Ks5m Parts

Maytag Dishwasher (about 5 years old). Some of the buttons had stopped functioning. Then the Start button began choosing whether or not to work. Eventually it would not start at all. Upon removing the control panel, the first thing I noticed was that the brackets that hold the two lower screws were broken. (So this was the reason that the door was so hard to open from the time it was new.) I trouble shot the thermal fuse, the door-latch switches, and inspected the control board trying to find... Read more

Ordered Bake Element, Y04100019 (Whirlpool AP4283614) to replace a broken bake element on my 30-year old Jenn-Air Model S125 Downdraft Slide-in electric range. Received the element very quickly but it had been damaged in shipping. Called AppliancePartsPros to report this and they quickly shipped another element - very easy process. To install the element, I turned off the power to the range, put on rubber gloves (just in case) and removed the two sheet metal crews at the rear of the oven -... Read more

Removed the handle with two screws on the inside front and pulled out the custom wood panel. Pulled the compactor out from under cabinet. Tipped it over on back of unit, supporting it with a little foot stool. Unscrewed two lower screws at bottom of unit holding black trim panel (that held wood panel in place) and lower black rubber flap. Removed two screws on lower outside side of unit that held the foot pedal. Slid off black U shaped metal frame from top of compactor towards bottom. Slid on... Read more

Ordered part from AppliancePartsPros.com and received it 2 days later. Put the part in, fit like a glove, water and ice cube maker working flawlessly again with no leaks. Thanks. Read more

• Leaking

Replaced the broken parts. The water leak was caused by the drain valve not directed into drain pan Read more

Replaced the water tube that went from the plastic tubing to the ice cube tray. Found that even though it was the same exact length as the original, there was only an extremely small gap from the end of the tube to a splash board. This may have been the root cause of my problems. Read more

• Little to no heat when broiling

Turned off the oven power at the breaker box. Removed the (2) 1/4" screws holding the front support bracket and removed the front support bracket. (This bracket is necessary as the broiler element is in the top of the oven) Then I removed the (2) 1/4" screws holding the element against the back of the oven, gently pulled the element away from the back of the oven to expose and unplug the (slip on) electrical connections, and removed the burned out element. Contrary to some home projects I... Read more

Ordered the gasket kit. The shipping time was quick. The installation was more difficult than anticipated. The inside of the door had to be removed there were about 30 hex head screws. the new gasket then had to be fitted to the interior of the door and then placed on the outer part of the door and the screws replaced. The screw replacement took longer than anticipated as there were eight corner screws that were very difficult to manage because of the inside design of the gasket. The screws all... Read more

The website made it very simple to find the replacement shelves I needed. I measured them before my order and checked to see if they were the right size. When they arrived I simply took them out of the package and lined up the shelf tabs in the slots of the refrigerator, and pushed down to install. Easy! Read more

Ordered new Evaporator part and Drier from Appliance Pros. The part arrived earlier than expected and was properly packaged. I had both parts installed by a professional as they required a level of expertise above my capabilities. Works perfectly. Read more

Popping the old draw glides off was the toughest part of the job, ad even that was fairly easy, once I noticed the little retaining tabs near the front of the drawer. Pushed in on the tabs, while pushing back on the drawer glide rail and it popped right off. One minor problem I did note: When the rollers were installed on the shoulder screws, they would not turn. One roller just had a burr around the inside edge of the hole. The other the entire bore was a bit undersized, creating a snug fit.... Read more

This trash compactor is in our vacation home. We never use it and now we are selling the house. When I looked to replace it I was amazed at how expensive a new compactor would cost. I found the serial number on the current compact entered it and your web site came up. Your schematics were excellent and made the repair very easy! Read more

• Freezer section too warm
• Fridge too warm

After watching numerous videos I was able to discern that the problem was with one of the following: the timer, the heater, or the thermostat. a short time check showed me that the timer was working so that narrowed it down to the other two. Not having the necessary tools to check those two I ordered both parts. Once the parts came and I took out the old parts it was quite evident that it was the heater since it had black burn marks on it. I decided to install the thermostat also since it... Read more

• Door won't open or close

Temporarily stuck a BMW lug bolt through the bracket and pivot opening to secure the door on the base, then waited just 3 days for the exact parts to come in from AppliancePros. Searching for the appliance model number brought me to the Appliance Pros website where finding the exact parts was quick and easy. Getting the correct part installed was a bit more involved as I had to remove and reinstall the bracket once the hinge pivot was installed, but it was quick and easy with my son holding the... Read more

Popping the old draw glides off was the toughest part of the job, ad even that was fairly easy, once I noticed the little retaining tabs near the front of the drawer. Pushed in on the tabs, while pushing back on the drawer glide rail and it popped right off. One minor problem I did note: When the rollers were installed on the shoulder screws, they would not turn. One roller just had a burr around the inside edge of the hole. The other the entire bore was a bit undersized, creating a snug fit.... Read more

Checked out the video on your site on how to disassemble the ice maker. Was really easy when you know the correct sequence. Only 3 screws and it's out of the freezer. Disassembled the ice maker on my kitchen counter and replaced the ice stripper. Reassembled and installed back in my freezer. It is as good as new Read more