Kuis18ntbi Parts

This start relay (EMB) energizes the compressor's start winding so the refrigerator can begin cooling reliably. Replacing a weak relay can resolve hard-start clicking and restore consistent operation when the compressor struggles to start.

• Delivers initial power to the compressor's start winding, then disengages once the motor is up to speed
• Supports reliable compressor starts and reduces repeated start attempts
• Common symptoms: clicking from the compressor area, rising refrigerator/freezer temperatures, compressor starts then stops after a few seconds, or heat damage on the old relay
• Works with EMB-style compressor connections used on select units

• Disconnect power to the appliance before servicing
• Remove the rear access cover; note wire positions; pull the old relay straight off the compressor terminals
• Seat the new relay fully on the compressor pins; reconnect the harness and any run capacitor lead exactly as removed
• Reinstall the cover and restore power; use caution—capacitors may retain a charge

The Tube is an OEM part for Whirlpool ice machines. It ensures a reliable water supply from the water valve to the ice machine.

Causes of a tube can include mineral deposits from hard water, kinks or cracks in the tube, and general wear and tear from prolonged use.

Symptoms of a bad tube include:

• Reduced or no ice production
• Water leaks around the ice machine
• Unusual noises during the ice-making process
• Smaller or irregularly shaped ice cubes

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This refrigerator water reservoir stores and chills water for the dispenser, helping deliver a steady, cold flow. Replace a cracked or leaking tank to stop internal leaks and restore consistent dispenser performance.

• Holds water between uses so the dispenser delivers a steady, cold supply
• Cracks or brittleness can cause leaks under crisper drawers or inside the fresh food section
• Kinks or mineral buildup may restrict flow, causing slow or no dispensing
• Freezing damage can split the tank, leading to intermittent leaks after thawing

• Unplug the refrigerator and shut off the water supply
• Remove shelves/crispers and the interior access panel as needed; keep towels handy for residual water
• Disconnect tubing and reuse existing fittings/brackets as required
• Restore water, purge air through the dispenser for several minutes, and check all connections for leaks

The Ice Machine Cleaner is an OEM replacement part for use with Whirlpool ice machines. This cleaner plays a crucial role in maintaining the efficiency and longevity of your ice machine, ensuring it continues to produce clear, taste-free, and odorless ice. Formulated to remove scale and mineral build-ups, this solution is essential for the regular maintenance of ice machines, which can suffer from lime scale deposits and other residues that affect ice quality and machine performance.

Symptoms of needing an Ice Machine Cleaner include:

• Reduced ice production efficiency.
• The appearance of scale and mineral deposits within the machine.
• Ice that tastes or smells unusual.
• Increased energy consumption as the machine works harder to produce ice.

Regular use of the Ice Machine Cleaner is vital to prevent the accumulation of minerals and scale that can lead to inefficient cooling and increased energy consumption. 

The Water Valve is an OEM part for Whirlpool ice machines. This part controls the flow of water into the ice maker, ensuring it receives the correct amount of water for ice production.  

Causes of a bad water valve can include wear and tear from regular use, mineral buildup from hard water, or electrical failures. 

Symptoms of a bad water valve include:

• The ice machine not producing ice
• Slow or inconsistent ice production
• Leaking water from the valve area
• No water entering the ice machine
• You should replace the water valve if it becomes faulty or damaged.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This replacement tube routes water safely between internal components. Use it to replace cracked, kinked, or brittle tubing so your appliance can restore proper water flow and reduce leaks during normal operation.

