Kuis15mrhb9 Parts

The Ice Machine Pump is an OEM replacement part for Whirlpool ice makers. This pump works to circulate water throughout the ice-making process. It pumps water from the supply line into the ice-making components and evaporator to form each batch of ice.

Causes of a bad pump can include mineral buildup inhibiting water flow, worn impeller or motor components reducing pumping efficiency, or damage from freezing temperatures.

Symptoms of a bad ice machine pump include:

• Inability to produce ice or complete ice-making cycles
• Erratic water flow or no water circulation
• Abnormal noises coming from the pump motor

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This start relay (EMB) energizes the compressor's start winding so the refrigerator can begin cooling reliably. Replacing a weak relay can resolve hard-start clicking and restore consistent operation when the compressor struggles to start.

• Delivers initial power to the compressor's start winding, then disengages once the motor is up to speed
• Supports reliable compressor starts and reduces repeated start attempts
• Common symptoms: clicking from the compressor area, rising refrigerator/freezer temperatures, compressor starts then stops after a few seconds, or heat damage on the old relay
• Works with EMB-style compressor connections used on select units

• Disconnect power to the appliance before servicing
• Remove the rear access cover; note wire positions; pull the old relay straight off the compressor terminals
• Seat the new relay fully on the compressor pins; reconnect the harness and any run capacitor lead exactly as removed
• Reinstall the cover and restore power; use caution—capacitors may retain a charge

The Tube is an OEM part for Whirlpool ice machines. It ensures a reliable water supply from the water valve to the ice machine.

Causes of a tube can include mineral deposits from hard water, kinks or cracks in the tube, and general wear and tear from prolonged use.

Symptoms of a bad tube include:

• Reduced or no ice production
• Water leaks around the ice machine
• Unusual noises during the ice-making process
• Smaller or irregularly shaped ice cubes

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Door Switch Assembly is an OEM replacement part for Whirlpool refrigerators. It is responsible for turning the light on when you open the refrigerator door and turning it off when the door is closed. It ensures that the light functions properly, allowing you to easily locate and retrieve items from your refrigerator.

Symptoms of a faulty door light switch include:

• Interior light not turning on when the door is opened
• Interior light staying on even when the door is closed

A bad door light switch can occur due to regular use, wear and tear, or accidental damage. If you notice issues such as the interior light not turning on or off when you open or close the door, it may be time to replace the door light switch.

This Whirlpool replacement part is also compatible with Sears/Kenmore models.
 

The Ice Machine Cleaner is an OEM replacement part for use with Whirlpool ice machines. This cleaner plays a crucial role in maintaining the efficiency and longevity of your ice machine, ensuring it continues to produce clear, taste-free, and odorless ice. Formulated to remove scale and mineral build-ups, this solution is essential for the regular maintenance of ice machines, which can suffer from lime scale deposits and other residues that affect ice quality and machine performance.

Symptoms of needing an Ice Machine Cleaner include:

• Reduced ice production efficiency.
• The appearance of scale and mineral deposits within the machine.
• Ice that tastes or smells unusual.
• Increased energy consumption as the machine works harder to produce ice.

Regular use of the Ice Machine Cleaner is vital to prevent the accumulation of minerals and scale that can lead to inefficient cooling and increased energy consumption. 

Quantity of ONE. Size: 8-18 x 5/8 inch. (#8 screw, 18 threads per inch, 5/8 inch long)

The Water Valve is an OEM part for Whirlpool ice machines. This part controls the flow of water into the ice maker, ensuring it receives the correct amount of water for ice production.  

Causes of a bad water valve can include wear and tear from regular use, mineral buildup from hard water, or electrical failures. 

Symptoms of a bad water valve include:

• The ice machine not producing ice
• Slow or inconsistent ice production
• Leaking water from the valve area
• No water entering the ice machine
• You should replace the water valve if it becomes faulty or damaged.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This 10-32 machine screw secures panels, brackets, and internal assemblies in your appliance. Replacing missing or stripped hardware restores a tight, rattle-free fit and helps keep components properly aligned.

