Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
The Idler Shaft Retaining Ring is an OEM replacement part for Whirlpool dryers. Also called an "E" ring, it is a sealing gasket positioned between the front and rear housing omponents. Maintaining an airtight seal prevents gas leakage and promotes efficient drying performance.
Causes of a bad retaining ring commonly involve compression loss of the rubber gasket material over many years of heating cycles. Exposure to petroleum-based cleaners may prematurely deteriorate the seal as well.
Symptoms of a failed 'E' ring include:
This OEM Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore gas dryer models.
First replaced the drum rollers...that wasn't it..took dryer back apart and spun the belt tension wheel by hand (should have done this the first time I took the dryer apart) and it squeaked. so I ordered the full parts: wheel, idler arm, idler spring, arm sleeve, E ring..Put it back together and whoa..no more squealing!! Read more
Mounting screw for refrigerator ice maker assembly. Secures components to maintain structural integrity. Replace if lost, stripped, or corroded.
Took off the freezer door, took off the top hinge on the refrigerator door, replaced the handle, re-installed the top hinge and the freezer door. This is a two person job - one to remove the top hinge and replace the handle, while a second person holds the refrigerator door in place. Replacing the handle was easy. The most irritating part was figuring out what parts to order. The drawing of the refrigerator door (Drawing # 4) used to figure out what parts to order was not clear. I paid $8... Read more
Freezer too cold or fridge too warm? This temperature sensor thermistor monitors compartment temps and signals the control board. DIY-friendly repair.
The site came up on a Google search suggesting a new air diffuser which was indeed the problem. I got a thermistor too just in case but probably want needed. Saved a fortune compared to a repair man and was able to cancel an order I had for a new unit saving over $1200+! Very happy with the whole process and videos on you tube etc. Great site! Thanks! Read more
The Ice Maker Water Line is an OEM part for Whirlpool refrigerators. It supplies water from the household plumbing to the ice maker, ensuring a consistent and reliable production of ice cubes. This kit includes a 1/4-inch plastic water line that is approximately 72 inches long. The tubing will need to be cut to match the desired length.
Causes of a bad water line can include wear and tear from prolonged use, kinks or bends restricting water flow, or leaks due to punctures or cracks. A compromised water line can result in inadequate ice production or water leaks.
Symptoms of a bad ice maker water line include:
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
I watched your how-to video. It explained the repair PERFECTLY. It was an easy repair and the video was very detailed. It took the guesswork out of the repair. I was done in 5 minutes. thanks for taking the time to post videos for your parts. I'll shop here again. Best Regards, Chad M Read more
Light bulb socket holds and powers the bulb inside your refrigerator. Replace if lights don't work despite new bulbs or if socket is cracked or damaged.
Dropped light panel by removing two screws with socket set. Unplugged two terminals and unclipped the light socket from the base. Then just clipped the new socket onto the base, plugged the connectors onto the terminals and remounted the base. Total job was less than 15 minutes. Read more
Cap that attaches to your refrigerator's water filter cartridge for easy installation and removal. Replace if cracked, broken, or missing from filter.
I was able to put the cap on the filter and install it on the fridge Read more
Illuminates appliance interior. Replace when burned out or dimming. Verify wattage and base type match your model before ordering. Easy DIY fix.
If your fridge isn't cooling or freezer is making loud noises, the evaporator fan motor may have failed. Moderately easy DIY repair with video guide.
After checking the suggested fixes and parts on Appliance Parts Pros, I ordered the defrost thermostat and evap motor for my refrigerator, a Kitchen Aid KSSC42QTS00. Installation was very easy, simply emptying the freezer and removing the access panel in the back bottom half. Upon getting everything open, I found out that the existing evap motor was working fine, so I didn't install that part. I did install the defrost thermometer, which was a 5-minute process. I also cleared out the vent... Read more
Fix a refrigerator that won't cool or has inconsistent temperatures with this inverter control board. Moderate DIY repair with step-by-step video guide.
Replaced the Inverter box Read more
Protective cover for the ice maker's infrared emitter sensor in the freezer compartment. Replace if cracked, broken, or missing to shield the sensor.
Followed the video you provided. Read more
The Spring is an OEM part for Whirlpool refrigerators. It is a small but important internal part that applies pressure to dispense cubed or crushed ice from the refrigerator door. The spring is located within the ice dispenser mechanism and works with a lever to push ice out through the dispenser chute upon activation.
Causes of a bad spring can include wear and tear over time, putting undue pressure on the dispenser by jamming items into the chute, or damage from excessive force applied during dispensing.
Symptoms of a bad spring include:
This OEM Whirlpool part is compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
The problem was that the motor coupler & shaft had a tiny bit of rust at their union. With the weight of the ice bin it rusted in the lowest position. This didn't allow the motor coupler to float on the shaft. There is a spring inside the shaft that pushes up on the motor coupler keeping it engaged in the ice bin coupler above. This coupler in turn rotates the auger in the bin to dispense the ice. I removed the motor coupler & shaft, tapped the coupler loose and filed off the rust. This allowed... Read more
Freezer frosting up or refrigerator not cooling? The defrost timer controls the defrost cycle. DIY-friendly repair, typically 30 minutes to install.
Replaced the heater, timer, and wiring harness Read more
Fix a refrigerator that won't dispense ice with a new auger motor. Typical repair takes 30 minutes with basic tools. Video instructions available.
Very easy to replace. Take off cover to auger compartment. Unplug power connector from auger motor. Remove four screws holding auger motor to refrig. Put new auger motor in place, insert screws, insert power connector, replace cover. Use ice maker! Read more
Fix loud grinding noises or warm fridge temps with this evaporator fan motor. Circulates cold air over coils. Moderate DIY repair, 30-60 minutes.
The fridge is 20+ years old in a home we recently moved into. It sounded like a motor getting stuck on something or grinding weird... was hoping it wasn't something more serious. Found this site, clicked 'noisy' and got the replacement evaporator fan motor blade as well as the motor evaporator. Turned out I didn't really need to replace the fan blade, but since I had it and ours was old, figured I might as well put in the new parts. Followed the videos here, which were really helpful. The... Read more
Stores and chills water before dispensing. Replace if cracked, leaking, or causing slime/film buildup in dispensed water. Installs inside refrigerator.
After watching installation videos on each felt I could pull it off and ordered and received replacement water reservoir and water dispenser tube assembly. Reservoir installation went off without a hitch outside of the added step of the need to remove the entire main in waterline assy in order to access the connectors which also were not as represented in video, in that they were not the press-to-release type but standard threaded compression types. Water Dispenser tube/spout assembly was much... Read more
This screw is used to secure the handle end cap to the center of the door. The screw size measures 8-18 x 1/2 inches.
This was actually one of the easiest fixes I’ve done. All that was required was to remove 3 screws to remove the broken part. I used a pair of pliers to remove the moisture sensors from the broken part to the new one. Read more