Flce7522aw4 Parts

Washer not draining or water remains in tub? This drain pump assembly removes water between cycles. DIY repair typically takes 30 minutes to install.

The Drum Bearing Bracket is an OEM replacement part for Frigidaire dryers. It holds and supports the drum bearing, which allows the dryer drum to spin smoothly during the tumbling and drying cycle.

Causes of failure can be cracking or breaking of the bracket over time due to constant use and stress. Improper installation that puts strain on the bracket may also lead to issues.

Symptoms of a bad drum bearing bracket include:

• Excessive vibration or shaking during operation
• Loud grinding or scraping noises
• The dryer drum not spinning properly or at all
• Premature wear of the drum bearing

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

Dryer drum bearing ball ensures smooth drum rotation. Replace if drum wobbles, squeaks, or won't turn. Confirm fit with your model number before ordering.

The Board Assembly is an OEM part for Frigidaire dryers. This circuit board is for the electronic functions that control drying cycles, settings, sensors, and input/output components.

Causes of a bad board assembly include physical damage from impact or handling, short-circuiting due to intrusion of foreign materials, or naturally occuring component degradation as electronics age. Environmental exposures like moisture over prolonged use can corrode circuitry.

Symptoms of a bad board assembly can include:

• Non-functional cycles
• Inability to select options
• Failure to advance through sequence
• Unresponsive controls/display 

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Fix a laundry center that won't turn on, trips breakers, or has unresponsive controls with this main control board assembly. Moderate DIY repair.

This washer door lock secures the door closed and communicates locked status to the control so cycles can run safely. Replacing a failed lock restores proper latching and may resolve no-start, spin, or door/lock error issues.

• Locks the door at the start of the cycle to prevent opening during wash and spin
• Signals the control when the door is closed and locked
• Releases the door at the end of the cycle
• Common symptoms: won't start, door won't lock/unlock, intermittent pauses, door/lock error message

• Unplug the washer before servicing
• Access the lock from the front; remove the door gasket clamp and mounting screws (procedure varies by model)
• Transfer wires to the new lock one connector at a time; do not force terminals
• Verify the door striker engages smoothly and test an empty cycle before full use

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

This washer agitator drives the wash action by moving clothes through water and detergent. Replacing a worn, cracked, or slipping agitator restores proper turnover and cleaning performance in compatible top-load machines.

• Oscillates during the wash cycle to move laundry through water and detergent
• Helps circulate and distribute clothes for effective cleaning
• Engages the drive hub; wear can cause slipping or poor agitation
• Helps resolve: no/weak agitation, agitator not moving, poor cleaning results, or visible damage/looseness

• Disconnect power and shut off water before servicing; work inside the washer basket
• Remove the fabric softener dispenser and inner cap, then the agitator retaining bolt; lift the agitator straight up
• Align splines and seat the new agitator fully; reinstall and tighten the retaining bolt, then reinstall the cap/dispenser
• After reassembly, run a short cycle to ensure proper engagement and operation

Washer won't start or door won't close properly? This door striker secures your laundry center lid. Simple 2-screw replacement takes 10 minutes.

This factory clamp secures a hose or tubing connection so it stays tight during normal operation. Replace a worn or rusted clamp to restore a firm hold and help prevent leaks, drips, or accidental disconnections.

• Holds a hose, tube, or duct firmly to its fitting
• Helps maintain a sealed connection under vibration
• Helps resolve loose connections, drips/moisture at a joint, or rattling noises
• Common wear includes loss of tension, corrosion, or visible damage

• Disconnect power; if servicing a water line, shut off the water supply
• Note the original clamp position and orientation before removal
• Use appropriate hand tools (pliers, screwdriver, or nut driver as applicable)
• After installation, test for leaks or movement

Dryer won't start or stops mid-cycle? This door switch detects when the door is closed, allowing your dryer to run. Simple DIY fix in 15-30 minutes.

Washer won't spin or clothes stay sopping wet? The actuator motor shifts between wash and spin cycles. Moderately difficult repair for DIYers.

The Heater Assembly is an OEM part for Frigidaire laundry centers. It functions to safely provide the heat necessary for multiple laundry cycle options including both washer and dryer modes. The assembly works through an electric heating element to heat filtered air throughout clothing loads in the combined washer/dryer unit.  

Causes of a failing heater assembly can include cracks or breaks in the coil insulating material allowing short circuits over many uses. Mineral buildup on heating surfaces can reduce heat transfer efficiency as well.

Symptoms of failure include:

• Extended or unfinished dryer-mode cycles  
• Tripping of internal thermal cut-off devices
• Loose, burnt, or cracked wires in the assembly housing
• Abnormal smells or smoke during operation

Compatible models include those by Kenmore, Crosley, and Inglis. 

For a complete drum bearing and shaft kit order 5303281153.

This gasket is a sealing component used in select appliances. It fits between two mating parts to keep water or air where it belongs, helping prevent leaks and ensuring proper performance. What it does:

• Forms a tight seal between components or housings
• Helps prevent water drips, seepage, or air leaks at the joint
• Maintains correct appliance performance by keeping moisture/airflow contained
• Replace if the gasket is cracked, torn, flattened, or misshapen
• Common signs include residue, moisture, or visible gaps around the seal

• 1 gasket

• Disconnect power; turn off the water supply before servicing
• Note the orientation of the old gasket prior to removal
• Clean and dry the mating surfaces; remove any old gasket residue
• Seat the new gasket evenly without stretching; reassemble and check for leaks or proper seal

Fix excessive shaking, banging, or off-balance errors caused by a broken suspension rod. This tub stabilizer absorbs movement during spin cycles.