Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Broken or loose dishwasher door handle? This replacement handle restores secure opening and closing. Straightforward 20-30 minute repair with screwdriver.
Had to remove the screws that hold the dish washer to the counter top by knocking them out of the counter top. After seeing how the door handle worked I will not have to do again as all you have to do to open is stick a long screw driver up inside and push the chip and it opens. Ordered handle installed it now everything works fine. $29.00 for little plastic handle seems quiet rediculous but Kitchenaid and parts direct where $39.00 so I guess I got a bargain. As for the tools you a trox driver... Read more
Specs: 10-16 x 1/2 inch.
After shopping for a new Whirlpool Thin Twin Stack, Found appliance parts pros online and decided to take it apart to see if repair was a possibility. APPro's online instructions were easy to follow, in a couple hours it was apart, and I placed the order. Reg ground took a week from NY, so the laundry piled up that week. The parts arrived on Monday morrning, by afternoon the machine was running like new! The cause was the belt tensioner pulley had frozen. Replaced it, drum wheels,snap... Read more
Dishwasher leaking from the bottom or not draining? A worn drain cover gasket often causes leaks at the sump. Moderate DIY fix stops water pooling.
Replaced the drain & wash impeller kit. Read more
Secures the middle wash arm manifold tube in your dishwasher. Replace if cracked, broken, or split from age or heat damage. Installs on manifold tube.
Ordered parts from web sight pictures came in 2 days and with new parts repaired in about 15 minutes Read more
Provides pivot point for dishwasher door spring to reduce wear. Replace if door drops, slams, or balance is off. Confirm fit with your model number.
I ordered the parts, deciding that if one spring had broken, the other one should probably be replaced at the same time. I followed the suggestion of ordering the door spring bearing given on the ordering page, and since I had not yet pulled out the dishwasher, did not know that it was not used in this older model. However, the order arrived quickly (4 days), and they are genuine Whirlpool, made in the USA, parts. The access to the sides of the dishwasher where the springs are attached... Read more
Soap dispenser door won't latch or detergent stays in compartment? This dishwasher dispenser assembly releases detergent at the right time. Moderate DIY.
Looked online for a replacement soap dispenser. Found one on several sites but The A.P.P. site showed the part on a Parts breakdown page and showed the part item number. and the actual part number. I ordered the part and expected the part to show up in about 5-7 days, as per the receipt. The part showed up in 2 business days. I installed the part and the dishwasher works as new. Thanks A.P,P. Read more
Lower dishrack assembly for dishwashers. Holds dishes during wash and dry cycles. Replace if cracked, rusted, tines broken, or missing. Includes wheels.
We moved into a home with a nice dishwasher but the bottom rack was useless without the tines. Local appliance dealer said it would be cheaper to buy a new machine, but this was a high end machine, just a bit dated. Found the replacement at Appliancepartspros.com and for 150.00 I now have a perfectly fine new "to me" machine! Read more
includes seal
Replaced nut and then found we needed new pump. Read more
Bottle with brush. Color: Black. Size: 0.6 fl.oz.
Replaced It With New One Read more
Size: 1/4 inch hex head, 10-12 x 1/2 inch.
This trash compactor is in our vacation home. We never use it and now we are selling the house. When I looked to replace it I was amazed at how expensive a new compactor would cost. I found the serial number on the current compact entered it and your web site came up. Your schematics were excellent and made the repair very easy! Read more
Wheel and bearing assembly for dishwasher upper rack. Mounts to dishrack for smooth gliding on rails. Replace if worn, cracked, or broken wheels.
Replaced the upper dishrack assembly and its rollers. Read more
Seal gasket for dishwasher inlet base assembly. Replace if you notice leaks, moisture buildup, or debris entering internal components. Confirm fit.
1. To fix the leaks from around the door, I replaced the upper and lower door seals. These were purchased in a separate transcation, so they are not the parts shown here. The upper door seal worked as intended, but the lower seal would not stay in place on the lower edge of the door during a wash. Therefore I cleaned the grease and detergent off the old seal, and installed using silicone sealer/adhesive. The plastic edge pieces for the lower seal were supplied with the kit, and they installed... Read more
Size: 7 foot long.
Bought the parts and connected same...a breeze in finding and receiving and eventually installing these parts. Read more
Secures tine rows to your dishwasher rack in the correct position. Replace if cracked, broken, or missing to keep rack tines properly aligned.
I watched a couple of your on line videos, brought the parts and fixed the dish racks. Easy. Kitchen Aid label with serial number worn out. Read more
Almond. Size: 13 oz. can. Acrylic appliance paint.
Was able to match it pretty well the natural age difference was good. The delivery of the product was amazing it took less than 24 hours to get to me and that was standard shipping. Give you guys an A for great !! Read more
This is a genuine lock nut replacement. This is a general piece of hardware that is often used on several types of lawn and garden equipment, including in engines, housing, and other areas. The exact application of this part will vary based on the unit. The lock nut is used to create a more secure seal than a standard nut. When properly secured, the lock nut tightens to a bolt and uses an extra locking washer with teeth to ensure a snug fit.If lock washers do get damaged or lost, they need to be replaced immediately with a genuine OEM replacement. This model is compatible with all types of machines and units since it is a generic part. The washer is sold as an individual part and manufactured by Whirlpool. Lock nuts will need to be installed using a socket wrench or adjustable wrench. Pliers, a screwdriver, or another socket wrench will be needed to hold the bolt while the lock nut is being secured in place. Be sure to thread the lock nut carefully to ensure a strong seal and avoid stripping the bolt or the nut.
Ordered the roller and nut, reattached the nylon wheel that I found in the floor under the oven.This was the only website where I could find all of the parts detailed and so I knew exactly what to buy. Even the manufacturer's website didn't have this info. Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.