Fsec748gfs1 Parts

This dryer thermostat monitors internal air temperature and opens/closes the heater circuit to keep drying safe and consistent. Replacing a weak or failed thermostat restores proper heat and helps prevent overheating or nuisance shutdowns. What it does:

• Senses exhaust/heater housing temperature and switches the heating circuit based on temperature
• Helps maintain target drying temperatures for consistent performance
• Provides over-temperature protection by opening the circuit if heat rises too high
• Common symptoms include no heat or weak heat, long dry times, heat cutting out mid-cycle, or the dryer running hotter than normal

• 1 thermostat

• Disconnect power before servicing; heating components can be live and hot
• Access location varies by model; typically mounted on the heater or blower housing behind a rear or front panel
• Transfer wires from the old thermostat to the new one one-at-a-time and secure firmly; ensure the mounting surface is clean and flat
• After replacement, check and clear the venting/duct for proper airflow to prevent repeat failures

This dryer timer controls and advances the cycle you select, routing power to the correct components and shutting the dryer off at the proper time. Replacing a worn timer restores consistent cycle timing and end-of-cycle shutoff.

• Controls cycle selection and duration
• Advances the dial through the program and turns the dryer off at the end
• Routes power to dryer components at the correct times during the cycle
• Signs of a failing timer may include: cycle not advancing, running indefinitely, stopping early, or erratic timing

• Disconnect power; for gas dryers, also shut off the gas supply
• Remove the control knob and access the console to unmount the old timer
• Label or photograph wiring; move terminals to the new timer one at a time to avoid miswiring
• Align the timer shaft with the dial, secure the timer, and test operation before reassembly

This dryer timer is the cycle control that advances your dryer through Timed and Auto Dry settings. Replacing a failed timer restores proper cycle progression, start/stop, and end-of-cycle shutoff.

• Advances the cam and internal contacts to move the dryer through heat, motor, and cool-down steps
• Governs run time on Timed Dry and Auto Dry cycles
• Routes power to the correct circuits in sequence; a failed timer may not advance or may stop early
• Common symptoms include timer knob not moving, dryer running indefinitely, or not starting on certain settings

• Disconnect power; for gas models, also shut off gas
• Remove knob/dial, open the console, and unmount the timer
• Label or photograph wiring; transfer wires one at a time to the new timer
• Reassemble and test both a Timed Dry and an Auto Dry cycle

This gasket is a sealing component used in select appliances. It fits between two mating parts to keep water or air where it belongs, helping prevent leaks and ensuring proper performance. What it does:

• Forms a tight seal between components or housings
• Helps prevent water drips, seepage, or air leaks at the joint
• Maintains correct appliance performance by keeping moisture/airflow contained
• Replace if the gasket is cracked, torn, flattened, or misshapen
• Common signs include residue, moisture, or visible gaps around the seal

• 1 gasket

• Disconnect power; turn off the water supply before servicing
• Note the orientation of the old gasket prior to removal
• Clean and dry the mating surfaces; remove any old gasket residue
• Seat the new gasket evenly without stretching; reassemble and check for leaks or proper seal

The Terminal Block is an OEM replacement part for Frigidaire clothes dryers. It is the part the power cord connects to. This kit includes 3 screws and 3 terminals.

Causes of a bad terminal block can include damage from age, overheating from worn wires or loose connections, or improper installation during manufacturing.

Symptoms of a bad terminal block include:

• The dryer not powering on
• Intermittent heating issues
• Loose, frayed, or damaged wires

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

For a complete drum bearing and shaft kit order 5303281153.

Terminal Size: 1/4 inch. For the 5/16 inch terminal size order 5300622034. This electric dryer heating element restring coil does not include the heater housing insulators 131472100 or the terminal block 3202786.

This dryer control thermostat regulates internal temperature by cycling the heater on and off. Replacing a failed thermostat restores proper, consistent drying temperatures to protect fabrics and improve overall drying performance.

• Monitors exhaust temperature and opens/closes contacts to maintain target heat
• Helps prevent underheating and overheating during drying cycles
• Common symptoms of failure: no heat or low heat, long dry times, runs too hot, inconsistent temperatures
• A sticking thermostat may cause the high-limit safety to trip

• Disconnect power before servicing
• Access location varies by model; typically mounted on the blower or heater housing
• Move wires one at a time from the old thermostat to the new one; ensure tight, secure connections
• After replacement, clean the lint path and verify exterior venting for proper airflow

This small spacer fits on the idler assembly shaft to properly space and align the belt tensioner. Replacing a worn spacer helps keep the drive belt tracking correctly so the drum/tub runs smoothly and quietly. What it does:

• Spaces and centers the idler pulley on its shaft
• Helps maintain proper belt alignment and tension
• Can reduce squeaking or chirping from the idler area
• A worn or missing spacer may let the belt ride off, fray, or stop the drum/tub

• 1 idler spacer

• Disconnect power before servicing; let hot components cool
• Access the idler assembly per your model, relieve belt tension, and remove retaining hardware to slide off the pulley and old spacer
• Install the new spacer in the same location/orientation; reassemble and route the belt correctly
• Rotate the drum/tub by hand to verify smooth belt tracking before restoring power

This replacement screw secures appliance panels and components. With a #10-16 thread and 0.75-inch length, it replaces stripped, rusted, or missing hardware to restore a tight, rattle-free fit and reduce vibration and noise.

