Kudr255wh1 Parts

This drain cover gasket seals the drain/pump cover at the bottom of the dishwasher tub to keep wash water contained. Replacing a cracked or flattened gasket helps stop leaks from the base and protects nearby components.

• Creates a watertight seal between the drain cover and sump opening
• Helps prevent leaks onto the floor or into the dishwasher base during cycles
• Common signs of failure: puddles beneath the unit, dampness in the base, or a visibly hardened/cracked gasket
• Good practice to replace when the drain cover is removed for service to ensure a proper reseal

• Disconnect power and shut off water supply before servicing
• Remove the lower rack (and spray arm if required) to access the drain cover per your model
• Clean mating surfaces; install the new gasket evenly without twists
• Reassemble and run a short cycle while checking for leaks

Dishwasher middle wash arm manifold tube holder. This holder will have a split at the 3:00 position for easy removal from the manifold tube.

This dishwasher door spring bushing—also called a door spring bearing—sits at the spring's frame anchor to provide a pivot and reduce wear. Replacing a worn bushing restores door balance and helps prevent the door from dropping or slamming open.

• Provides the pivot/anchor surface for the door spring at the cabinet frame
• Maintains balanced door opening and closing force
• Reduces friction, wear, and squeaks at the spring connection

• Disconnect power at the breaker and shut off water supply.
• Remove the toe panel and mounting screws; slide the dishwasher out slightly to access the door springs.
• Support the door, release spring tension, replace the bushing at the frame anchor, and reattach the spring.
• Inspect both sides and replace worn components in pairs to keep door tension even.

This is the dishwasher manifold tube only. It attaches to the bottom of the upper rack. For the complete kit order 675808. Also consider checking the mount that attaches this manifold tube to the dishrack. For the mount order WP8539324.

Bottle with brush. Color: Black. Size: 0.6 fl.oz.

includes seal

Size: 1/4 inch hex head, 10-12 x 1/2 inch.

This inlet base seal is a gasket that fits between the inlet base and its mating surface. Replacing a worn seal helps maintain proper airflow through the inlet path and keeps spills and debris out of internal components.

• Forms a tight, continuous seal at the inlet base-to-housing joint
• Helps preserve correct airflow through the inlet path
• Blocks liquids, grease, and crumbs from leaking into the appliance interior
• Replace if the seal is cracked, flattened, brittle, loose, or you see visible gaps

• Disconnect power to the appliance before servicing
• Remove grates/cartridges, filters, or trim as needed to access the inlet base
• Clean and dry mating surfaces; install the new seal in the same orientation without stretching or twisting
• Reassemble and verify the seal sits evenly with no gaps

Size: 7 foot long.

Almond. Size: 13 oz. can. Acrylic appliance paint.

This handle spring restores tension to the door latch handle so the dishwasher door latches securely and the handle returns to position. Replace a worn or broken spring to address loose handle feel or doors that pop open during a cycle. What it does:

• Provides return tension for the door latch/handle mechanism
• Helps keep the door closed and latched during operation
• Restores proper handle feel and return action
• Common symptoms include a loose or floppy handle, door not latching or starting, or door opening mid-cycle

• 1 spring

• Disconnect power at the breaker and shut off water before servicing
• Remove inner door panel screws to access the latch area; support the outer panel
• Note spring orientation and attachment points before removal; transfer the new spring to the same tabs/holes
• If your latch uses two springs, replace both for even tension; test latch operation before reassembly

This is a tine pivot clip that is a part of the dishrack on many models of dishwashers. The purpose of the plastic tine pivot clip is to secure the tine row onto the dishrack so it stays in the correct place. Sometimes, the tine pivot clip can be damaged or cracked through typical use. When this occurs, the tine row may move out of place and cause noise or other damage to the dishwasher. If a visual inspection shows damage to the tine pivot clip, it should be replaced.Work gloves will be needed to replace the tine pivot clip. In most cases, the replacement can be done by hand but pliers may also be useful. Unplug the dishwasher and disconnect the water before making the replacement. Open the dishwasher and gain access to the tine pivot clip. Pull it out of the dishwasher and install the new replacement part. Make sure to reconnect the water and power before use.This is a genuine OEM replacement part that is directly sourced from the manufacturer. It is sold as a single part. The tine pivot clip is designed to be compatible with dishwashers manufactured by Kenmore, KitchenAid, and Whirlpool.

This small check ball sits inside a check valve to allow one-way water flow. Replacing a worn or missing ball helps prevent backflow and supports reliable draining performance between cycles.

• Maintains one-way flow through the valve to stop water from returning after the pump stops
• Helps ensure complete, consistent draining
• A damaged, swollen, or missing ball can let water back up into the tub/sump
• Contribute to slow or intermittent draining and unusual gurgling/flow noises

• Disconnect power and shut off water before servicing
• Access the check valve assembly per your model's service information (commonly at the sump, pump outlet, or drain connection)
• Clean the valve seat/passage; remove debris that could prevent sealing
• Place the ball in the valve seat as shown in your model's parts diagram; reassemble and test for leaks and proper flow

Color: White. Includes insulation. Other colors: For almond use WP3384157, for biscuit use WP3384157, for black use WP3379920.

Color: Almond

This adjustable leveling leg threads into the appliance base to set height and stabilize the cabinet. Replacing a worn or missing leg helps stop rocking and vibration and helps maintain proper alignment for reliable operation.

• Provides adjustable support at one corner of the appliance
• Helps level the unit for correct alignment with floor or cabinetry
• Reduces rocking, vibration, and rattling noises
• Replaces stripped, bent, cracked, or missing leg

• Disconnect power and, if applicable, shut off water before servicing
• Carefully support or brace the appliance to access the base safely
• Start the new leg by hand to avoid cross-threading; adjust height gradually
• Use a level to check side-to-side and front-to-back, then recheck after positioning