Hav2588aww Parts

Size: 5 foot long. Rubber fill hose used on most automatic washing machines. Two hoses used per machine.

Specs: 10-16 x 1/2 inch.

This factory replacement screw fastens the specified components in your appliance as shown in the parts diagram. It restores a secure fit and helps eliminate looseness, vibration, and noise when an original fastener is missing, stripped, or corroded.

• Secures panels, brackets, and assemblies at the locations designated for your model
• Direct replacement for the original fastener to maintain proper fit and alignment
• Replace when threads are damaged, head is rounded, or rust is present
• Common symptoms: loose or rattling parts, gaps/misalignment, increased vibration

• Disconnect power and shut off water supply if applicable before servicing
• Refer to your model's parts diagram for exact location and quantity
• Start threads by hand to avoid cross-threading; use the correct driver bit
• Snug firmly but do not overtighten to prevent stripping

This flume hose kit replaces the flexible hose that routes water from the dispenser/fill flume into the washer tub. Restoring a tight, unobstructed hose helps prevent leaks and ensures detergents, bleach, and softener are carried into the wash.

• Directs fill/dispenser water from the flume to the tub during wash and rinse
• Restores proper flow so dispenser compartments empty correctly
• Helps prevent leaks caused by splits, brittleness, or loose connections
• Typical symptoms: water on the floor, dispenser not draining, weak flow into tub, musty odor near dispenser

• Disconnect power and shut off water supply before servicing
• Access the dispenser/flume area by removing the top or control panel per your model
• Note hose routing; transfer and secure clamps; avoid kinks and rub points
• Run a quick fill/rinse to check for leaks at both connections after installation

Replace a worn rear self-leveling leg to restore a stable, level appliance. This foot supports the back of the cabinet and automatically compensates for floor unevenness to help reduce vibration, rocking, and noise during operation.

• Supports and self-levels the rear of the cabinet to maintain stability on uneven floors
• Helps address wobbling/rocking, excessive vibration, rattling or "walking," and an appliance that won't sit level
• Replaces a rear leg that is missing, cracked, or worn
• Promotes smoother operation by helping the unit sit properly level

• Disconnect power; if applicable, turn off the water supply
• With assistance, carefully tilt the appliance to access the rear base
• Remove the damaged rear leg from its mount and install the new leg, ensuring it seats fully
• Lower the unit, verify level with a bubble level, and adjust front legs as needed for final leveling

This lid switch actuator engages the washer's safety switch when the lid is closed so cycles can start and spin as designed. Replace a broken or missing actuator to restore proper lid switch engagement and reliable operation.

• Engages the lid switch when the lid is closed to enable agitation and spin
• A worn, cracked, or missing actuator can cause the washer not to start or to stop before spin
• Intermittent operation that changes when pressing on the lid often indicates misalignment
• Lack of an audible "click" from the lid switch can point to a faulty actuator or alignment

• Disconnect power before servicing; do not work on a live appliance
• Access the lid/switch area per your model's service procedure
• Remove the damaged actuator and install the new part, securing as designed
• Before reassembly, close the lid to ensure the switch clicks and engages properly

One piece. Works on most Maytag washers. Color: white. It measures about 5 inches in diameter, and 5-1/2 inches high.

This suspension spring hook connects a tub suspension spring to the washer frame, helping support and center the wash basket. Replacing a worn or missing hook can reduce shaking, banging, and off-balance interruptions during spin.

• Secures one end of a suspension spring to the cabinet/base
• Helps control tub movement and absorb vibration during agitation and spin
• Failure signs include excessive vibration or banging, tub leaning/sagging, or frequent out-of-balance stops

• Disconnect power and water; wear gloves and eye protection
• Access the suspension area per model; support the tub to relieve spring tension
• Use pliers or a spring tool to remove the old hook; note orientation and mounting location
• Seat the new hook fully and ensure the spring is engaged securely before reassembly and testing

This washer drain hose routes wastewater from the drain pump to your standpipe or laundry tub. Replacing a cracked or kinked hose restores reliable draining and helps prevent leaks during the spin/drain cycle.

