Gud27gssjoww Parts

This exhaust blower gasket seals the joint between the dryer's blower outlet and exhaust duct. It helps maintain proper airflow and contain lint and heat, supporting efficient drying and preventing leaks into the cabinet or laundry area. What it does:

• Seals the blower-to-exhaust connection to prevent air and lint leaks
• Helps maintain designed airflow through the drum and vent system
• Can reduce warm air or lint escaping inside the cabinet

• 1 gasket

• Disconnect power; for gas dryers, shut off gas and disconnect the supply. Allow the dryer to cool.
• Access the blower housing/exhaust duct; remove panels as needed.
• Remove the old gasket and any residue; clean mating surfaces and lint before installing.
• Seat the new gasket evenly and reassemble; avoid overtightening fasteners and ensure the home vent is clear.

This trap duct and felt kit restores the dryer's front airflow path and drum seal. Replacing a damaged duct or worn felt helps maintain proper airflow, improve drying performance, and reduce lint leaks and noise. What it does:

• Routes exhaust air through the lint filter housing to the blower
• Seals the drum front to prevent air leaks and reduce fabric snagging
• Helps address long dry times, lint escaping into the cabinet, and scraping/squealing from a worn front seal
• Replaces cracked, warped, or melted lint trap duct components

• One trap duct and one felt seal

• Disconnect power; shut off gas supply for gas dryers before servicing
• Remove top/front panels to access the lint filter housing and front bulkhead; support the drum as needed
• Clean mating surfaces; install the felt with the soft pile facing the drum to form a continuous, even seal
• Reuse original fasteners/hardware; the lint filter seats fully and the drum turns freely before testing

This washer agitator assembly mounts on the drive shaft and creates the back-and-forth wash action that moves laundry through water and detergent. Replacing a worn or cracked agitator restores proper turnover and cleaning performance.

• Attaches to the drive shaft/transmission to produce the oscillating wash action
• Circulates clothes for even cleaning and reduced tangling
• Replace if the washer won't agitate, the agitator free-spins or slips, laundry stays on top, or it's visibly cracked/loose
• Can also help address squeaking, clicking, or grinding caused by a damaged agitator

• Unplug the washer and turn off water supply; wear cut-resistant gloves
• Remove the dispenser/cap if present, then the inner cap; take out the retaining bolt or nut
• Lift the old agitator straight up; if stuck, rock it gently to free it without damaging the tub
• Align the new agitator with the drive splines, press down fully, reinstall fastener and cap, then run a short cycle to ensure proper agitation

This dryer gasket seals critical air paths in your GE dryer to maintain proper airflow, temperature, and efficiency. Replacing a worn seal helps prevent heat loss and lint escape while reducing noise and friction.

• Creates an air-tight seal in the dryer to keep heat and airflow where they belong
• Helps contain lint and moisture within the drum and exhaust path
• Supports efficient drying performance and consistent temperatures
• Common failure signs: longer dry times, warm air leaking near the opening, visible tears or fraying, excess lint around the door/front panel

• Disconnect power; turn off gas supply before servicing
• Allow the dryer to cool completely; wear cut-resistant gloves
• Access the gasket location per your model's service instructions
• Remove the old gasket and residue, clean the surface, position the new gasket correctly, and reassemble; allow any adhesive to set if your model requires it

This is the drive motor and pulley assembly for GE dryers. It turns the drum via the belt and powers the blower wheel, restoring proper tumbling and airflow when the original motor is weak, noisy, or not starting.

• Powers the drive belt to rotate the dryer drum
• Turns the blower wheel to move air through the drum and exhaust
• Typical symptoms of a failing motor: dryer won't start, drum won't turn, loud humming/buzzing, or stops mid-cycle from overheating
• Restores consistent tumbling and drying performance

• Disconnect power; for gas models, also shut off the gas supply
• Access the motor by removing panels and relieving belt tension; remove drum as needed
• Label/photograph wiring and transfer the blower wheel and any brackets or clamps from the old motor
• Spin the drum by hand before restoring power

This replacement hinge supports and pivots the appliance door so it opens and closes smoothly and stays aligned. A worn or bent hinge can lead to door sagging, scraping, or poor latching that impacts performance and safety. What it does

• Supports the door and provides the pivot point for opening/closing
• Maintains door alignment to help ensure a proper seal
• Restores smooth, consistent door motion
• Common symptoms: door sags, squeaks, scrapes, or won't latch/stay closed

• 1 hinge

• Disconnect power before servicing; for gas units, also shut off gas supply
• Support the door while removing/installing fasteners to prevent stress on the panel
• Reuse original mounting screws/hardware unless damaged
• After installation, adjust if needed

The Tub Cover Assembly is an OEM part for GE top-load washing machines. It covers and protects the agitator and inner tub inside the washer.

Causes of a bad tub cover can include damage such as cracks or ruptures over time from repeated use, or warping due to exposure to high heat or moisture. 

Symptoms of a defective tub cover assembly include:

• Water leaks inside or outside the washer during operation  
• Increased noise levels from an unsecured or poorly fitted cover
• Inability to fully close or lock the washer door or lid

This genuine GE replacement is also compatible with Hotpoint, RCA, and select Kenmore units. 

This washer motor run capacitor stores and releases electrical energy to help the drive motor start and run smoothly. Replacing a weak capacitor can help restore consistent agitation and spin and reduce motor humming or stalling under load.