• Fastens cabinet panels, brackets, or internal parts in washers and dryers
• Direct replacement for worn or lost screws to keep assemblies aligned and secure
• Helps address loose/vibrating panels, rattling noises, or visible gaps/misalignment
• Spec: #10-16 thread; 0.75-inch length

• Disconnect power; for washers, also shut off water supply
• Match the original screw location; start threads by hand to prevent cross-threading
• Use a driver that fits the screw head properly; tighten snugly without overtightening

Restore visibility inside your appliance. This lamp assembly replaces a damaged or failed interior light so you can clearly see contents when the door opens, helping maintain safe, reliable illumination in the cabinet/drum.

• Provides interior illumination when the door opens or when the control calls for light
• Houses the bulb and makes the electrical connection
• Common symptoms: no interior light, flickering/intermittent light, or heat-damaged/burned socket or housing

• Disconnect power before servicing to avoid electrical shock
• Access the lamp from the interior or service panel per model
• Install a bulb with the correct type and wattage specified for your model
• Test light operation before reassembling panels

A replacement bracket screw used to fasten internal brackets and panels to the appliance frame, restoring secure mounting and reducing rattling or misalignment caused by stripped, corroded, or missing fasteners. What it does

• Secures mounting brackets, panels or trim to the appliance chassis.
• Restores proper alignment and prevents movement or vibration-related noise.
• Use when the original screw is stripped, rusted, broken, or missing.
• Square-drive head provides a reliable engagement for positive tightening.

• Disconnect power to the appliance before servicing to avoid electrical hazard.
• Use the correct square (Robertson) driver to avoid cam-out and head damage.
• Tighten until snug; avoid over-tightening which can strip threads or crack panels.
• If threads are damaged, replace with the matching screw size and type or repair threads before reuse.

This plug covers an unused opening on the appliance cabinet or panel to restore a clean, finished look. Replacing a missing or damaged plug helps keep dust and lint out of the cabinet and can reduce vibration-related rattles. What it does:

• Covers an open hole on the cabinet or panel after service or manufacturing access
• Helps block dust and lint from entering the cabinet
• Restores appearance and can eliminate small buzzes/rattles from open gaps
• Replaces a lost, cracked, or loose plug

• One plug

• Disconnect power to the appliance; for washers, also turn off the water supply
• Align the plug with the opening and press or snap it in until fully seated and flush
• Before restoring power and use, ensure the plug is secure

This locking clip secures the fan/blower housing in place to keep the airflow path sealed and stable. Replacing a worn or missing lock helps eliminate rattles and air leaks for consistent, quiet operation. What it does:

• Secures the fan/blower housing to its mounting points to prevent movement
• Helps maintain a tight seal for proper airflow through the exhaust path
• May correct rattling, vibration, or scraping noises from the blower area
• A loose or missing lock can allow the housing to shift, causing air leaks and reduced performance

• Fan housing lock

• Disconnect electrical power; if applicable, shut off gas supply before servicing
• Access the blower/fan housing by removing the appropriate access panel(s)
• Note orientation, then release and replace the lock; ensure the housing seats fully and evenly
• Clear lint from the area and verify the blower wheel spins freely before reassembly and testing

This drive belt transfers the motor's power to the machine's drive system so the tub or drum can rotate. Replacing a stretched, glazed, or broken belt restores consistent movement and helps eliminate slippage noises and burning-rubber odors.

• Transfers rotation from the motor pulley to the drive/transmission pulley
• Typical symptoms of a worn belt: no spin or weak spin, no agitation, motor runs but tub/drum doesn't move
• Visual signs include cracks, fraying, glazing, or excessive slack

• Disconnect power; turn off water supply before servicing
• Access the belt by removing the appropriate panel; note the belt routing before removal
• Release the tensioner or loosen motor mounts to remove the old belt, then fit the new belt around the pulleys and rotate by hand to seat it
• Confirm proper tracking and clearance before reassembly and test run

This heater baffle mounts near the heating element to deflect and distribute radiant heat. It helps protect nearby surfaces and wiring while promoting more even temperatures and reliable performance inside the appliance.

• Directs and diffuses heat from the element to reduce hot spots
• Acts as a heat shield to protect the liner and adjacent components from direct radiant heat
• Helps maintain proper clearance and airflow around the element
• Damage or a missing baffle can lead to uneven temperatures, localized discoloration/scorching, or a burning smell

• Disconnect power at the breaker or unplug the appliance; allow it to cool completely
• Access the heater area; remove the screws or clips securing the existing baffle and retain the hardware
• Position the new baffle in the same orientation; ensure it does not contact the heating element
• Restore power and test operation