• Connects the washer's drain outlet to the household standpipe or laundry tub
• Molded bend helps position the hose correctly and reduces kinking
• Typical symptoms: water leaking at the back or onto the floor while draining
• Visible splits, soft spots, brittleness, or abrasion on the hose
• Slow or incomplete draining caused by kinks or internal blockage

• Disconnect power and move the washer to access the rear; shutting off water is recommended as a precaution
• Place towels or a shallow pan to catch residual water when removing the old hose
• Transfer and reuse existing clamps/brackets if required; fully seat and secure connections, and route the hose to avoid kinks or rubbing
• Insert the outlet end properly into the standpipe or tub per your model's instructions, then run a quick drain/spin to check for leaks

This replacement timer knob restores manual timer control on compatible Whirlpool appliances, giving a secure grip and smooth turning for accurate time or cycle selection. Easy-to-replace part for worn, broken, or stripped knobs. What it does:

• Replaces a cracked, worn, or missing timer knob so you can set and adjust time or cycle settings.
• Fits onto the appliance timer shaft to provide a secure, easy-to-turn control surface.
• Helps when the knob spins freely, won't engage the timer, or is difficult to turn.
• Restores tactile feedback for precise timer/cycle selection.

• Disconnect power to the appliance before beginning any service.
• Most installations require no tools; pull old knob straight off the shaft and push the new knob on until it seats.
• Align splines on the knob with the timer shaft—do not force; forcing can damage the timer shaft.

This pressure switch hose carries air from the washer tub to the pressure switch so the machine can sense and control water level. Replacing a damaged hose restores proper fill control and prevents level-sensing errors. What it does:

• Channels air/vacuum from the tub to the pressure switch so the control can detect water level.
• A cracked, pinched, or collapsed hose may cause overfilling, underfilling, failure to advance cycles, or continuous fill.
• Restores accurate water-level sensing when replacing a worn or damaged hose.

• Disconnect power to the appliance before servicing to avoid shock or injury.
• Remove and replace the hose carefully; avoid kinks, sharp bends, or pinched routing that can impair sensing.
• Use the factory-style connection points and clamps; ensure both ends are seated securely.
• After installation, run a test fill or diagnostic cycle to confirm correct water-level operation and no leaks.

This retaining ring secures a component on a shaft or within a groove so it stays aligned during operation. Replacing a bent, rusted, or missing ring helps stop wobble, noise, and parts working loose.

• Locks into a groove to keep gears, pulleys, wheels, or spacers from sliding off a shaft
• Helps maintain proper spacing and alignment of moving parts
• Common signs of failure: wobbling parts, scraping/rubbing noises, or components that work loose
• Visual clues: deformation, corrosion, or loss of spring tension

• Disconnect power and any utilities to the appliance before service
• Wear eye protection—retaining rings can spring free under tension
• Note the order/orientation of any washers or spacers before removal
• Use appropriate snap-ring or needle-nose pliers and ensure the ring seats fully in its groove

This washer tub mounting bolt secures the tub assembly to its support points. Replacing worn or missing hardware helps keep the tub aligned and stable through wash and spin, reducing vibration and noise. What it does:

• Anchors the tub assembly to its mounting bracket or frame
• Helps maintain alignment under load and during high-speed spin
• Replace if the bolt is stripped, rounded, rusted, or missing
• Symptoms can include excessive vibration/banging, tub shifting or scraping, and rattling hardware

• 1 mounting bolt

• Disconnect power and water before servicing; wear appropriate PPE
• Support the tub to relieve stress on the mounting points before removal
• Start threads by hand to avoid cross-threading; tighten bolts evenly across all mount points
• Do not overtighten; follow for torque guidance

Drive motor isolator.

Size: 10-32

Motor plate isolator.