Gsl25jfpbs Parts

Great site to DIY! Purchased fresh produce drawer railing and parts. Fixed in under 10 minutes. Thanks so much! Read more

Ordered the new shelf from Appliance Parts Pros, which was a genuine OEM part and much less expensive than the GE Store. Lifted the old shelf out, popped the new one in and it was done. two minutes. Read more

The front wheel assembly replacement (WRXO2X12454) was straightforward and easy to do. Took maybe 30 minutes start to finish. The rear wheel assembly (wheel WRO2X10695 and axle WRO1X10604) that was more involved as the original wheel axle is actually a rivet that you have to cut out. 1. I used a vibrating multitool with a carbide blade to cut the axle out. Had to use a pair of vise grips to hold the rivet to keep it from spinning while cutting it. 2. The new axle I drilled a 2mm hole thru the... Read more

Replaced Ice maker very easy. Read more

First I ordered a new ice door seal, spring, and crank, figuring the condensation in freezer and door was caused by ice door not sealing. Turns out the solenoid for the ice door was completely rusted and was the primary cause, if it had been replaced early, it would have saved the dispenser board. What then happened was the moisture in the freezer door damaged the control board rendering dispenser controls inoperative as well as the heater around the dispenser. Now the freezer door is dripping... Read more

Swapped it out for new tube. Take 5 minutes and zero effort. The drain tube will clog with mold. You can clean it out but the tube will clog again despite's you best efforts as the tube wall provide a great habitat. Ordered new tubes to facilitate swap-outs. Old tubes can be cleaned but will recolonize quickly. Read more

Replaced both upper and lower cam risers. Read more

I ordered the heater unit from your website as well as a new evaporator panel gasket and thermostat. Once I removed the evaporator panel from the rear wall of the freezer side, I used a steamer machine I had to melt all the ice which had accumulated, I replaced the faulty heater unit and all is well. By-the-way, I consider your website amongst the very best and easy to use. I appreciate how well your developers and designers created the diagrams/pictures with numbered parts displayed,... Read more

Replaced shelves Read more

Replaced overload and start relay. went through your troubleshooting guide, found my symptoms, watched repair video. repair video is a big help especially when it is the same model as the one you are trying to repair. easy repair. Read more

Ordered replacement parts. Had trouble attaching handle with gasket. Had to look at vege draw to figure it out. Read more

Very easy to replace the trays slide the broken one out, slide the new one in, no problems. Read more

Replacing the roller assembly corrected the problem. The key to replacing the roller assembly is elevating the refrigerator high enough to remove the roller assembly. (1) Raise and secure the refrigerator, (2) remove the metal bar across the bottom of the refrigerator to provide adequate access to the roller assembly (2-screws), (3) remove the roller assembly adjustment screw, (4) pry the roller pivot pin out, (5) pull the roller assembly toward the front of the refrigerator to remove, (6)... Read more

Replaced overload and start relay. went through your troubleshooting guide, found my symptoms, watched repair video. repair video is a big help especially when it is the same model as the one you are trying to repair. easy repair. Read more

I made the right initial move - I went to appliancepartspros.com and located the necessary parts. A video convinced me I could make the repairs myself. The correct parts were easily ordered and arrived quickly. I had no problem installing the parts using the knowledge I gained from the appliancepartspros.com video and the leak was fixed. Read more

Replaced motor and solenoid cube along with dispenser auger. Simply watched video on repair and installation and really had no problem. My refrigerator is so old that one of the holes in the motor did not align properly. Had to drill another hole to mount the motor to the housing, took ten minutes. The ice auger took the longest as I was afraid of breaking the plastic housing trying to get the tabs to release. Had to watch the video twice to make sure I got the blades back in the right order.... Read more