Ffle3911qwo Parts

This suspension rod stabilizes the washer tub during wash and spin, absorbing movement to reduce shaking and noise. Replacing a weakened rod restores proper balance and helps prevent banging, off-balance interruptions, and excess wear on other components.

• Supports and centers the tub within the cabinet
• Dampens vibration and tub oscillation during agitation and spin
• Helps prevent the tub from striking the cabinet
• Symptoms of a failing rod can include excessive vibration/shaking, loud banging, "walking," off-balance/UL errors, or wet loads after spin

• Disconnect power and water supply before servicing; wear gloves and eye protection
• Support the tub before removing the rod—spring tension is present
• Access from the top; release the upper retainer, then unhook the lower end from the tub mount
• Install in the same position/orientation as the original; replacing multiple rods together can help maintain balance

For a complete drum bearing and shaft kit order 5303281153.

The Drain Hose Kit is an OEM part for Frigidaire washing machines. It includes all of the necessary tubing to safely drain used water away from the washer during each cycle. 

Causes of a bad drain hose kit can include cracks or splits from continuous bending fatigue, pinch points in drainage routing that compromise integrity over time, or dried-out rubber that becomes brittle and prone to leakage.

Symptoms of a failing kit include:

• Puddles of water accumulating near or under the washer
• Slow or incomplete draining after cycles have finished
• Water leaks at hose connections or along the length of tubing

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This white door handle replaces a cracked, loose, or missing handle. It restores a secure grip so the door opens and closes properly and refreshes the unit's appearance with a clean, factory-color finish.

• Provides the handhold used to open and close the door
• Common fix for a broken, cracked, or missing handle
• Helps when the handle feels loose, flexes, or falls off
• Restores the door's look with a matching white finish

• Disconnect power before servicing.
• Support the door while removing/installing the handle to prevent stress on hinges or glass.
• Remove the original mounting screws, align the new handle, and reinstall using existing hardware.
• Do not overtighten screws to avoid cracking the handle or door panel.

This electronic control board is the dishwasher's brain, managing cycle logic and communication between the controls and internal sensors. Replacing a failed board can restore responsive controls and consistent, start-to-finish wash performance. What it does:

• Coordinates the dishwasher's operating logic and cycle progression
• Receives inputs from the user interface and door latch and relays commands
• Monitors for faults that trigger beeps or error indications
• Symptoms include no power or no start, unresponsive/intermittent controls, random resets, or stopping mid-cycle

• 1 electronic control board

• Disconnect power at the breaker before service; verify no voltage is present
• Protect the board from static discharge; handle by edges and connector housings
• Document wire/connector positions and transfer them one at a time to the new board
• Access location varies by model (console or base); if your model uses configuration switches/jumpers, match settings to the original per the service sheet

This sensor monitors appliance conditions and relays a signal to the control so heating, cooling, or cycle functions occur at the right time. Replacing a failing sensor restores accurate feedback and more reliable operation.

• Detects operating conditions and sends signals to the control board
• Helps regulate heating/cooling output or cycle timing
• Common symptoms of a failed sensor: erratic operation, incorrect readings, cycles that won't start/finish, or related error codes
• Restores proper control feedback when the original is damaged or out of range

• Disconnect power to the appliance before servicing
• Access the sensor per your service manual; note wire colors/orientation and connector locks before removal
• Transfer any mounting clips or brackets from the original if required
• After installation, run diagnostics or verify resistance/continuity per the tech sheet to confirm proper operation

The Motor Mounting Clamp is an OEM part for Frigidaire dryers. This clamp secures the motor in place within the dryer, ensuring it operates smoothly and remains stable during the drying cycles. The motor mounting clamp is essential for maintaining the proper alignment and function of the dryer motor.

Over time, the motor mounting clamp can become worn out or damaged due to constant vibration and movement. Accidental impacts or mishandling during maintenance can also cause the clamp to fail, leading to motor misalignment or instability.

Symptoms of a bad motor mounting clamp include:

• Excessive noise or vibration during the drying cycle
• Motor shifting or moving within the dryer
• Reduced drying efficiency
• The dryer not starting or stopping abruptly

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The blower housing seal is a perimeter gasket that closes the gap between the blower housing and the adjoining duct or bulkhead. It keeps airflow contained for efficient operation and helps prevent air leaks and debris from escaping.

• Seals the blower housing joint to minimize air leakage
• Helps maintain proper airflow for consistent performance
• Reduces dust/debris escape into the cabinet or surrounding area
• Replaces torn, brittle, flattened, or missing seals that can cause weak air output or rattling

• Disconnect power; turn off gas supply before servicing.
• Access the blower housing; note the original routing/orientation of the seal.
• Remove the old seal and clean mating surfaces of lint and residue.
• Seat the new seal evenly with no gaps or twists; reassemble and verify airflow.

Keep your dryer tumbling smoothly by restoring proper belt tension. This idler spring attaches to the idler arm and maintains tension on the drive belt so the drum turns reliably without slipping or squealing. What it does:

• Applies constant tension to the idler pulley to keep the drive belt tight around the drum and motor
• Helps resolve a drum that won't turn or tumbles intermittently
• Addresses belt issues such as slipping off, appearing loose, or premature breakage from low tension
• Can reduce squealing/chirping from the idler area caused by belt slip

• 1 idler spring

• Disconnect power; for gas dryers, also shut off the gas supply
• Access the idler assembly by removing the front or lower access panel per your model
• Relieve belt tension, unhook the old spring from the idler arm/frame, and install the new spring in the same orientation and holes
• Rotate the drum by hand to check smooth operation before reassembly

This replacement housing is the body that holds the washer's detergent drawer and channels rinse water through each compartment into the tub. Replacing a cracked or warped housing restores proper dispensing and helps prevent leaks at the dispenser area.

