Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Adjustable leveling leg screws into washer base to stabilize and level your machine on uneven floors. Replace worn, missing, or damaged legs for stability.
I replaced the drive block & leveling feet, it helped a lot but the washer still shakes a lot, I am now going to try replacing the suspension rod kit, These were the most recommended fixes to the problem.The repairs were not too hard, I wish I had a spanner wrench, I couldn't find it on the website. Read more
This is the fabric softener dispenser cup that fits inside the agitator or dispenser housing of a top-load washing machine. It holds liquid fabric softener and releases it into the wash water at the appropriate time during the rinse cycle. Replace this cup if it is cracked, warped, or clogged, or if fabric softener is not dispensing properly during the wash cycle.
Put the new one on. Read more
Washer won't start or complete cycles? The electronic control board coordinates timing and modes. Moderate DIY repair—remove back panel and swap boards.
The repair was quite simple. The back panel had to be removed which was (5) sheet metal screws and the enclosure lifted. Once that was done all that remained was to remove the wiring from the control board, lift off. Installation was just as easy and as qick. Read more
The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear bulkhead to the tub, ensuring vibrations are reduced through solid mounting points. Properly installed screws dampen oscillating movement.
Causes of a bad screw include damage from water exposure like corrosion or breakage from stress concentrations if the tub bangs around during imbalanced loads.
Symptoms of a bad screw include:
This Whirlpool replacement screw restores a stable suspension system. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Watched several repair videos on YouTube produced by AppliancePartsPros.com for this model Whirlpool washer (videos quite well done). Purchased parts from AppliancePartsPros.com; order correctly filled and parts arrived by FedEx within two working days. Performed repairs as instructed. "Plastic welded" holes in poly outer tub using similar plastic (PP) using a cheap soldering iron - worked perfectly, saved >$150 for new tub. Washer now like brand new. Suggestion - buy the spanner wrench,... Read more
Fix excessive vibration, banging, or walking during spin cycles. This washer damper assembly controls tub movement for smooth, quiet operation.
Two 5-foot nylon braided hoses connect household water supply to washer inlet valves. Replace cracked, leaking, or aging hoses to prevent water damage.
Watched u tube video. Ordered replacement water inlet valve and new hoses. Dismantled washer and replaced defective valve and installed new hoses. The repair went very easily and the washer worked perfectly as a result. Read more
Rubber washer gasket for washer fill hose connections. Replace if worn or leaking at coupler adapter. Measures 1-1/16 x 5/8 inch. Verify fit with model.
Replaced with new part ordered from store Read more
Size: 10-16 x 5/8 inch.
I used a screwdriver and removed all three screws and replaced them with ones I ordered from you. The job took less than ten minutes to complete. Read more
Contains two, six foot long braided hoses with 90 degree ends.
I had a problem with the drain pump on my Kenmore HE3 and I replaced it using a drain pump I ordered from APP. That fixed that problem but once I started running the washer I started getting a FH error code. I looked it up and found that it was a problem with the washer not filling properly. I pulled the washer out and found that one of the fill hoses had kinked when I pushed the washer back in place. There was also some writing on the hose that read "Change hose every five years". I know I had... Read more
Fix a washer that won't advance cycles or gets stuck between rinse and spin. This cycle selector switch controls washing cycle progression.
Washer won't spin or agitate? A failed drive motor is often the cause. This motor assembly restores drum rotation and agitation for reliable washing.
Washer won't spin or agitate? A failed drive motor stops drum rotation entirely. This replacement motor restores wash and spin cycles. 2-hour DIY fix.
Shield cap for laundry center washers. Covers and protects internal components. Replace if cracked, broken, or missing to maintain proper enclosure.
Right hand side. For screws use WPW10119828.
With the parts supplied from your company. The lady that took my order was good at her job. All the parts were correct and fit. I thank you for the service that recieved. Read more
This is a push button switch used to start and stop the wash cycle on a washing machine. It mounts on the control panel and engages the machine's control circuit when pressed. Replace this button if it feels loose, does not click properly, or the washer fails to start or stop when pressed.
Replaced the rubber button. Read more
4 - Position Switch
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.