• Provides the phase shift and torque assist the drive motor needs to start and stay running
• Can address: washer won't start, no agitate or spin, motor only hums/buzzes, or stops under load
• Visible clues of failure can include a swollen, cracked, or leaking capacitor case

• Unplug the appliance before servicing; capacitors can retain a charge even when power is off
• Discharge the capacitor safely before handling
• Note wire positions; move leads to the same terminals and secure the capacitor in the original bracket/orientation
• Inspect connectors and replace any burnt or loose terminals to ensure a tight fit

Door gasket seals the door assembly to limit air leaks and keep heat and moisture inside the drum. Replacing a worn gasket restores airflow, improves drying performance, and reduces lint and warm air escaping at the door.

• Forms a compression seal around the dryer door opening/window to prevent air leaks
• Helps maintain proper drum temperature and airflow for efficient drying
• Replace if the gasket is torn, flattened, brittle, loose, or missing
• Helps with: warm air or lint escaping at the door, longer dry times, door rattle, visible wear on the gasket

• Disconnect power; for gas models, also shut off the gas supply and allow the dryer to cool
• Remove the door and separate inner/outer door panels as needed; note gasket routing/orientation
• Clean mating surfaces; install the new gasket without stretching and seat it evenly around the perimeter
• Reassemble and verify an even seal around the door; run a short test cycle to check for leaks

The Rotatory Knob is an OEM part for GE washers. It allows users to easily select and change washer settings like cycles, temperatures, and options with a simple turn. As a control interface component, the rotatory knob provides direct input to the washer's control board.

Causes of a bad rotatory knob can be normal wear from frequent use over time. Exposure to moisture, physical impacts or mishandling, and mineral buildup are other potential causes of malfunction. 

Symptoms of a bad rotatory knob include:

• Difficulty selecting or changing washer settings  
• Loose, wobbly, or unresponsive knob behavior
• Inaccurate input to the control board causes operating issues
• Cracks, splits, or broken knob components

Compatible with some Hotpoint, RCA, and Kenmore models as well.

This locking clip secures a mating component inside the washer, keeping it firmly attached to its mounting point. Replacing a worn or missing clip restores a snug fit and helps prevent movement, intermittent connections, and noise during operation.

• Retains the designated component securely to its bracket or panel
• Helps prevent vibration-related movement, rattling, or disconnection
• Maintains proper alignment for consistent operation
• Typical signs of failure: cracked or missing clip, part won't stay seated, new looseness around the mount

• Disconnect power and turn off water before servicing
• Access the clip location per your model's service information
• Release and remove the old clip; inspect the mating part for damage or wear
• Seat the new clip fully until it locks; verify the component is secure before reassembly

This electronic water level pressure switch senses air pressure from the wash tub and tells the control when to start and stop filling. Replacing a failed switch restores proper fill levels and helps cycles advance reliably. What it does:

• Monitors tub water level via an air hose connected to the switch
• Signals the control to start/stop the inlet valves at the correct level
• Enables cycle progression by confirming empty/full status
• Common symptoms: won't stop filling, stops filling too soon, incorrect water level, or water-level error codes

• 1 electronic pressure switch

• Disconnect power and turn off water supply before servicing
• Access the switch in the control console or rear cabinet area (location varies by model)
• Move the pressure hose and wire connector(s) over one at a time; ensure airtight hose fit and proper routing without kinks
• Inspect the hose and air dome for cracks, kinks, or blockages; clear or replace if needed

This replacement cover fits the washer's front service door. It restores a clean, finished look and helps shield the service compartment from dust and debris when the original cover is cracked, loose, or missing.

• Covers the service opening to protect internal components from debris and accidental contact
• Restores cabinet appearance by concealing the service area
• Replaces a broken, warped, loose, or missing cover
• Common symptoms: cover won't stay closed, visible cracks, rattling, or a missing access cover

• Disconnect power and turn off water before servicing
• Remove the damaged cover
• Align the new cover with the existing hinge/tabs and secure per your model's configuration
• Confirm proper closure and clearance before restoring power

The Drive Motor and Control Board Kit is an OEM part for GE washers. It includes both the drive motor, which powers the movement of the wash basket or tub during cycles, as well as the control board which communicates with and regulates the functions of the motor. This integrated kit works seamlessly to provide the necessary wash and spin motions.

Symptoms of a bad drive motor and control board kit include: 

• The washer tub not turning or agitating during wash cycles
• Inability to advance cycles  
• Electrical issues such as sparking or burning smells
• Fault codes displayed or cycles stopping prematurely

Causes can be normal wear and tear over time, water damage corrupting electronic components, or damage from foreign objects getting lodged in the motor or drive mechanism.

This OEM GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

This spring cover protects and retains a mechanism spring inside your washer. Replacing a cracked or missing cover helps keep the spring seated, limits debris intrusion, and supports smooth, reliable movement of the associated control, latch, or linkage.

• Shields the spring and helps keep it properly seated in its pocket
• Reduces friction and wear that can lead to premature spring failure
• Supports consistent return action for the related control, latch, or lever
• Typical symptoms include a missing/broken cover, exposed spring, rattling, or erratic operation

• Unplug the appliance and turn off water before servicing
• Access point varies by model; photograph spring/cover orientation before removal
• Control the spring during disassembly to prevent sudden release
• Ensure the cover is fully seated; test operation before final reassembly