Gtup240gm Parts

This water inlet valve assembly regulates the flow of household water into the washer during fill cycles. Replacing it restores consistent fills and helps resolve issues like no water, slow fills, or water leaking into the tub.

• Opens and closes to control water flow into the machine as commanded by the control system
• Helps the washer reach proper fill levels for wash and rinse cycles
• Typical symptoms: no fill, slow fill, fill errors, or water seeping into the tub when the washer is off
• Leaks around the valve or hose connections can also indicate the part has failed

• Unplug the washer and turn off both water supply valves before servicing
• Label hot and cold hoses and take a reference photo before removal
• Expect residual water; use a towel or container. Reconnect electrical connectors and hoses; tighten fittings without overtightening
• After installation, open supply valves and run a test fill while checking for leaks

The Idler Arm Assembly is an OEM component specifically designed for GE dryers. It is a vital part that helps transfer power from the motor to the tumbling action of the dryer drum. The idler arm assembly allows the belt to provide smooth, consistent power to operate the drum efficiently during each cycle.  

Symptoms of a bad idler arm assembly include:

• Squealing or grinding noises coming from the dryer motor or drum area
• The dryer drum not rotating or spinning slowly
• Loose, cracked, or worn idler pulley
• A worn or slipping dryer belt 

Causes of failure can be normal wear and tear over extended use. Excess vibration from an unbalanced load or a dropped object inside the dryer could also potentially damage the idler arm.

This part is compatible with Hotpoint, RCA, and Kenmore dryer models.

This is a small screw, and it is made for dryers, washers, and washer dryer combos. This is a genuine replacement part made by General Electric. Screws are common in these appliances and can cause many difficulties if they become loose, damaged, or missing.A new screw might be needed if there are areas in the appliance that seem off balance or not level. Another way to tell if a new screw is needed is if there are parts in the appliance that are loose or falling off. This is common over many years of normal use as the shaking of washers and dryers can eventually lead to loose screws. Be sure the washer or dryer is completely off before attempting to replace any screws.This is an OEM part sourced directly from the manufacturer. It is sold individually and is compatible with washers, dryers, and washer dryer combos made by General Electric.

This exhaust blower gasket seals the joint between the dryer's blower outlet and exhaust duct. It helps maintain proper airflow and contain lint and heat, supporting efficient drying and preventing leaks into the cabinet or laundry area. What it does:

• Seals the blower-to-exhaust connection to prevent air and lint leaks
• Helps maintain designed airflow through the drum and vent system
• Can reduce warm air or lint escaping inside the cabinet

• 1 gasket

• Disconnect power; for gas dryers, shut off gas and disconnect the supply. Allow the dryer to cool.
• Access the blower housing/exhaust duct; remove panels as needed.
• Remove the old gasket and any residue; clean mating surfaces and lint before installing.
• Seat the new gasket evenly and reassemble; avoid overtightening fasteners and ensure the home vent is clear.

This washer suspension support kit replaces the supports that steady the wash tub. It helps control vibration and balance during wash and spin for smoother operation, reduced noise, and fewer out-of-balance interruptions.

• Supports and centers the tub assembly to reduce vibration during agitation and spin
• Helps prevent banging, walking, and excessive movement
• Aids the washer in reaching proper spin speed without balance-related pauses
• Symptoms of wear include shaking, thumping, or a leaning tub

• Disconnect power and shut off water supply before servicing; wear gloves
• Support the tub before removing old supports and release spring tension carefully
• Install new supports evenly and ensure each end is fully seated in its sockets
• Re-level the washer and run a rinse/spin test to verify smooth operation

The Door Gasket is an OEM part for GE dryers. This seal prevents hot air from escaping during a cycle, ensuring that the dryer operates efficiently and safely. The gasket's primary role is to maintain the internal temperature and airflow, which are essential for the drying process.  

Causes of damage to the door gasket often involve regular wear and tear from opening and closing the dryer door.  

Symptoms of a bad Door Gasket include:

• Clothes taking longer to dry or not drying fully due to heat escaping from the dryer.
• An increase in energy consumption as the dryer works harder to maintain the required temperature.
• Visible wear, tears, or gaps in the gasket 
• Heat leakage from around the dryer door 

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Gasket Door Lower is an OEM part for GE dryers, designed to enhance the efficiency of the appliance by sealing the lower part of the dryer door. This gasket prevents hot air from escaping during operation, ensuring that the dryer functions efficiently and safely.

Causes of damage to the lower door gasket typically include normal wear and tear from regular use.

Symptoms of a bad Gasket Door Lower include:

• Increased drying times, as escaping hot air reduces the dryer's efficiency.
• Higher energy bills due to the dryer working harder to compensate for the loss of heat.
• Visible damage or wear to the gasket, such as cracks, tears, or a loose fit
• A noticeable gap at the lower part of the door

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This washer agitator assembly mounts on the drive shaft and creates the back-and-forth wash action that moves laundry through water and detergent. Replacing a worn or cracked agitator restores proper turnover and cleaning performance.

