Gld3600l00bb Parts

Restore proper draining with this dishwasher drain pump assembly. It evacuates wastewater at the end of each wash and rinse, helping the tub empty fully so cycles finish correctly and standing water and drain errors are avoided. What it does:

• Drives an impeller to push water from the tub through the drain hose to household plumbing
• Activates during drain segments to clear the tub between and after cycles
• Helps resolve symptoms like water left in the bottom, slow or intermittent draining
• Addresses loud humming or grinding from the pump area and drain-related cycle interruptions

• 1 drain pump assembly

• Disconnect power at the breaker and turn off water before servicing
• Access from the lower front or bottom; place a towel or pan to catch residual water
• Label and unplug the wire connector, release the clamp/retainer, and remove the pump; transfer any model-specific seal or bracket if present
• Seat and align the new pump fully to avoid leaks, reconnect hoses/wires, then test for proper draining

Specs: B-16 HXW 1/2 SS

This replacement part is an upper rack slide, and it is intended for use in different types of appliances. This is a genuine replacement part made by General Electric. This upper rack slide is an important part of many appliances. This particular one is typically found in dishwashers and helps guide the upper rack in and out. This allows the user to have easy access to the rack in order to place and remove dishes before and after the cleaning process. A new upper slide rack might be needed if the current ones are broken or damaged in any way. It is possible that these slides become stripped over many years of use and need to be replaced. If the upper rack is tilted or not sturdy while being slid back inside the main tub, the upper rack slide might be the problem. Be sure the dishwasher is completely empty prior to replacing this part. This is a genuine OEM part and is sourced directly from the manufacturer. This upper arm rack slide is sold individually.

This replacement bracket secures a component to the appliance frame, keeping it aligned and stable during operation. Install it to replace a bent, cracked, or missing bracket and restore a solid, rattle-free mount.

• Provides a rigid mounting point to hold the specified part in place
• Helps maintain alignment to reduce vibration, rubbing, or noise
• Replaces damaged or corroded hardware to restore a secure fit
• Common symptoms: loose or sagging component, unusual vibration/noise, or part shifting out of position

• Disconnect power before servicing; shut off water supply if working near water lines
• Note original orientation and fastener locations; take a reference photo
• Transfer and reuse existing screws/clips as needed; tighten fasteners evenly without over-torquing
• Verify alignment and test operation before final reassembly

Color: light gray. Each prong goes out about 10 inches from the center.

The Dishrack Roller is an OEM part for Frigidaire dishwashers. This part ensures smooth and effortless movement of the dishrack in and out of the dishwasher. These rollers are attached to the sides of the dishrack, ensuring that it can glide easily without sticking or jamming, thus preventing damage to the dishes or the dishwasher itself.  

Causes of a bad Dishrack Roller can include wear and tear from regular use, damage from overloading the dishrack, or degradation of the roller material over time.  

Symptoms of a bad Dishrack Roller include:

• The dishrack sticking or struggling to move in and out
• A noisy operation when pulling the dishrack
• The dishrack tilting or becoming unaligned due to a missing or broken roller

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Lower dishwasher rack roller axle only. Color: White. Measures about 1 inch wide by 1 inch high by a 1/2 inch deep. For Gray color order part number WD35X21041.

This leveling screw adjusts your dishwasher's leveling leg so you can set the cabinet height and get the unit perfectly level. Proper leveling helps the door seal correctly, reduces rocking, and cuts excess vibration and noise.

• Threads into the leveling leg to raise or lower the dishwasher for accurate leveling and stability
• Helps prevent rocking or wobbling and supports proper door alignment and sealing
• Can reduce vibration/noise associated with an out-of-level installation
• Replaces a stripped, bent, or missing adjustment screw to restore adjustability

• Disconnect power and turn off the water supply; protect flooring before adjusting or replacing
• Remove the toe-kick/access panel to reach the adjuster; support the dishwasher's weight before turning the screw
• Start threads by hand to avoid cross-threading; do not overtighten
• After adjustment, verify level side-to-side and front-to-back with a level and recheck door operation

Set of 8 screws and washers.

Includes screws.

This inlet sump is the lower-tub water intake for the circulation system. It channels wash water to the pump and seals the connection, helping prevent leaks and restoring proper wash performance when the original is cracked, warped, or clogged.

