Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
The Front Roller Assembly is an OEM part for GE refrigerators. It's designed to support the front part of the refrigerator, allowing for smooth and easy movement when you need to shift the appliance for cleaning, maintenance, or repositioning. This roller assembly ensures the weight of the refrigerator is evenly distributed, reducing strain on the floor and making it easier to move the refrigerator without damaging the flooring or the appliance itself.
Causes of a bad Front Roller Assembly can include wear and tear from regular use, damage from moving the refrigerator improperly, or corrosion over time.
Symptoms of a bad Front Roller Assembly include:
This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.
The front wheel assembly replacement (WRXO2X12454) was straightforward and easy to do. Took maybe 30 minutes start to finish. The rear wheel assembly (wheel WRO2X10695 and axle WRO1X10604) that was more involved as the original wheel axle is actually a rivet that you have to cut out. 1. I used a vibrating multitool with a carbide blade to cut the axle out. Had to use a pair of vise grips to hold the rivet to keep it from spinning while cutting it. 2. The new axle I drilled a 2mm hole thru the... Read more
White foam gasket that seals refrigerator shelf edges. Replace if worn, cracked, or missing to prevent spills and maintain proper support. Verify fit with your model number.
Great site to DIY! Purchased fresh produce drawer railing and parts. Fixed in under 10 minutes. Thanks so much! Read more
Ordered the new shelf from Appliance Parts Pros, which was a genuine OEM part and much less expensive than the GE Store. Lifted the old shelf out, popped the new one in and it was done. two minutes. Read more
Replaced Ice maker very easy. Read more
First I ordered a new ice door seal, spring, and crank, figuring the condensation in freezer and door was caused by ice door not sealing. Turns out the solenoid for the ice door was completely rusted and was the primary cause, if it had been replaced early, it would have saved the dispenser board. What then happened was the moisture in the freezer door damaged the control board rendering dispenser controls inoperative as well as the heater around the dispenser. Now the freezer door is dripping... Read more
I ordered the upper and lower cam riser, replaced them, and adjusted the door and the door works great. I've bought many parts in the last 10 years from AppliancePartsPros for this 20-year-old side-by-side refrig. Still works great. Thanks, ED Read more
Swapped it out for new tube. Take 5 minutes and zero effort. The drain tube will clog with mold. You can clean it out but the tube will clog again despite's you best efforts as the tube wall provide a great habitat. Ordered new tubes to facilitate swap-outs. Old tubes can be cleaned but will recolonize quickly. Read more
I ordered the heater unit from your website as well as a new evaporator panel gasket and thermostat. Once I removed the evaporator panel from the rear wall of the freezer side, I used a steamer machine I had to melt all the ice which had accumulated, I replaced the faulty heater unit and all is well. By-the-way, I consider your website amongst the very best and easy to use. I appreciate how well your developers and designers created the diagrams/pictures with numbered parts displayed,... Read more
Fridge not cooling or making clicking sounds? The compressor start relay energizes the start winding to get your compressor running. DIY-friendly repair.
Went to appliance parts Web site looked at the symptoms ordered the suggested parts, my favorite was watching the part repair video, on what the part does and how to install, got the parts the next day, defrosted the fridge 100%, and one by one installed each part what an easy process the video showed exactly where the part was located and how to remove the old and install the new one, now my fridge is working and cooling better than before I saved over $1,400, didn't have to buy a new... Read more
Color: white. It measures about 16.5 inches wide by 4 inches high by 5.5 inches deep.
Replaced shelves Read more
Replaced overload and start relay. went through your troubleshooting guide, found my symptoms, watched repair video. repair video is a big help especially when it is the same model as the one you are trying to repair. easy repair. Read more
Color: white. Measures about 16 inches wide by 2 inches high by 2-1/2 inches deep.
Ordered replacement parts. Had trouble attaching handle with gasket. Had to look at vege draw to figure it out. Read more
I ordered the recommended front door shelf part Fz for my frig, it was shipped promptly. It was slightly too long, so I cut about a 1/4" with the saw... it fits nicely now. Read more
Very easy to replace the trays slide the broken one out, slide the new one in, no problems. Read more
A cap handle is a feature on refrigerators that allows the user to operate the device easily. The cap handle is located on the lower portion of the door handle. It is a largely cosmetic item, but it is also an access point if the door handle has to be removed. It covers the screws that hold the handle in place.A visual inspection will determine the condition of a cap handle. The replacement of this component is a quick and straightforward process. If there is an existing cap handle, remove it entirely first. Clean the area where the new cap handle will be placed. Align the part in the proper position and apply pressure. It will snap into place when done correctly.This cap handle is a genuine OEM replacement part. It is sourced directly from the manufacturer. The cap handle is made of durable materials and sold as an individual unit. This cap handle fits on various models of refrigerators. It is compatible with appliances manufactured by General Electric, Hotpoint, and RCA.
Super easy took less than 5 minutes to install all parts! Every part was correct and fit beautifully. I used a razor blade to cut the ends of the water line before placing the union connector, other than that no tools required. Be sure to fill the water filter before install to minimize the air explosion that I experienced, just blew water all over me as I was running the water to clear the line. Drain at least a gallon and a half before consumption, you will see a color and clarity change. Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.