Ksc25inss00 Parts

Replaced relay and capacitor attached to compressor Read more

Used U-Tube diagnostic clips to diagnose that most likely problem was a worn Evaporator Fan Motor which is located in the freezer back wall, located in the top third of the unit. I removed 6 hex head screws from the freezer's interior back panel that covers the evaporator coils. The cover is located in the lower 2/3s of the back wall. Removed all shelving. Also removed screws that held in shelf supports on one side of the freezer wall. I then removed the back panel. You may need to... Read more

Removed the back cover to access the fan area. Clean the area with brush and vac first. Unplugged the Refrigerator. Used a socket set with 1/4" socket. Had an extended and a standard socket. Removed the condensate plastic drain from the bottom of the refrigerator to have more access to the fan. Unplugged the fan motor. Removed the two screws holding the fan in place. Removed the fan unit from the condenser side of the bracket. Place new fan on the fan and installed exactly the way I removed the... Read more

Watched a video. Ordered a thermistor. Made the fix. $100 total including expedited shipping. Diagnosing the problem was more stressful than fixing. Read more

My KitchenAid refrigerator was not cooling, but the freezer was working perfectly. The help section here listed three parts that could be defective–defrost thermostat, evaporator fan motor and blade, and air diffuser/damper control–so I replaced them all. The videos were EXCELLENT, and despite the difficulty I had squeezing my shoulders into the small freezer compartment, I installed the parts and my refrigerator is cooling perfectly! THANK YOU FOR THE EXCELLENT REPAIR VIDEOS! I am so happy... Read more

• Noisy

I pulled the refrigerator out, removed the back panel, disconnected the fan motor. I did not know how hard or easy it would be to remove the fan from the motor shaft so I removed the motor with the fan attached and then removed and replaced the fan. This would not be necessary if you have a lot of strength, but if you need leverage to push the fan down on the shaft you might want to disconnect and remove the motor fan assembly too. After replacing the motor assembly and reconnecting I tested by... Read more

• Ice maker won't dispense ice

My LG electric dryer stopped drying the other day and I searched on line for suggestions on what may have caused it to stop working. I came across AppliancePartsPros.com and quickly found some of the most common issues with my LG dryer. The problems were listed in the order of most common occurrence, and had extremely helpful and detailed instructions on how to not only diagnose the problem, they also showed exactly how to access and repair the issue. Unfortunately, it was late on a Thursday... Read more

Touch up paint Read more

Replaced It With New One Read more

New mounting screws and handle. BTW, the parts have been redesigned to be more robust. Easy fix and the Refrigerator// Freezer look like new. Read more

The problem was that the motor coupler & shaft had a tiny bit of rust at their union. With the weight of the ice bin it rusted in the lowest position. This didn't allow the motor coupler to float on the shaft. There is a spring inside the shaft that pushes up on the motor coupler keeping it engaged in the ice bin coupler above. This coupler in turn rotates the auger in the bin to dispense the ice. I removed the motor coupler & shaft, tapped the coupler loose and filed off the rust. This allowed... Read more

I had to replace my frig and the upgraded model didn't come with a dairy bin. I found a review for the model in which someone had done the research and found that the Kenmore Elite had a model of refrigerator that was designed like the Whirlpool but came with the bin. He ordered it for his Whirlpool and he says it fit. I ordered one and it fit on the top notches but due to the design, it would not open. I just shifted a door shelf up to the top and put the dairy bin under it and it works fine. Read more

Replaced all filters Read more

Replaced it Read more

I purchased replacement parts to completely replace basket, face plate, and rollers. I received exactly what I ordered. The only problem I had was removing the part(s) from the shipping box. I thought the part came assembled (as rollers had been installed onto the basket), but the face plate had not been snapped into place. When I removed everything from the shipping box as one piece, the face plate fell off, hit the tile floor, and cracked. Bummer. Since the original face plate was in good... Read more