Kscs2sfkss01 Parts

Cut piece to fit Read more

The fix was quite simple/ get a new bin and hang in place. Your service staff were very helpful in supplying me with the proper piece for the job.. My sincere thanks in making this totally painless Read more

All this occurred after our utility had to cut off our water for 2-3 hours. We almost ordered a new ice maker, but thankfully someone had their repair story posted. Based on that story, we ordered a new ice maker supply line and a new water inlet valve for our Kitchen Aid refrigerator. After turning off the water to the refrigerator we noticed that the water supply line had almost burst right above the ice maker, so we thawed that out with a hair dryer, then replaced that line first. Removed... Read more

The video was very helpful, but my KitchenAid model required slightly more steps. Only the two screws in front held the filter housing, same as the video shows, but it has to be removed from the rear. My model did not have the wire brace, only the two front screws held the housing. Shut the water off and pull the electrical plug. Remove the two screws holding the filter housing in the front. Remove the lower panel in the rear at the bottom of the refrigerator. Remove the two screws holding the... Read more

Replaced water reservoir that had become contaminated with ??? Also had to replace the water filter, because the water contaminated it also. Cost was about $150, for two filters and the reservoir. The first filter was replaced because I did not know the reservoir was contaminated, and no water was coming out of the dispenser. Since the water in the ice maker did not come through the reservoir, there was no smell or contamination there. The new filter enabled water to come through the dispenser,... Read more

Found the parts in the diagram of my fridge and simply installed it very easy Read more

Easy to remove the metal parts from the old bin. The only problem was that the screw that holds the adapter has red thread locker and screwdriver rounded off the head of the screw. Drilled the screw and heated the screw to loosen the thread locker and used an ease out to remove the screw. Read more

Replaced icemaker and shutoff arm. Easy project. Read more

Replacing the cold control solved the problem. While i was at it i also replaced the defrost timer and installed a new ice door. Read more

I replaced the freezer door seal. Read more

Replaced entire ice maker. A couple of important points. (1) The ice maker module does not include all parts. The door flap for example is not included. So save all plastic parts from the old unit including screws. The biggest installation problem was the power cable. There was little room on the side of the ice maker for the cable and connectors to fit. Make sure the connector that mates with the refrigerator cable is seated onto the plastic housing and does not stick out or dangle out.... Read more

Although the solenoid I purchased did not fix the problem, nor the "mother electronic board", or the motor, my experience with Appliance Parts Pros has been excellent. Extremely easy to look-up parts for my model refrigerator. Best part is their video instruction that gives you step-by-step hands-on how to remove and install. I would highly recommend these folks. If a lady such as myself can do repairs based on their instruction, anyone can. Thank you for providing such an informative... Read more

Well, I took it out (it slides out) to get a good look at it,so i could ref pictures on your site..naturally I had serial/model of refrig,and thats mandatory to get the right part. It came in 2 days,,and being just the bucket, it took only a few minutes to transfer the auger assembly/cube/crusher.... into the new one, 6 screws total..Your site has excellent vids on DIY.......I HIGHLY reccomend. Whole process was'nt over 15 minutes, piece of cake....And NOW i can go back to my nightly 'scotch... Read more

Added a new shaft as the old shaft had worn down...........works perfect now. Thank you Easy fix ....no more than 10 mins. Read more

• Ice maker dispenses too much ice
• Leaking
• Ice maker not making ice

Watched online video and worked along - it was easy and quick - I was amazed! Read more

• Ice maker won't dispense ice

I first thought it was the auger in the ice container so I changed it and it was not the problem. I then talked to ApplianceParts customer service that it might be the yoke on the motor that turned the auger or even the motor itself even though it worked. I ordered the parts, the yoke was supposed to be able to be changed by itself but mind would not come off the motor shaft so I had to cut it off just to remove it from the unit so I had to change the motor anyway because of this. So I advise... Read more