions/orientation before removal
• Pull the old starter straight off the compressor pins; seat the new starter fully and reconnect wiring
• Avoid stressing refrigerant tubing; discharge it per safe procedures

This machine screw secures panels, brackets, and internal components in compatible appliances. Replacing a missing, rusted, or stripped #10-16 x 3/4-inch screw restores a snug fit and helps keep assemblies properly aligned and quiet.

• Fastens panels, brackets, guards, or other hardware in appliance assemblies
• Replaces lost, corroded, or stripped mounting screws
• Helps reduce vibration and rattling from loose fittings
• Maintains proper alignment and secure attachment of components

• Disconnect power before servicing; turn off gas and/or water supply if applicable
• Note original screw locations and any spacers or clips for correct reassembly
• Start threads by hand to avoid cross-threading; do not overtighten
• Use the appropriate driver or nut driver; wear gloves and eye protection

This compressor mounting clip secures the compressor to its chassis to reduce movement and noise for reliable operation. It replaces worn or broken clips that allow the compressor to shift during use. What it does:

• Holds the compressor in place on the mounting bracket to prevent shifting
• Reduces vibration and rattling noises caused by a loose mount
• Helps maintain proper compressor alignment for steady operation
• Useful when a cracked or bent clip no longer secures the compressor

• Disconnect power to the appliance before accessing compressor area
• Inspect surrounding mounts and rubber isolators; replace if damaged
• Secure clip fully so compressor is held without forcing or misaligning components

Note: Quantity of two brackets

This replacement cap covers and protects a small opening or fastener on your appliance. It restores a clean, finished appearance and helps keep out dust and moisture when the original cap is missing or damaged. What it does:

• Covers a screw hole or open end as designed on the unit
• Helps block debris and moisture and can reduce rattles
• Maintains a clean, finished look and protects underlying hardware
• Replace if the original cap is cracked, loose, deformed, or missing

• 1 cap

• Disconnect power and allow any hot surfaces to cool before servicing
• Use a non-marring tool to gently remove the old cap to avoid scratching
• Align and press/snap the new cap into place; do not force
• If the cap conceals a fastener, the fastener is secure before reinstalling the cap

This replacement cap covers and protects its designated opening or fastener on your appliance. It restores a clean, finished look and helps shield internal areas from dust and wear when the original cap is missing or damaged. What it does:

• Covers a specific opening, fastener, or trim end to protect the area
• Helps keep moisture, grease, and debris out of the assembly
• Restores proper fit and finished appearance
• Typical symptoms include a cracked, loose, discolored, or missing cap

• 1 cap

• Disconnect power and, if applicable, shut off gas/water before servicing
• Note the cap's orientation; gently unclip, pry, or unthread the original per model design
• Seat the new cap fully and avoid forcing or overtightening
• The cap is secure and does not interfere with moving parts