• Directs wash water from the tub into the circulation pump
• Maintains a watertight seal at the pump/sump opening
• Common failure symptoms: water leaking from beneath the unit, poor cleaning results, unusual noise from the pump area
• Visual clues: cracks, deformation, or mineral buildup on the sump inlet

• Disconnect power and shut off the water supply before servicing
• Access is typically from inside the tub and/or the bottom; remove lower rack, spray arm, and sump cover as needed
• Transfer existing clamps/seals and inspect gaskets; replace any worn seals for a proper fit
• Seat the sump fully, secure connections, then run a short cycle to check for leaks

This replacement bracket is used in Frigidaire-made dishwashers to secure an associated component or panel. Replacing a broken or missing bracket restores a tight fit, alignment, and stability so parts don't loosen, rattle, or shift during cycles. What it does:

• Provides a rigid mounting point for the connected part or panel
• Maintains proper alignment and stability during operation
• Helps reduce rattling or vibration from a loose component
• Replaces a broken, bent, rusted, or missing bracket

• 1 bracket

• Disconnect power and turn off the water supply before servicing
• Access and mounting location vary by model; refer to your service or installation manual
• Wear cut-resistant gloves; bracket edges may be sharp
• Save and reuse the original screws/fasteners; install in the same orientation and tighten securely

This dishwasher insulation is a sound-dampening blanket that reduces operating noise and helps contain heat and moisture, protecting surrounding cabinetry and restoring performance when the original insulation is missing, torn, or saturated.

• Helps absorb pump/motor and water-spray noise for quieter cycles
• Acts as a thermal and moisture barrier to limit exterior "sweating"
• Replaces damaged, compressed, or waterlogged insulation to restore design sound levels
• Common signs: louder-than-normal operation, visible missing/torn insulation, moisture around the toe-kick or adjacent cabinets

• Disconnect power at the breaker and shut off water supply before servicing; wear gloves.
• Access the insulation by removing the necessary panel(s); document original placement for reference.
• Position the new insulation in the same orientation; keep clear of hinges, wiring, and vent openings.
• Reassemble, secure/level the dishwasher, and run a test cycle to confirm quiet operation with no interference.

This float stem is the vertical rod that links the dishwasher's tub float to the float switch. It ensures the fill valve shuts off at the correct level to help prevent overfilling, leaks, and poor cleaning results.

• Transfers the float's up/down movement to the float switch to stop water intake
• Helps maintain proper water level and protect against overfill-related leaks
• Failure may cause continuous filling/overfilling, low water level/poor cleaning, or a float that binds or feels loose
• Replace if the stem is cracked, warped, or missing

• Disconnect power and shut off water before servicing
• Remove the lower rack, take off the float cap, and lift out the float to access the stem
• From below the tub, detach the stem from the switch/retainer and install the new stem in the same orientation
• Ensure the float moves freely and actuates the switch; run a fill test and check for leaks
• Steps can vary by model.

This hose clamp kit secures the washer's hoses at the pump, tub, or valve connections, helping stop leaks and hose blow-offs. Replace worn or missing clamps to restore a tight, reliable seal during fill, wash, and drain.

• Secures drain, pump, and fill hoses to fittings to maintain a watertight seal
• Helps prevent drips, leaks, and hoses slipping off during vibration
• Replaces clamps that are rusted, stripped, deformed, or missing
• Common symptoms: water leaking at hose joints, loose hose connections, clamp won't tighten
• Useful when installing a new hose, pump, or valve

• Unplug the washer and turn off water supplies; have towels or a pan ready for residual water
• Release and remove old clamps; seat the hose fully over the fitting before installing new clamps
• Tighten evenly and do not overtighten to avoid hose or fitting damage
• Restore power and water, then run a short cycle to check for leaks at each connection

This lower toe plate mounts at the base of the dishwasher's front. It covers the gap beneath the door to protect internal components and restore a clean, finished look when the original kick panel is dented, cracked, or missing.

• Covers the open area beneath the door at the base of the cabinet
• Shields wiring, hoses, and internal components from bumps and debris
• Restores a clean, finished front appearance
• Common symptoms: panel is bent, cracked, loose/rattling, or missing

• Disconnect power to the dishwasher before servicing
• Remove the mounting screws securing the existing toe plate and lift it away
• Position the new panel and secure with the existing hardware; do not overtighten
• Verify alignment and door clearance after installation