Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Ice dispenser stuck on crushed or not dispensing? This armature kit connects the solenoid to the chute door. Moderate DIY repair with video guide.
Replaced the water supply valve...boom! Read more
Seals the front edge of your refrigerator's crisper or pantry drawer pan cover to prevent cold air loss. Replace if worn, cracked, or not sealing properly.
First I ordered a new ice door seal, spring, and crank, figuring the condensation in freezer and door was caused by ice door not sealing. Turns out the solenoid for the ice door was completely rusted and was the primary cause, if it had been replaced early, it would have saved the dispenser board. What then happened was the moisture in the freezer door damaged the control board rendering dispenser controls inoperative as well as the heater around the dispenser. Now the freezer door is dripping... Read more
Replacement mounting screw for refrigerator shelves, drawers, and internal components. Needed when screws are lost, stripped, or damaged during repairs.
I ordered new parts from appliance parts pros I had the parts the next day and they were very easy to install Read more
Rubber grommet that mounts the evaporator or condenser fan motor to its bracket. Replace when worn, cracked, or missing to reduce vibration and noise.
Condenser fan stopped on my big 2003 Monogram 4 foot wide ZIS480D Refrigerator. It is top mounted. The fridge had to be rolled out. 20 screws removed and the top sheet metal to get at the condenser. That was the only way to get at it. Works like new now. Read more
Fix a light that won't turn on or flickers in your refrigerator. This E12 socket replacement is straightforward with our step-by-step video guide.
When diagnosing the problem, I discovered that the ice door was not properly sealing and that the solenoid had appeared to rust/corrode forcing the door open. I replaced most of the ice dispenser internals (solenoid, crank, door, and spring) following the video. The door will now open when dispensing ice (which it does!), and will oddly stay open for a few seconds once I am finished, but does seal properly and the chute/container no longer frosts over. Read more
Fix a cracked or broken ice bucket glide that causes your bin to stick or misalign. This right-hand slide rail restores smooth drawer movement in 30 minutes.
It was very simple, took longer to unload freezer than to install glides Read more
Refrigerator not cooling or compressor clicking on and off? This compressor kit restores cooling. Requires certified technician with specialty tools.
Replacement door handle for GE side-by-side refrigerators. Install this handle when your original is cracked, broken, discolored, or worn from years of use.
Replaced with new handles Read more
Clear lens covering the lower refrigerator lamp. Replace if cracked, yellowed, or missing to restore even lighting. Confirm fit with your model number.
Just enter the appliance model and the all the parts are pictured! Really easy! Read more
Plastic water line that runs from the water valve to the icemaker fill tube. Replace if cracked, brittle, broken, or leaking at connection points.
Thanks to the AppliancePartsPro, I ordered it online and received it quickly. I even used the step by step directions on how to replace the tube from the AppliancePartsPro website. Just be very careful and review the instructions first. Couple of important things: 1. Take a picture of the existing wiring and tubes before you take them apart. 2. *if* you remove the wires ( red and white plugs) from the valve, make sure you plug them back in correctly. 3. Do not pull or push the tubes hard. Use... Read more
Secures the ice chute flapper in your refrigerator door. Replace if cracked or missing to restore proper sealing and prevent frost buildup. Verify fit.
I replaced the solenoid, door, spring and bucket. The bucket cracked from ice freezing inside it. Ice froze inside the bucket because the solenoid stopped pulling the door closed which allowed hot humid air into the freezer. While I was in there I replaced the dispenser door, spring and crank because they are cheap and the old ones were moldy. The mold is most likely from the door not closing and causing condensation on the parts as well. Read more
White plastic door bin for refrigerator fresh food section. Replace cracked, broken, or missing door storage bins. Measures 18" wide. Slides onto door.
White foam gasket that seals refrigerator shelf edges. Replace if worn, cracked, or missing to prevent spills and maintain proper support. Verify fit with your model number.
Great site to DIY! Purchased fresh produce drawer railing and parts. Fixed in under 10 minutes. Thanks so much! Read more
Glide bracket that supports the ice bucket in your freezer. Replace if cracked, broken, or missing to restore proper ice bucket installation.
Replaced the support bracket for the ice bucket. Replaced the auger motor for the ice dispenser and installed the new coupler for the microwave tray to spin. Everything works great now! Read more
Internal water reservoir with attached tubing that stores and delivers chilled water to the dispenser. Replace if cracked, leaking, or damaged.
Installing the tank went quickly. Removed the water filter from the upper compartment to stop water flow to the tank. Had to remove the two lower drawers (they tilt out of their sliding frames). There is a glass shelf that should be pulled out - it slides out via two notches in the front frame. The water tank is behind a white metal cover held by 4 screws. Keep track of all of the parts including the lip seals from the shelf. I used two Watts 5/15x5/16 couplers from Lowes for the connections.... Read more
Black plastic funnel extension attaches to the front of your refrigerator's ice dispenser. Replace if cracked, broken, or missing to reduce splashing.
I ordered the ice door assembly and a door recess spring and while I was working on that particular area the ice chute funnel that kept falling off on one side. It was all very easy, took maybe 15 mins in all. I watched the "how to" video that was posted and it was extremely helpful, giving me to confidence to do this myself. The only thing I might do different another time would be to take a look at the assembly before ordering parts. I didn't as I didn't want to keep opening the area up... Read more