Your privacy choices: We and our partners use cookies for analytics and ads. Decline all turns them off.
Privacy Policy · Do Not Sell or Share My Personal Information
Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Dishwasher leaking from bottom or making grinding noise? The sump housing often cracks or wears out. Moderately difficult repair, about 45 minutes.
I noticed the floor around the dishwasher was starting to get wet and warp the wooden floor. The chopper had gotten out of line and had cut a pinhole into the sump housing and the dishwasher was leaking badly. It was quite easy to repair. Just unhook the drain hose and the wire connectors, twist off the turbidity sensor and waste motor, pull out the shims and the whole assemple comes up and out. The hardest part was pulling the motor off of the assembly, since I wasn't sure if I needed to... Read more
Fix dishwasher overflows and leaks with a new float assembly. Controls water level to prevent overfilling. Moderate DIY repair with video guide.
Removed bottom cover, located leak at float switch, removed and replaced float switch kit. The toughest part of the repair was removing the Float & Retainer Assembly (in the interior of the machine tank) which broke when I pushed it back and pulled it straight up as suggested in the service manual. The Float Switch Kit (attached to, and below the float, below and outside the tank) has a folding plastic cover which fastens with plastic clips. If you open the switch kit before removing the... Read more
Secures water inlet tubing to create a leak-resistant seal. Replace if cracked, stripped, or leaking at the connection. Verify fit with your model.
Dishwasher washer would not drain after hearing glass-like particles during the drain cycle despite trying to clean the cylinder filter. Originally suspected the drain motor was damaged. After watching a video on how to replace the drain pump, I carefully energized the dishwasher (from water and electricity) then removed the dishwasher to take a look. After removal of drain hose from the pump, discovered that drain hose was connected to water inlet assembly which also needed removal to... Read more
This factory-specified screw secures panels, brackets, and internal components in your appliance. Replacing worn or missing hardware restores a tight fit to help reduce vibration, noise, and premature wear.
My son fixed the issue of some wear and tear. Read more
If your dishwasher door drops, slams, or feels heavy, the door balance mount may be broken. This side-frame bracket anchors the spring system.
Replaced pump and motor. Read more
Standing water or dirty dishes? A clogged or damaged pump inlet screen blocks debris from the wash system. Simple DIY fix restores drainage and cleaning.
Looked at Dishwasher. Scratched head and armpit. Told wife I would fix, not repariman. Wife skeptical - shook head. Found schematic on web. Found YouTube video of guy repairing same DW model. Disassembled. Diagnosed problem. Chopper assembly welded in place by water scale -broke removing. Potty mouth. Ordered parts. Waited for parts. Washed dishes by hand. Wife doing ok. Parts arrived (in only a day or two!!! Fed Ex for 7 bucks!! Great deal). Put on nasty t-shirt, baggy shorts. ... Read more
Secures the dishwasher's water inlet tube in position, preventing movement and strain on fittings. Replace if cracked, broken, or missing to restore support.
We bought replacement parts from you and my daughter fixed it. It is working now. It would have been nice if all the parts came in a set. Read more
Gray plastic pivot clip for dishwasher upper rack tine rows. Replaces broken, cracked, or missing pivots that prevent tines from adjusting properly.
With the basket out of the dishwasher, the plastic parts basically snap on and off... popped the broken parts off and the new parts on. The 2 wheel and mount assemblies were a little more complicated. The video on the website advises to disconnect the supply line and drain line... I didn't have to do this. I just pulled the dishwasher out of its cabinet a little over a foot and removed the 2 screws holding each assembly in place and removed them. The previous gaskets (2 PER ASSEMBLY)... Read more
Dishwasher not heating or drying properly? This heater probe shield protects temperature sensors and nearby components from heat damage for accurate sensing.
A bit of searching on the internet narrowed the problem down to either the heating element or the control board. As I am not much of a diagnostician I decided to replace both. Along this same line, I would never have attempted these repairs if it hadn't been for the clear, easy to understand repair videos provided for each part. Further, my decision to do my own repairs was made easier because the prices of the parts was so reasonable. I took my time, reviewed the videos and replaced the... Read more
Bottle with brush. Color: Black. Size: 0.6 fl.oz.
Replaced It With New One Read more
This bracket mounts inside the dishwasher tub and supports the middle spray arm manifold tube, holding it securely in position. It ensures the spray arm tube stays aligned so water is properly distributed during the wash cycle. Replace this bracket if the middle spray arm wobbles, falls out of place, or if dishes on the upper rack are not getting clean due to poor water coverage.
Installed new part Read more
Replaces damaged dishwasher dishrack wheel assembly. Installs on upper or lower rack for smooth rolling. Needed when wheels crack or tabs break.
Part needed replacement Read more
12 Ft in length
Read directions on how to change the power cord and watched video on your site on how to change the drain hose. Everything went perfectly. Read more
Fix a dishwasher that won't start or stops mid-cycle due to door latch failure. This handle assembly ensures proper door closure and cycle operation.
Adjustable manifold that connects the upper rack to the rear water feed tube. Replace if cracked, punctured, corroded, or missing the seal probe.
Replace the entire assembly, manifold, spray arm with seal and water probe. Took 5 minutes. Problem solved! Read more
Size: 1/4 inch hex head, 10-12 x 1/2 inch.
This trash compactor is in our vacation home. We never use it and now we are selling the house. When I looked to replace it I was amazed at how expensive a new compactor would cost. I found the serial number on the current compact entered it and your web site came up. Your schematics were excellent and made the repair very easy! Read more
Opt-Out Request Honored
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.