Kude60hxss Parts

The Diverter Motor is an OEM part for Whirlpool dishwashers. It controls the movement of the diverter disc, which directs water flow to different spray arms during the wash cycle. This ensures that all areas of the dishwasher receive adequate water pressure for effective cleaning.

Causes of a bad diverter motor can include electrical malfunctions, wear and tear from frequent use, or damage from water exposure. A faulty diverter motor can prevent the proper distribution of water, leading to poor cleaning performance.

Symptoms of a bad diverter motor include:

• Dishes not being cleaned properly
• Unusual noises coming from the dishwasher during operation
• The dishwasher not advancing through cycles correctly
• Water not reaching all areas of the dishwasher

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Note: Includes wire harness WPW10083167, Drain cap part number WPW10193605, and the shaft seal has been incorporated into sump housing, not available separately.

Leaking from the bottom or center of your dishwasher? The sump housing with included shaft seal often fixes this issue. DIY-friendly with video guide.

Dishes not cleaning or soap not dissolving? This sump and motor assembly restores water circulation to spray arms. Moderate DIY repair fixes leaks too.

This hose clamp secures dishwasher hoses to fittings and ports to maintain a tight, leak-resistant seal. Replacing a worn clamp helps prevent drips and loose connections that can cause water under the unit.

• Secures drain or circulation hose to the pump, sump, or other dishwasher fittings
• Helps maintain a watertight seal at hose connection points
• Can help resolve water dripping from a hose joint or a loose hose
• Replace if corroded, deformed, cracked, or no longer holds tension

• Disconnect power and turn off the water supply before servicing
• Place a towel or shallow pan to catch residual water when removing hoses
• Fully seat the hose on the fitting, position the clamp over the barb/connection, and secure firmly
• After reassembly, run a brief fill/drain and check all connections for leaks

Fix intermittent power issues or loose connections in your dishwasher. This wire connector restores secure electrical contact between components.

Secures trim and panels in dishwasher assemblies. Replace if clip is broken, missing, or worn. Prevents loose parts and rattling during operation.

Restores visible feedback on your dishwasher control panel. Replace when burned out or non-functioning to see cycle status at a glance. Verify fit by model.

Touch-up paint for restoring chips, scratches, and nicks on painted appliance surfaces. Covers minor cosmetic damage on exterior panels and finishes.

Secures knobs, trim, or linkages to shafts inside your dishwasher. Replace if broken, cracked, or missing to prevent components from loosening.

This is a stainless steel door handle kit for a dishwasher. It attaches to the front of the dishwasher door and provides a grip for opening and closing the unit. Replace this handle if it is cracked, discolored, loose, or broken, making it difficult to properly open or secure the dishwasher door.

Drain hose for dishwashers that removes wastewater after each cycle. Replace if cracked, leaking, or clogged with mineral deposits over time.

This is a small cap or plug that seals the drain pump opening on a dishwasher. It prevents water from leaking out of the drain pump housing when a secondary drain connection is not in use. Replace this cap if you notice water dripping from the drain pump area or if the original plug is cracked, missing, or no longer sealing properly.

Fix a dishwasher door that won't latch or stay closed with this strike plate. Provides the contact point for the latch to secure your door properly.

Positions and supports the dishwasher tank assembly to maintain proper alignment. Replace if worn, cracked, or missing to restore correct spacing.

This black door handle mounts to the front of the dishwasher door and is used to open and close the unit. It attaches with screws or clips and provides the grip needed to latch and unlatch the door. Replace this handle if it is cracked, broken, loose, or if the mounting points have become damaged.

Secures interior panels and trim to prevent vibration and movement. Replace when clips break or lose grip. Verify fit with your model number.