• Supports and aligns the detergent/bleach/softener drawer
• Routes incoming water to flush each compartment into the wash tub
• Interfaces with inlet hoses and outlet chute for proper flow
• Common symptoms: water leaking from the dispenser/front panel, detergent or softener left in the drawer, poor dispensing, drawer difficult to open/close

• Disconnect power and shut off water supply before servicing
• Remove necessary panels/trim, pull out the drawer, and release mounting screws/clips to access the housing
• Label and disconnect hoses; note routing. Transfer any reusable siphon caps, seals, and the drawer from the original housing
• Reassemble, restore water and power, and run a test fill to check for leaks

A replacement mounting screw used to fasten panels and components in compatible Frigidaire appliances. Replacing a missing or damaged screw restores secure fastening, reduces vibration/rattling, and helps keep parts aligned for reliable operation. What it does:

• Secures panels, trim, brackets or small components to prevent movement and rattling
• Replaces missing, stripped, or damaged fasteners that can cause loose or misaligned parts
• Helps maintain proper fit and finish of appliance panels and access covers
• Useful when a loose screw causes vibration noise or minor part movement

• Unplug the appliance or shut off power at the breaker before servicing electrical appliances
• Use the correct screwdriver or bit to match the screw head to avoid stripping
• Start threads by hand, then tighten until snug; avoid overtightening which can strip threads or crack plastic
• Keep small parts away from children and retain any removed hardware for reuse

A replacement bracket screw used to fasten internal brackets and panels to the appliance frame, restoring secure mounting and reducing rattling or misalignment caused by stripped, corroded, or missing fasteners. What it does

• Secures mounting brackets, panels or trim to the appliance chassis.
• Restores proper alignment and prevents movement or vibration-related noise.
• Use when the original screw is stripped, rusted, broken, or missing.
• Square-drive head provides a reliable engagement for positive tightening.

• Disconnect power to the appliance before servicing to avoid electrical hazard.
• Use the correct square (Robertson) driver to avoid cam-out and head damage.
• Tighten until snug; avoid over-tightening which can strip threads or crack panels.
• If threads are damaged, replace with the matching screw size and type or repair threads before reuse.

This plug covers an unused opening on the appliance cabinet or panel to restore a clean, finished look. Replacing a missing or damaged plug helps keep dust and lint out of the cabinet and can reduce vibration-related rattles. What it does:

• Covers an open hole on the cabinet or panel after service or manufacturing access
• Helps block dust and lint from entering the cabinet
• Restores appearance and can eliminate small buzzes/rattles from open gaps
• Replaces a lost, cracked, or loose plug

• One plug

• Disconnect power to the appliance; for washers, also turn off the water supply
• Align the plug with the opening and press or snap it in until fully seated and flush
• Before restoring power and use, ensure the plug is secure

This suspension supports and stabilizes the washer tub, absorbing movement during agitation and spin. Replacing a worn suspension restores balance control to help reduce vibration and noise so the machine runs more smoothly.

• Supports the tub/drum and dampens movement during operation
• Helps reduce shaking, banging, or "walking" during spin
• Can address symptoms like excessive vibration, thumping, and out-of-balance interruptions
• Wear can lead to noisy cycles and increased movement of the tub/drum

• Disconnect power and water before service; use proper lifting/support for the tub or drum.
• Access the suspension mounting points per your model's service/parts diagram.
• Support the tub/drum to remove load before detaching the old suspension; note orientation and hardware.
• Reinstall securely and run a test cycle to confirm smooth operation.

This heater baffle mounts near the heating element to deflect and distribute radiant heat. It helps protect nearby surfaces and wiring while promoting more even temperatures and reliable performance inside the appliance.

• Directs and diffuses heat from the element to reduce hot spots
• Acts as a heat shield to protect the liner and adjacent components from direct radiant heat
• Helps maintain proper clearance and airflow around the element
• Damage or a missing baffle can lead to uneven temperatures, localized discoloration/scorching, or a burning smell

• Disconnect power at the breaker or unplug the appliance; allow it to cool completely
• Access the heater area; remove the screws or clips securing the existing baffle and retain the hardware
• Position the new baffle in the same orientation; ensure it does not contact the heating element
• Restore power and test operation

This factory electrical switch opens and closes a control circuit inside select laundry appliances. Replacing a worn or failed switch restores consistent signaling so the assigned function operates reliably and the machine responds as expected.

• Opens/closes electrical contacts when actuated by the appliance's control, lever, or mechanism
• Provides the on/off or position signal needed by the timer or electronic control
• Common symptoms of a failing switch: no response when selecting an option, intermittent operation, or an option that engages only when wiggled
• May trigger a related fault or cause the cycle to pause/stop when the switch is moved, depending on model

• Disconnect power before servicing; also shut off gas supply
• Access the switch per your model's service information; avoid pulling on wires
• Note and transfer wire positions one-by-one (take a photo for reference)
• If diagnosing, verify switch continuity with a multimeter before and after replacement