Jdb85900awb Parts

Color: Stainless   Note: Comes with Allen wrench, spare set screw, and instructions.

This part is the rinse-aid cap/knob that seals the dishwasher's rinse-aid reservoir in the door-mounted dispenser. A secure cap prevents leaks and evaporation so rinse aid dispenses properly, helping reduce spots and improve drying.

• Seals the rinse-aid fill port on the dispenser to prevent leaks and evaporation
• Helps the dispenser meter rinse aid during the final rinse
• Common symptoms of a bad/missing cap: loose or cracked cap, rinse-aid odor or residue inside the door, rinse aid depleting quickly, increased spotting on dishes
• Restores proper sealing and helps maintain consistent drying performance

• Disconnect power at the breaker and turn off water before servicing
• Open the door, remove the old cap by turning counterclockwise
• Clean the sealing surface; install the new cap by hand and tighten until snug—do not overtighten
• Run a quick cycle and check for leaks around the dispenser

This replacement shield fits over the heater/probe area to provide a protective barrier. It helps prevent direct contact and excessive radiant heat exposure, protecting nearby components and supporting accurate temperature sensing for consistent operation. What it does:

• Shields the heating element and adjacent temperature probe/sensor area
• Helps prevent heat damage to nearby plastics, wiring, and components
• Reduces the chance of items contacting or striking the heater/probe
• Common signs it's needed: cracked, warped, or missing shield; discoloration; rattling or an exposed probe/heater area

• 1 shield

• Disconnect power and allow all heated parts to cool before servicing
• Access the heater/probe area and note the original shield orientation
• Seat the shield fully; secure with existing clips/fasteners if applicable
• Verify clearances around the heating element before restoring power

Bottle with brush. Color: Black. Size: 0.6 fl.oz.

This compression tube nut secures water inlet tubing to a threaded fitting to create a reliable, leak-resistant seal. Replace a cracked or stripped nut to stop drips at the connection and keep your appliance's water system working properly.

• Compresses the tubing against the fitting to seal the water line at the inlet valve, filter head, or other water-system connections
• Helps correct leaks at the water line connection point
• Replaces nuts that are cracked, cross-threaded, or deformed
• Common symptoms: water dripping at the connection, difficulty tightening the line, or a poor seal after reassembly

• Shut off the water supply and disconnect power before servicing.
• Slide the nut onto the tubing first, seat the tube fully on the fitting, then hand-tighten and snug with a wrench; do not overtighten.
• Inspect and reuse the existing sleeve/ferrule and tube insert if in good condition; replace if worn.
• Restore water and check for leaks at the connection.

This dishrack replaces a damaged or rusted rack in your dishwasher. Restoring a true-to-spec rack keeps plates, bowls, and cookware secure and properly spaced so the machine can clean effectively and the rack moves smoothly on its tracks. What it does:

• Organizes and supports dishes and cookware during wash and dry cycles
• Maintains proper spacing for spray coverage and drainage
• Interfaces with the rail system to slide in and out when paired with the correct rollers/stops for your model
• Common symptoms: rusted or broken tines, deteriorated rack coating, misshapen frame, rack falling off tracks or not sliding properly

• 1 dishrack

• Disconnect power to the dishwasher before servicing
• Open the door; pull the existing rack out. For upper racks, release/remove rack stops or end caps; for lower racks, lift straight out
• Transfer any reusable components (rollers, clips, fold-down tines, silverware basket) from the old rack
• Slide the new rack onto the rails and reinstall stops; verify smooth travel before running a cycle

The door balance mount is the side-frame bracket that supports the dishwasher's door counterbalance system. When worn or broken, it can let the door drop, slam, bind, or feel heavy. Replacing it restores smooth, controlled door movement. What it does

• Anchors the door springs and balance link/cable to counterbalance the door's weight
• Helps the door open and close smoothly without dropping or slamming
• Guides the balance link for consistent, quiet movement
• Common symptoms: door feels heavy or uneven, falls open, won't stay put, or makes grinding/squeaking noises; visible damage to the bracket or rollers

