Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Washer won't spin or agitate? This drive motor and inverter assembly controls drum rotation during wash and spin cycles. Moderate DIY repair.
Replaced control board and motor inverter assembly. The hardest part was reinstalling the washer belt . Their is a tool but hopefully I will never have to do this again. Read more
Seals the outer tub opening to prevent water leaks during wash cycles. Replace if leaking from top or gasket is damaged to restore clean performance.
Replaced the top cover which came with a new gasket. Easy to fix and works good. Saved me from buying a new machine. Read more
Secures washer hoses at pump, tub, and valve connections to prevent leaks and hose blow-offs. Replace worn or missing clamps for a tight seal. Confirm fit.
The video was very helpful. the hardest part is getting off old rusted parts. I had to use a hacksaw to remove one of the old clamps. I had to open the bottom of the washing machine to remove of the other clamp. Putting the new parts on was easy. Getting everything apart was a challenge. Putting the new parts on was an easy 5 minute job. Read more
These mounting screws secure various internal components within your washing machine. They hold parts like panels, brackets, and mechanisms in their proper positions during wash cycles. Replace if screws are missing, stripped, or causing rattling noises during operation.
I have a 14 year old GE washing machine that had been making a lot of noise while running but had eventually just stopped flat. The agitator and spin cycle would not run. I found this site and made excellent use of all the repair videos to study about my issue. I put in my machine model number and I Immediately was able to start honing in on what my problem could be from website advice about popular repair parts, stories others had shared about their similar machine issues and watching videos,... Read more
Seals between the outer tub and splash guard to prevent leaks during wash and spin cycles. Replace if water leaks from the top of the cabinet. Confirm fit by model number.
I tore into the washer until i found what i thought was the problem which was the upper outer tub splash cover gasket and when i couldnt find one in my town i ordered a new one from u folks and replaced it hoping for the best and was successful. This fix costed me $35 instead of the $400+ for a new washer glad i looked into it instead of discarding it and buying a new one as most may do thanks Read more
Replacement suspension spring for washer tub support systems. Restores proper tension when original spring is weakened, broken, or causing tub tilt.
Watched a few of your videos and ordered the springs and a insert, and actually got the parts right. I am not a Appliance repair guy but I am retired and I am pretty handy so I thought what the heck. I watched the videos, a lot of common sense, common tools, and plenty of time. My knuckles are busted up and a little blood, but I got it done. Was actually kind of rewarding. Works like a champ. The Videos, ARE AWESOME. Read more
This replacement bolt secures internal components in your appliance. A stripped, rusted, or missing bolt can let parts loosen and vibrate; installing a new bolt restores a tight, stable connection for reliable operation.
The seal at the bottom of the tub had started to fail. On large loads water would leak so I ordered a new one rubber seal. Getting the trunnion off the transmission shaft was hard as it was calcified and corroded. I used a wire brush to get some of it off and then used a lot of WD-40. The bolt holding the trunnion plate on sheared off when I tried to remove it on one side and the other came out ok (the bolt hole through the trunnion is not threaded so it should slide out once the plate is off... Read more
This locking clip secures a mating part—often a control knob—onto its shaft on select laundry appliances. Replacing a worn or missing clip restores a tight fit so controls stay in place and operate as intended during use.
Motor control board was flashing 4 times, indicating that the mode shifter had an error. I disconnected the mode shifter's wire from the controller and measured the resistance between the 2 leads with an ohmmeter. Since the reading was infinite, that meant that the mode shifter coil or in-line thermal sensor was electrically open, i.e. bad. As this fix is near a complete tear-down of the washing machine, here are a few tips I discovered. 1) the hub nut is difficult to remove and you need a... Read more
This replacement screw secures appliance panels and components. With a #10-16 thread and 0.75-inch length, it replaces stripped, rusted, or missing hardware to restore a tight, rattle-free fit and reduce vibration and noise.
Like the original. Read more
Spacer that positions and cushions the agitator screw in top-load washers. Replace if worn, cracked, or missing to maintain proper agitator alignment.
The repair guy told me if I have him fix it I should just buy a new one. I like my washer and dryer because it's a combo and takes up little space so I decided to fix it myself. Not sure if I got lucky but appliance parts pros had a video with almost my exact washer which made repair very easy. Read more
Replacement mounting screw that fastens panels and components in laundry centers. Needed when original is missing, stripped, or damaged to restore secure fit.
Read your terms & conditions thanks for having parts available Read more
Plastic housing that secures the drain solenoid to the pump assembly. Replace if cracked, broken, or missing to properly position the solenoid mechanism.
Viewed you video on Youtube.com and saw how easy it was to change out the triple water valve. Job completed and working like a charm now. Read more
Double-style bushing supports the washer lid hinge pin. Replace worn or cracked bushings to restore smooth, quiet lid operation and proper alignment.
Not hard when you have videos and a mechanical background....piece of cake.... Read more
Fix a washer that won't advance cycles, stops mid-cycle, or runs indefinitely. This timer controls cycle sequence and duration. DIY install in 10 minutes.
Replaced with timer and took about ten minutes Read more
Adjustable leveling leg threads into washer base to stabilize cabinet and reduce vibration. Replace if cracked, broken, or missing for proper support.
Took the old leveling legs out and put the new ones in Read more
Replaces a cracked or leaking wash tub to restore water containment and drum support. Fixes leaks, rubbing noises, and vibration. Confirm fit by model.
I ordered a new mode selector and new tub bearing. Upon disassembly, I noticed that the plastic outer tub had actually heated up around the tub bearing and tub seal area, such that the new tub seal did not fit tightly. I ordered a replacement outer tub, and reassembled all the new parts. During assembly, I installed the new tub seal upside down, but recognized it while re-watching the how-to video. I pulled the assembly back off and flipped the seal over, then reassembled it again. I also put... Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.