Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
The Dispenser Drip Tray is an OEM part for GE refrigerators. It's placed beneath the water and ice dispenser to catch drips and spills, preventing water from running down the front of the refrigerator or onto the floor. This part not only helps in keeping the dispensing area clean but also minimizes the risk of slip hazards caused by wet floors.
Over time, the dispenser drip tray can become stained, cracked, or warped, affecting its appearance and functionality.
Symptoms of a bad Dispenser Drip Tray include:
This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.
Was an easy swap. Ordered the pieces, got them withing two days. Didn't realize a hair dryer would melt so much of the plastic pieces that I couldn't even see while trying to defrost the water line in the door. Next time it happens I will just empty the freezer and leave the door open for a few hours. Will save me from making this mistake again. Thankfully easy to replace the parts myself and not too expensive. Read more
The Front Roller Assembly is an OEM part for GE refrigerators. It's designed to support the front part of the refrigerator, allowing for smooth and easy movement when you need to shift the appliance for cleaning, maintenance, or repositioning. This roller assembly ensures the weight of the refrigerator is evenly distributed, reducing strain on the floor and making it easier to move the refrigerator without damaging the flooring or the appliance itself.
Causes of a bad Front Roller Assembly can include wear and tear from regular use, damage from moving the refrigerator improperly, or corrosion over time.
Symptoms of a bad Front Roller Assembly include:
Replacing the roller assembly corrected the problem. The key to replacing the roller assembly is elevating the refrigerator high enough to remove the roller assembly. (1) Raise and secure the refrigerator, (2) remove the metal bar across the bottom of the refrigerator to provide adequate access to the roller assembly (2-screws), (3) remove the roller assembly adjustment screw, (4) pry the roller pivot pin out, (5) pull the roller assembly toward the front of the refrigerator to remove, (6)... Read more
Ordered the new shelf from Appliance Parts Pros, which was a genuine OEM part and much less expensive than the GE Store. Lifted the old shelf out, popped the new one in and it was done. two minutes. Read more
The front wheel assembly replacement (WRXO2X12454) was straightforward and easy to do. Took maybe 30 minutes start to finish. The rear wheel assembly (wheel WRO2X10695 and axle WRO1X10604) that was more involved as the original wheel axle is actually a rivet that you have to cut out. 1. I used a vibrating multitool with a carbide blade to cut the axle out. Had to use a pair of vise grips to hold the rivet to keep it from spinning while cutting it. 2. The new axle I drilled a 2mm hole thru the... Read more
First I ordered a new ice door seal, spring, and crank, figuring the condensation in freezer and door was caused by ice door not sealing. Turns out the solenoid for the ice door was completely rusted and was the primary cause, if it had been replaced early, it would have saved the dispenser board. What then happened was the moisture in the freezer door damaged the control board rendering dispenser controls inoperative as well as the heater around the dispenser. Now the freezer door is dripping... Read more
Replaced Ice maker very easy. Read more
Replaced the worn parts. Read more
Swapped it out for new tube. Take 5 minutes and zero effort. The drain tube will clog with mold. You can clean it out but the tube will clog again despite's you best efforts as the tube wall provide a great habitat. Ordered new tubes to facilitate swap-outs. Old tubes can be cleaned but will recolonize quickly. Read more
I ordered the heater unit from your website as well as a new evaporator panel gasket and thermostat. Once I removed the evaporator panel from the rear wall of the freezer side, I used a steamer machine I had to melt all the ice which had accumulated, I replaced the faulty heater unit and all is well. By-the-way, I consider your website amongst the very best and easy to use. I appreciate how well your developers and designers created the diagrams/pictures with numbered parts displayed,... Read more
Fridge not cooling or making clicking sounds? The compressor start relay energizes the start winding to get your compressor running. DIY-friendly repair.
Went to appliance parts Web site looked at the symptoms ordered the suggested parts, my favorite was watching the part repair video, on what the part does and how to install, got the parts the next day, defrosted the fridge 100%, and one by one installed each part what an easy process the video showed exactly where the part was located and how to remove the old and install the new one, now my fridge is working and cooling better than before I saved over $1,400, didn't have to buy a new... Read more
Replaced overload and start relay. went through your troubleshooting guide, found my symptoms, watched repair video. repair video is a big help especially when it is the same model as the one you are trying to repair. easy repair. Read more
Color: white. Measures about 16 inches wide by 2 inches high by 2-1/2 inches deep.
Ordered replacement parts. Had trouble attaching handle with gasket. Had to look at vege draw to figure it out. Read more
Ordered it from appliance parts pros! Great fit and accurate measurements. Read more
Controls the electronic functions of the water and ice dispenser system in your refrigerator door. Mounted behind or near the dispenser panel on the refrigerator door. Replace when the dispenser doesn't respond to button presses, dispenses continuously, or display shows error codes.
I had to replace the Combined Hmi Asm Bk. I watched a video online about how to remove the part and it took around 15 minutes to replace. The new part works great and extremely fast delivery by appliancepartspros.com! Read more
Once I got the part in the mail, I washed it and installed it in less than 2 minutes. Didn't need any tools! Read more