• One door balance mount (bracket)

• Disconnect power and shut off water before servicing
• Pull the dishwasher out slightly to access the side where the mount is installed
• Carefully relieve spring tension; note link/cable routing before removal
• Transfer the spring/link to the new mount, secure the bracket, and check door balance on both sides

This fold-down tine pivot for the lower dishrack acts as the hinge and latch for the adjustable tine row. Replacing a worn pivot restores stable loading and allows the tines to flip up or down as designed. What it does:

• Supports and pivots the fold-down tine row on the lower dishrack
• Holds tines in either position to accommodate different dish loads
• Common symptoms: tines won't stay upright, adjustable row detaches, cracked or missing pivot
• Helps prevent dishes from tipping during wash cycles

• Disconnect power and water supply to the dishwasher for safety; remove the lower rack
• Release the old pivot's locking tabs and slide it off the rack/tine row
• Align the new pivot with the rack wires and tine row; snap securely into place
• The tine row pivots smoothly and holds in both positions

This inner door seal forms a moisture barrier between the dishwasher tub and the door assembly, helping keep wash water and steam contained. Replacing a worn seal can stop drips at the door and protect internal components.

• Seals the joint along the inner door to contain wash water and steam
• Helps prevent door-area leaks or drips during cycles
• Blocks moisture from entering the door cavity where electrical parts reside
• Common signs: water at the bottom/sides of the door, damp control area, visible wear/flattening or tears on the seal

• Disconnect power and turn off water supply before servicing
• Open the door and remove perimeter screws to separate inner/outer door panels
• Remove the old seal; clean the mounting surface and note seal orientation
• Press the new seal firmly into place, reassemble, and run a leak check

Size: 1/4 inch hex head, 10-12 x 1/2 inch.

This replacement screw secures appliance components, panels, and brackets. It restores a tight, reliable hold when an original fastener is missing or damaged, helping eliminate rattles, gaps, or shifting parts.

• Fastens two or more parts together inside the appliance
• Helps keep panels, brackets, or trim securely in place
• Can reduce vibration, rattling, or loose handles caused by missing/loose screws
• Replaces worn, stripped, or corroded fasteners

• Disconnect power and shut off water supply before servicing
• Match location and orientation to the original fastener
• Start threads by hand to avoid cross-threading; use the correct driver bit
• Tighten snugly—do not overtighten to prevent stripping or cracking

Includes vinyl rack repair touch up paint and tine tip covers. Color: Grey

12 Ft in length

This hose clamp secures dishwasher hoses to fittings and ports to maintain a tight, leak-resistant seal. Replacing a worn clamp helps prevent drips and loose connections that can cause water under the unit.

• Secures drain or circulation hose to the pump, sump, or other dishwasher fittings
• Helps maintain a watertight seal at hose connection points
• Can help resolve water dripping from a hose joint or a loose hose
• Replace if corroded, deformed, cracked, or no longer holds tension

• Disconnect power and turn off the water supply before servicing
• Place a towel or shallow pan to catch residual water when removing hoses
• Fully seat the hose on the fitting, position the clamp over the barb/connection, and secure firmly
• After reassembly, run a brief fill/drain and check all connections for leaks

Includes two screws, two clamps, and undercounter mounting brackets.

This dishwasher circulation pump and motor assembly moves wash water through the spray arms during the cycles. Replacing a failed or noisy unit restores proper water flow, spray pressure, and reliable cleaning performance.

• Circulates water from the sump through the spray arms during wash and rinse
• Provides the pressure and flow needed for effective cleaning
• Common failure symptoms: little or no spray action, poor cleaning results, loud humming/rumbling/grinding during wash
• Water leaking from the pump area can also indicate a problem with this assembly

• Disconnect power at the breaker and shut off the water supply before servicing
• Access from the bottom/front; remove the toe panel and pull the dishwasher out if needed for clearance
• Expect residual water; place towels or a tray to catch spill, and note wire/connector orientation before removal
• Ensure all connections and seals are properly seated; run a short fill/rinse to check for leaks before reassembly