• Attaches to the drive shaft/transmission to produce the oscillating wash action
• Circulates clothes for even cleaning and reduced tangling
• Replace if the washer won't agitate, the agitator free-spins or slips, laundry stays on top, or it's visibly cracked/loose
• Can also help address squeaking, clicking, or grinding caused by a damaged agitator

• Unplug the washer and turn off water supply; wear cut-resistant gloves
• Remove the dispenser/cap if present, then the inner cap; take out the retaining bolt or nut
• Lift the old agitator straight up; if stuck, rock it gently to free it without damaging the tub
• Align the new agitator with the drive splines, press down fully, reinstall fastener and cap, then run a short cycle to ensure proper agitation

This replacement hinge supports and pivots the appliance door so it opens and closes smoothly and stays aligned. A worn or bent hinge can lead to door sagging, scraping, or poor latching that impacts performance and safety. What it does

• Supports the door and provides the pivot point for opening/closing
• Maintains door alignment to help ensure a proper seal
• Restores smooth, consistent door motion
• Common symptoms: door sags, squeaks, scrapes, or won't latch/stay closed

• 1 hinge

• Disconnect power before servicing; for gas units, also shut off gas supply
• Support the door while removing/installing fasteners to prevent stress on the panel
• Reuse original mounting screws/hardware unless damaged
• After installation, adjust if needed

This control knob assembly lets you select cycles and settings on your dryer. Replacing a cracked or stripped knob restores firm engagement with the timer or selector so you can set, start, and adjust drying reliably.

• Attaches to the control shaft to turn the timer or selector
• Provides a secure grip and pointer to choose cycles and options
• Restores proper control when the original knob is cracked or the hub is stripped
• Typical symptoms: knob spins without turning the shaft, feels loose, falls off, or is missing

• Disconnect power to the dryer before servicing
• Pull the old knob straight off; note the shaft shape and orientation
• Align the new knob with the flat/D-shaft and press until fully seated
• If your model uses a separate dial ring or clip, transfer it from the original

This washer motor run capacitor stores and releases electrical energy to help the drive motor start and run smoothly. Replacing a weak capacitor can help restore consistent agitation and spin and reduce motor humming or stalling under load.

• Provides the phase shift and torque assist the drive motor needs to start and stay running
• Can address: washer won't start, no agitate or spin, motor only hums/buzzes, or stops under load
• Visible clues of failure can include a swollen, cracked, or leaking capacitor case

• Unplug the appliance before servicing; capacitors can retain a charge even when power is off
• Discharge the capacitor safely before handling
• Note wire positions; move leads to the same terminals and secure the capacitor in the original bracket/orientation
• Inspect connectors and replace any burnt or loose terminals to ensure a tight fit

This valve regulates the flow of water into your washer during each cycle. Replacing a failing valve restores proper fill rate and temperature selection to help prevent long fills, no fill, or leaks from a valve that won't close.

• Opens and closes to supply water to the tub when the control calls for fill
• Delivers hot and/or cold water based on the selected temperature setting
• Common symptoms of failure: no fill or very slow fill
• Water dripping into the tub when the washer is off, or leaking around the valve
• Incorrect water temperature during fill

• Disconnect power and turn off both water supplies before servicing
• Place a towel or pan to catch residual water; carefully disconnect hoses
• Note hose and wire positions; transfer connectors to the new valve one at a time
• Restore water and power, then check all connections for leaks and run a quick fill test

This locking clip secures a mating component inside the washer, keeping it firmly attached to its mounting point. Replacing a worn or missing clip restores a snug fit and helps prevent movement, intermittent connections, and noise during operation.

• Retains the designated component securely to its bracket or panel
• Helps prevent vibration-related movement, rattling, or disconnection
• Maintains proper alignment for consistent operation
• Typical signs of failure: cracked or missing clip, part won't stay seated, new looseness around the mount

• Disconnect power and turn off water before servicing
• Access the clip location per your model's service information
• Release and remove the old clip; inspect the mating part for damage or wear
• Seat the new clip fully until it locks; verify the component is secure before reassembly

This electronic water level pressure switch senses air pressure from the wash tub and tells the control when to start and stop filling. Replacing a failed switch restores proper fill levels and helps cycles advance reliably. What it does:

• Monitors tub water level via an air hose connected to the switch
• Signals the control to start/stop the inlet valves at the correct level
• Enables cycle progression by confirming empty/full status
• Common symptoms: won't stop filling, stops filling too soon, incorrect water level, or water-level error codes

• 1 electronic pressure switch

• Disconnect power and turn off water supply before servicing
• Access the switch in the control console or rear cabinet area (location varies by model)
• Move the pressure hose and wire connector(s) over one at a time; ensure airtight hose fit and proper routing without kinks
• Inspect the hose and air dome for cracks, kinks, or blockages; clear or replace if needed

This replacement cover fits the washer's front service door. It restores a clean, finished look and helps shield the service compartment from dust and debris when the original cover is cracked, loose, or missing.

• Covers the service opening to protect internal components from debris and accidental contact
• Restores cabinet appearance by concealing the service area
• Replaces a broken, warped, loose, or missing cover
• Common symptoms: cover won't stay closed, visible cracks, rattling, or a missing access cover

• Disconnect power and turn off water before servicing
• Remove the damaged cover
• Align the new cover with the existing hinge/tabs and secure per your model's configuration
• Confirm proper closure and clearance before restoring power