Ffle3900uwo Parts

The Lock is an OEM part for Frigidaire washers, designed to securely close the door. The mechanism engages at the start and releases at the cycle's end or pauses for drum access. Over time, it may wear out or malfunction, jeopardizing appliance safety and function.

Causes of a bad lock can include mechanical wear and tear from regular use, electrical faults within the lock mechanism, damage from forceful closing or opening of the washer door, and corrosion or buildup affecting the lock's components.

Symptoms of a bad Lock include:

• The washer door won't lock or unlock
• The washing machine fails to start a cycle due to the door not being securely locked
• An error code appears on the washer's display indicating a door lock issue
• Unusual noises from the door area when attempting to start a cycle

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This metal bracket supports the drum bearing at the rear of the dryer, helping to hold the drum in proper alignment as it rotates. It provides a stable mounting point for the bearing assembly that the drum rides on. Replace this bracket if the dryer makes squealing, grinding, or thumping noises during operation, or if the drum wobbles and does not spin smoothly.

Washer not draining or water remains in tub? This drain pump assembly removes water between cycles. DIY repair typically takes 30 minutes to install.

Dryer door won't stay closed? The door strike secures the door latch during operation. Quick DIY fix—installs from the front in minutes.

This washer agitator drives the wash action by moving clothes through water and detergent. Replacing a worn, cracked, or slipping agitator restores proper turnover and cleaning performance in compatible top-load machines.

• Oscillates during the wash cycle to move laundry through water and detergent
• Helps circulate and distribute clothes for effective cleaning
• Engages the drive hub; wear can cause slipping or poor agitation
• Helps resolve: no/weak agitation, agitator not moving, poor cleaning results, or visible damage/looseness

• Disconnect power and shut off water before servicing; work inside the washer basket
• Remove the fabric softener dispenser and inner cap, then the agitator retaining bolt; lift the agitator straight up
• Align splines and seat the new agitator fully; reinstall and tighten the retaining bolt, then reinstall the cap/dispenser
• After reassembly, run a short cycle to ensure proper engagement and operation

This is a small metal grounding ball that sits in the rear drum bearing area of the dryer. It helps dissipate static electricity buildup in the drum during operation. Replace this part if you are experiencing excessive static cling on clothes, static shocks when unloading laundry, or if the original ball is missing or worn.

The Board Assembly is an OEM part for Frigidaire dryers. This circuit board is for the electronic functions that control drying cycles, settings, sensors, and input/output components.

Causes of a bad board assembly include physical damage from impact or handling, short-circuiting due to intrusion of foreign materials, or naturally occuring component degradation as electronics age. Environmental exposures like moisture over prolonged use can corrode circuitry.

Symptoms of a bad board assembly can include:

• Non-functional cycles
• Inability to select options
• Failure to advance through sequence
• Unresponsive controls/display 

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This is the user interface control board for the washer section of a laundry center. It manages the display panel and button inputs, allowing you to select wash cycles, settings, and start or pause the machine. Replace this board if the washer display is blank, unresponsive, shows error codes, or if button presses are not registering properly.

Fix a laundry center that won't start cycles or shows error codes with this main control board. Requires removing panels to access. Compatible with washer dryer combos.

This washer door lock secures the door closed and communicates locked status to the control so cycles can run safely. Replacing a failed lock restores proper latching and may resolve no-start, spin, or door/lock error issues.

• Locks the door at the start of the cycle to prevent opening during wash and spin
• Signals the control when the door is closed and locked
• Releases the door at the end of the cycle
• Common symptoms: won't start, door won't lock/unlock, intermittent pauses, door/lock error message

• Unplug the washer before servicing
• Access the lock from the front; remove the door gasket clamp and mounting screws (procedure varies by model)
• Transfer wires to the new lock one connector at a time; do not force terminals
• Verify the door striker engages smoothly and test an empty cycle before full use

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

Washer won't start or door won't close properly? This door striker secures your laundry center lid. Simple 2-screw replacement takes 10 minutes.

Dryer won't start or stops mid-cycle? This door switch detects when the door is closed, allowing your dryer to run. Simple DIY fix in 15-30 minutes.

This factory clamp secures a hose or tubing connection so it stays tight during normal operation. Replace a worn or rusted clamp to restore a firm hold and help prevent leaks, drips, or accidental disconnections.

• Holds a hose, tube, or duct firmly to its fitting
• Helps maintain a sealed connection under vibration
• Helps resolve loose connections, drips/moisture at a joint, or rattling noises
• Common wear includes loss of tension, corrosion, or visible damage

• Disconnect power; if servicing a water line, shut off the water supply
• Note the original clamp position and orientation before removal
• Use appropriate hand tools (pliers, screwdriver, or nut driver as applicable)
• After installation, test for leaks or movement

For a complete drum bearing and shaft kit order 5303281153.

Fix excessive shaking, banging, or off-balance errors caused by a broken suspension rod. This tub stabilizer absorbs movement during spin cycles.