• Provides a threaded fastener for metal-to-metal connections
• Helps maintain correct alignment of panels, brackets, and housings
• Replaces missing, rusted, or stripped screws
• Symptoms include loose or vibrating panels, gaps/misalignment, or hardware that won't tighten

• Disconnect power (and shut off gas/water, if applicable) before servicing
• Match the 10-32 thread and length to the original screw for the location
• Start by hand to avoid cross-threading; tighten snugly without over-torquing
• Retain and reinstall any original clips, spacers, or washers used in your model

This replacement tube routes water safely between internal components. Use it to replace cracked, kinked, or brittle tubing so your appliance can restore proper water flow and reduce leaks during normal operation.

• Directs water between components to support normal operation
• Helps maintain consistent flow and leak-resistant connections
• Common failure signs: cracks, kinks, discoloration, or hardening
• Symptoms include water leaks, reduced flow, or intermittent filling

• Disconnect power and shut off the water supply before servicing
• Note original routing and fitting type; transfer any clips or ferrules if present
• Cut ends square and fully seat into push-to-connect or compression fittings
• Restore power and water; check all connections for leaks and proper flow

Size: 1/4 inch. Nut for plastic water line.

The Screw is an OEM part for Whirlpool refrigerators. This screw secures the refrigerator door hinge in place, allowing the door operates smoothly and seals properly. 

Over time, screws can become loose or go missing during repairs or adjustments, which can lead to a misaligned door, compromised sealing, and increased energy consumption. 

Symptoms of a bad screw include:

• The refrigerator door seems misaligned or does not close properly.
• Increased effort needed to open or close the door.
• Unusual gaps around the door seal when closed.
• The door might squeak or make other noises during operation.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Bottle with brush. Color: Black. Size: 0.6 fl.oz.

This is an ice maker recirculation pump assembly. This part includes a motor and pump that sends water from the reservoir over the top of the evaporator plate. This forms the slab of ice that will then drop onto the cutting grid to make ice cubes.In the event that the appliance is not making ice, it could be because this part has gone bad. Some users report the pump becoming calcified and then no longer working. Whether this happens or not can depend upon the water quality. Unplug the appliance from the electrical outlet prior to attempting to replace this part. Wear work gloves for safety.This particular recirculation pump is compatible with ice cube makers that are manufactured by the Whirlpool, Kenmore, KitchenAid, and Scotsman brands. This part is sold individually and is sourced directly from the manufacturer.

This compressor overload is a thermal protector that opens the circuit if the compressor overheats or draws excessive current. Replacing a failed overload restores reliable starts and helps prevent compressor damage when your refrigerator won't cool.

• Protects the compressor by interrupting power during overheat/overcurrent conditions
• Common symptoms: refrigerator not cooling, compressor won't start, repeated clicking or brief hum then shutoff
• Mounts on the compressor terminal and works alongside the start relay on applicable models
• Built for proper fit and dependable operation in the start circuit

• Unplug the refrigerator and remove the rear access panel to reach the compressor
• Note wire positions; pull the old overload straight off the compressor pin
• Push the new overload fully onto the correct terminal and reconnect wiring/terminal cover
• Restore power and verify the compressor starts without repeated clicking

This hose clamp secures a rubber or plastic hose to its fitting to maintain a tight, leak-resistant seal. Replace a worn or missing clamp to stop drips and keep appliance water connections secure.

• Fastens a hose to a barb or port to prevent leaks
• Helps keep hoses from slipping off due to vibration or pressure
• Restores proper sealing when a clamp is rusted, bent, or stripped
• Common symptoms: water dripping at a hose joint, loose hose connection, or a clamp that won't tighten

• Disconnect power and shut off the water supply before servicing
• Place a towel to catch residual water when removing hoses
• Position the clamp just behind the hose barb/bead and secure with the appropriate tool
• Restore water and power, then run a quick check for leaks at the connection

This factory fastener is a #8-18 x 5/8-inch Type AB screw designed for appliance assembly. It secures panels and components to restore a tight, rattle-free fit and dependable alignment. What it does:

• Thread-forming Type AB design engages thin metal or plastic components
• Secures panels, brackets, trim, or covers to reduce looseness and vibration
• Replaces missing, stripped, or corroded fasteners
• Helps maintain alignment for proper operation and reduced noise

• One screw

• Disconnect power before servicing; shut off water supply if working near water lines
• Use the correct driver for the screw head; start by hand to avoid cross-threading
• Tighten until snug—do not overtighten to prevent stripping or cracking plastic
• Repair damaged holes or replace worn clips/inserts before installing the new screw

• Size: #8-18 x 5/8 in (length 0.625 in)
• Thread type: Type AB, thread-forming