Hda3400g02 Parts

This vent pad cushions and seals the dishwasher's door vent, helping route steam out of the tub while protecting the inner door and control area from moisture. Replacing a worn pad can help stop vent leaks and rattling.

• Creates a seal between the vent assembly and inner door liner to contain moisture
• Helps channel humid air during drying and reduces steam escaping at the vent opening
• Cushions the vent assembly to minimize vibration and noise
• Typical symptoms of a failed pad: steam or water at the top of the door near the vent, moisture inside the console, or a rattling vent

• Disconnect power at the breaker and shut off water before servicing
• Open the door and remove inner-door screws to access the vent assembly
• Note pad placement; install the new pad in the same location with clean, dry mating surfaces
• Reassemble and run a short cycle to check the vent area for leaks

Includes screws.

This leveling screw adjusts your dishwasher's leveling leg so you can set the cabinet height and get the unit perfectly level. Proper leveling helps the door seal correctly, reduces rocking, and cuts excess vibration and noise.

• Threads into the leveling leg to raise or lower the dishwasher for accurate leveling and stability
• Helps prevent rocking or wobbling and supports proper door alignment and sealing
• Can reduce vibration/noise associated with an out-of-level installation
• Replaces a stripped, bent, or missing adjustment screw to restore adjustability

• Disconnect power and turn off the water supply; protect flooring before adjusting or replacing
• Remove the toe-kick/access panel to reach the adjuster; support the dishwasher's weight before turning the screw
• Start threads by hand to avoid cross-threading; do not overtighten
• After adjustment, verify level side-to-side and front-to-back with a level and recheck door operation

This lower front toe kick panel restores a clean, finished look at the base of the dishwasher and helps shield the bottom area from debris and bumps. Replace a cracked, dented, or missing panel to secure the opening.

• Covers and conceals the lower access opening at floor level
• Helps protect base components from accidental contact and household debris
• Restores appearance when the original panel is damaged or missing
• Common symptoms: visible gap at the bottom front, loose or rattling kickplate, bent or broken panel

• Disconnect electrical power before servicing
• Open the door to access and remove the mounting screws holding the old panel
• Position the new panel, align tabs/slots, and reinstall screws—do not overtighten
• The panel clears the floor and does not interfere with door operation

This sump cover sits over the dishwasher's pump inlet, acting as a protective guard. It helps keep debris out of the pump, maintains proper water circulation, and protects internal components for consistent cleaning performance. What it does:

• Covers the pump/sump intake to screen larger food particles
• Helps prevent debris from entering the wash pump
• Aids proper water flow to support spray pressure and cleaning
• Common symptoms of a failed cover include poor cleaning, unusual pump noise, and visible damage or warping

• 1 sump cover

• Disconnect power and water supply before servicing; allow the unit to cool
• Remove the lower rack and spray arm or access parts as needed to reach the sump
• Release retaining screws or tabs; note the cover's orientation for reassembly
• Seat the new cover fully and secure it; hand-spin the spray arm and run a short test cycle to check operation

Color: White

This hose clamp kit secures the washer's hoses at the pump, tub, or valve connections, helping stop leaks and hose blow-offs. Replace worn or missing clamps to restore a tight, reliable seal during fill, wash, and drain.

• Secures drain, pump, and fill hoses to fittings to maintain a watertight seal
• Helps prevent drips, leaks, and hoses slipping off during vibration
• Replaces clamps that are rusted, stripped, deformed, or missing
• Common symptoms: water leaking at hose joints, loose hose connections, clamp won't tighten
• Useful when installing a new hose, pump, or valve

• Unplug the washer and turn off water supplies; have towels or a pan ready for residual water
• Release and remove old clamps; seat the hose fully over the fitting before installing new clamps
• Tighten evenly and do not overtighten to avoid hose or fitting damage
• Restore power and water, then run a short cycle to check for leaks at each connection

This lower front kickplate for dishwashers covers the base opening to protect internal components and complete the appliance's appearance. The almond-finish toe kick helps reduce noise escape and restores a clean look when the original panel is damaged or missing. What it does:

• Covers and protects the lower access area, hiding leveling legs and insulation
• Helps contain sound from the base area
• Restores a clean, finished front appearance
• Replace if the kickplate is cracked, bent, rattling, discolored, or missing

• 1 toe kick panel (almond)

• Disconnect power at the breaker before starting; edges may be sharp
• Open the door to access and remove the mounting screws securing the old panel
• Reuse original screws/insulation; align the new panel and set height using the mounting slots
• Tighten screws evenly and verify the door opens/closes without rubbing the panel

This dishwasher timer controls the timing and sequence of wash, rinse, drain, and dry operations. Replacing a failed timer ensures the machine advances through each stage properly for complete cycles and reliable cleaning results.

