Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Secures the dryer motor in proper position for stable operation. Replace if motor shifts, buzzes, or clamp strips out. Confirm fit with your model number.
Replace idler, motor mounting clamp and lock Read more
Washer motor won't start or stops mid-cycle? This motor start capacitor stores electrical energy to start your washer motor. Moderate DIY repair.
I found your site which was most helpful. I saw on your forum, that others had replaced a motor & capacitor with + results. I was willing to spend what I thought was a reasonable amount & your guarantee was the clincher. I knew that if I called the appliance store where we had purchased the washer in 1998, it would be very expensive & even more important, it would take many days as they would have to order the part & then schedule a service call. I installed the motor & capacitor & was... Read more
This gasket is a sealing component used in select appliances. It fits between two mating parts to keep water or air where it belongs, helping prevent leaks and ensuring proper performance. What it does:
This was more maintenance than a fix. I replaced the door gasket and temp sensor on my dryer. Thought what the heck and it might work more efficiently. I also replaced the shocks on my front loading washer. That was a bit of a chore, but could not have done it without the video that showed how to replace them. The socket was the life saver. All is working just fine. Who knows maybe I'll get another 20 year out of them. Read more
White door handle for laundry center dryer door. Replaces cracked, loose, or missing handles. Restores secure grip for opening and closing the door.
Ordered a new handle from appliancepartspros.com and installed. Read more
This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.
Unscrewed the front lower panel ( 2 screws ). Disconnected the pump hose clamp and removed the hose. I loosened the lower back panel and pulled out the drained hose from the rear. Replaced with new hose put back clamp and panels. Very easy Read more
Dryer won't start or smells like burning? A melted or loose terminal block where the power cord connects is often the cause. Easy 20-minute repair.
Let me tell you that the videos made by AppliancePartsPros.com are what I needed most. They are simplified and complete. It turned out that because of a loose connection at the power terminal block, it over heated, melting the block and of course frying the wiring and distorting the connections. The erratic power supply must have damaged the control board. I ordered the terminal block and control board and although a little time consuming for a rookie, I got it working first time. I actually... Read more
Gas smell during or after cycles? Dryer won't heat? Replace the gas valve assembly to restore proper gas flow and safe operation. Advanced repair.
Frigidaire Gallery gas dryer from maybe 15 years ago. Based on the fact the the smell was only in the dryer, I concluded it must be the gas valve failing to completely seal when closed. After looking at the insides again, I suppose it is possible that it was a connection near the burner, but that stuff had remained untouched for 10 years so I still think I made a good assumption. I got a new ignitor as well since I was in there, and compared to the valve, it was cheap! I thought I could get in... Read more
Secures the washer's inner basket to the drive hub, keeping the tub centered and stable during spin. Replace if cracked, corroded, or bolts are damaged.
The seal at the bottom of the tub had started to fail. On large loads water would leak so I ordered a new one rubber seal. Getting the trunnion off the transmission shaft was hard as it was calcified and corroded. I used a wire brush to get some of it off and then used a lot of WD-40. The bolt holding the trunnion plate on sheared off when I tried to remove it on one side and the other came out ok (the bolt hole through the trunnion is not threaded so it should slide out once the plate is off... Read more
Connects washer outer tub to drain pump, channeling water out during drain cycle. Replace if cracked, leaking, deteriorated, or damaged by pests.
Simply open the top of the washer by inserting a putty knife (watch YouTube ) and then the front panel by removing two bottom philips head screws on the front. The whole front panel comes right off. Using pliers the spring clams holding each hose, they come off and each hose is replaced. The drain one was only leaking but since it has open I changed both and even the drive belt. Whole job less than 1 hour. BTW parts arrived next day! Read more
This air duct seal creates a tight barrier between the dryer's lint housing and cabinet. Replacing a worn seal helps prevent air leaks, maintain proper airflow through the lint filter, and restore consistent drying performance.
Pulled front cover off of dryer and back plate to get belt on. Remember to always shut breaker off to machine and test to make sure no electricity is running to it. Pretty simple. I also replaced the seal to the air duct where the lint filter sits since I had to take the front the off anyway. About 1 hr of time to complete and I'll be 60 years old this month. Good thing I didn't have to pull the drum. Read more
Water leaking into the tub or not filling properly? This inlet valve controls water flow into your laundry center. Moderate DIY repair—about 1 hour.
Removed some screws, opened the top of the wash machine, unplugged some wires to remove the part, plugged the wires back into the mew part, put the new water valve into place, secured the water valve with the screw, put the top back on the wash machine, and replaced all remaining screws! Real Simple! Read more
Keep your dryer tumbling smoothly by restoring proper belt tension. This idler spring attaches to the idler arm and maintains tension on the drive belt so the drum turns reliably without slipping or squealing. What it does:
Seals between the outer tub and splash guard to prevent leaks during wash and spin cycles. Replace if water leaks from the top of the cabinet. Confirm fit by model number.
I tore into the washer until i found what i thought was the problem which was the upper outer tub splash cover gasket and when i couldnt find one in my town i ordered a new one from u folks and replaced it hoping for the best and was successful. This fix costed me $35 instead of the $400+ for a new washer glad i looked into it instead of discarding it and buying a new one as most may do thanks Read more
This is a factory switch used in the appliance's control/safety circuit. Replacing a worn or failed switch restores reliable signaling so the selected function engages properly and the unit responds consistently to user inputs and status conditions.
I removed two sheet metal screws to remove the panel above the washing machine lid. That exposed four more phillips drive sheet metal screws, after removing those the dashboard control panel is held by two smaller black screws slightly recessed in the lower corners. This allowed the panel to be pulled down from the top, revealing the back of the switch. At this point I took a picture of the wiring connections with my cell phone to make sure I put them on the new switch in the same... Read more
Replacement suspension spring for washer tub support systems. Restores proper tension when original spring is weakened, broken, or causing tub tilt.
Watched a few of your videos and ordered the springs and a insert, and actually got the parts right. I am not a Appliance repair guy but I am retired and I am pretty handy so I thought what the heck. I watched the videos, a lot of common sense, common tools, and plenty of time. My knuckles are busted up and a little blood, but I got it done. Was actually kind of rewarding. Works like a champ. The Videos, ARE AWESOME. Read more
This replacement bolt secures internal components in your appliance. A stripped, rusted, or missing bolt can let parts loosen and vibrate; installing a new bolt restores a tight, stable connection for reliable operation.