• Advances the cycle and routes power to pumps, valves, and heater at the correct times
• Can cause cycles to run unusually long/short or skip steps when failing
• Intermittent start/stop behavior during a cycle can also indicate a worn timer

• Disconnect power at the breaker before servicing
• Access the control console; document wire locations and transfer one lead at a time to the new timer
• Mount securely and route wires clear of sharp edges or moving parts
• Restore power and run a short test cycle to proper advancement

This finished access panel mounts at the lower front of the dishwasher to cover the service opening. It restores a clean, factory appearance while helping shield internal components from debris and incidental contact. What it does:

• Covers the lower front service opening at the base of the dishwasher
• Helps protect wiring, pump area, and insulation from debris and accidental contact
• Contributes to overall noise containment and proper ventilation as designed
• Replaces a panel that is dented, bent, rusted, rattling, or missing

• 1 finished access panel

• Disconnect power (and water, if necessary) before servicing the appliance.
• Remove mounting screws securing the existing panel and set the old panel aside.
• Position the new panel and secure it with the original hardware; ensure it sits flush and doesn't interfere with door operation.
• Restore power and check for proper fit and vibration-free operation.

This dishwasher float rises with the water level to engage the float switch. It regulates filling and helps prevent overflows, protecting your kitchen from leaks and keeping wash cycles running properly. What it does:

• Rises with the tub's water level and actuates the float switch
• Signals the inlet valve to stop water flow at the correct level
• A stuck, worn, or broken float may cause overfilling or no-fill conditions
• Symptoms can include leaking from overfill or no water entering during fill

• 1 float

• Disconnect power and turn off the water supply before servicing
• Open the door; remove the lower rack for access
• Lift off any float cap/retainer, pull the old float straight up, and seat the new float
• Ensure the float moves freely; restore power/water and run a brief fill test

This sump clamp secures the dishwasher sump to the tub assembly, keeping the gasket compressed for a watertight seal. Replacing a weakened or corroded clamp helps stop leaks from the base and restores proper wash system sealing.

• Holds the sump firmly to maintain seal compression
• Helps prevent water leaking from the bottom of the dishwasher during operation
• Replace when the existing clamp is rusted, broken, stripped, or won't tighten

• Disconnect power at the breaker and shut off the water supply
• Remove the toe kick and, if needed, pull the dishwasher forward for access
• Position the clamp over the sump-to-tub joint and tighten evenly; do not overtighten
• Reseat the sump gasket and run a leak test after reassembly

This float switch detects rising water in the refrigerator drain pan or lower cabinet area and signals the appliance control to help prevent overflow and water damage. Use it to replace a failed or intermittent water-level sensor. What it does:

• Senses high water level in the drain pan or collection area and closes the circuit to alert the control.
• Helps identify causes of leaks and pooling under or behind the appliance.
• Commonly used when symptoms include water on the floor, drip pan overflow, or water-related error/alert conditions.
• Matches OEM function for refrigeration units that include a float-based water-detection circuit.

• Disconnect power to the appliance before starting any repairs; shut off the water supply if working near water lines.
• Access may require removing lower kick plate or back panel; handle plastic clips and fasteners carefully.
• Disconnect electrical connector gently and note orientation before installing the replacement; secure wiring and verify float moves freely.
• Restore power and run a short test cycle or simulate water level to ensure proper operation.

This lever connects to the dishwasher detergent dispenser mechanism and actuates the cup lid. A worn or damaged lever can prevent the dispenser from opening at the right time, reducing wash performance.

• Transfers motion from the timer/actuator to release the detergent cup lid
• Common symptoms: detergent remains in cup, soap door won't open, poor cleaning results
• Restores reliable dispenser operation during the wash cycle

• Disconnect power and turn off water before servicing
• Access typically requires removing the inner door panel to reach the dispenser linkage
• Note linkage orientation before removal; transfer any springs or clips
• Test dispenser door movement by hand before reassembling

This spring kit restores proper door tension so the appliance door opens and closes smoothly and stays in position. Use it to replace worn or broken springs that cause a sagging, loose, or hard-to-operate door. What it does:

• Replaces worn or damaged door tension springs to restore smooth opening and closing.
• Helps prevent the door from dropping, sagging, or not staying open.
• Reduces uneven or jerky door movement caused by lost spring tension.
• Matches OEM-design function for safe, reliable door operation when installed correctly.

• Disconnect power (and water, if applicable) before beginning any repair.
• Springs are under tension—use caution and proper tools to avoid injury.
• Follow the appliance's service manual or OEM instructions.

Inner door panel replaces the interior face of the appliance door, restoring a clean surface and proper support for door components so the door can close and seal as intended. Ideal when the door liner is cracked, dented, or visibly worn. What it does:

• Serves as the interior surface of the door and supports the inner glass or window.
• Provides a mounting surface for latches, seals, and related hardware to help maintain a proper door closure.
• Reduces rattling, visible damage, or interior door gaps that can affect operation.
• Protects internal door components from debris and normal wear.

• Disconnect power and unplug the appliance before starting any repair.
• Use basic hand tools to remove door trim or screws; keep all fasteners for reassembly.
• Handle inner glass and sharp edges carefully—wear gloves and eye protection.
• Refer to the appliance's service manual or OEM instructions for model-specific removal and reinstallation steps.