• Directs water between components to support normal operation
• Helps maintain consistent flow and leak-resistant connections
• Common failure signs: cracks, kinks, discoloration, or hardening
• Symptoms include water leaks, reduced flow, or intermittent filling

• Disconnect power and shut off the water supply before servicing
• Note original routing and fitting type; transfer any clips or ferrules if present
• Cut ends square and fully seat into push-to-connect or compression fittings
• Restore power and water; check all connections for leaks and proper flow

This water inlet valve regulates the flow of water into the appliance. When the control calls for water it opens; when closed it stops flow. Replacing a faulty valve helps restore proper filling and prevent unwanted leaks. What it does:

• Opens and closes to control the water supply to the system
• Helps maintain correct water flow during fill operations
• Common symptoms of a failing valve: no water enters, slow or intermittent fill, water continues to flow when off, leaks at the valve or connections, or a humming/buzzing sound with little/no water

• 1 water inlet valve

• Disconnect power and turn off the water supply before servicing
• Place a towel or container to catch residual water; relieve line pressure
• Reconnect tubing and fittings securely; do not overtighten compression nuts
• Restore water and power, then check all joints for leaks and run a test fill to purge air

Size: 1/4 inch. Nut for plastic water line.

This pump wire harness connects the pump motor to the appliance's main wiring and control, ensuring a secure electrical path. Replacing a worn, heat-damaged, or loose harness restores reliable pump operation and helps prevent intermittent failures. What it does:

• Delivers power from the control to the pump motor for proper operation
• Maintains correct connector fit and wire routing at the pump
• Can help fix: pump won't run; no draining or circulation (application-dependent); intermittent operation when wires are moved; visible melted/burned connector
• Replaces brittle, chafed, or shorted wiring that can trip breakers or blow fuses

• One pump wire harness assembly

• Disconnect electrical power; shut off water supply if working near water lines
• Note connector orientation and take photos before removal
• Route the new harness like the original using all clips/retainers; keep away from sharp edges, moving parts, and hot surfaces
• Push connectors straight and fully until they latch; never pull on wires

The Screw is an OEM part for Whirlpool refrigerators. This screw secures the refrigerator door hinge in place, allowing the door operates smoothly and seals properly. 

Over time, screws can become loose or go missing during repairs or adjustments, which can lead to a misaligned door, compromised sealing, and increased energy consumption. 

Symptoms of a bad screw include:

• The refrigerator door seems misaligned or does not close properly.
• Increased effort needed to open or close the door.
• Unusual gaps around the door seal when closed.
• The door might squeak or make other noises during operation.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Bottle with brush. Color: Black. Size: 0.6 fl.oz.

This is an ice maker recirculation pump assembly. This part includes a motor and pump that sends water from the reservoir over the top of the evaporator plate. This forms the slab of ice that will then drop onto the cutting grid to make ice cubes.In the event that the appliance is not making ice, it could be because this part has gone bad. Some users report the pump becoming calcified and then no longer working. Whether this happens or not can depend upon the water quality. Unplug the appliance from the electrical outlet prior to attempting to replace this part. Wear work gloves for safety.This particular recirculation pump is compatible with ice cube makers that are manufactured by the Whirlpool, Kenmore, KitchenAid, and Scotsman brands. This part is sold individually and is sourced directly from the manufacturer.

This compressor overload is a thermal protector that opens the circuit if the compressor overheats or draws excessive current. Replacing a failed overload restores reliable starts and helps prevent compressor damage when your refrigerator won't cool.

• Protects the compressor by interrupting power during overheat/overcurrent conditions
• Common symptoms: refrigerator not cooling, compressor won't start, repeated clicking or brief hum then shutoff
• Mounts on the compressor terminal and works alongside the start relay on applicable models
• Built for proper fit and dependable operation in the start circuit

• Unplug the refrigerator and remove the rear access panel to reach the compressor
• Note wire positions; pull the old overload straight off the compressor pin
• Push the new overload fully onto the correct terminal and reconnect wiring/terminal cover
• Restore power and verify the compressor starts without repeated clicking

This hose clamp secures a rubber or plastic hose to its fitting to maintain a tight, leak-resistant seal. Replace a worn or missing clamp to stop drips and keep appliance water connections secure.

• Fastens a hose to a barb or port to prevent leaks
• Helps keep hoses from slipping off due to vibration or pressure
• Restores proper sealing when a clamp is rusted, bent, or stripped
• Common symptoms: water dripping at a hose joint, loose hose connection, or a clamp that won't tighten

• Disconnect power and shut off the water supply before servicing
• Place a towel to catch residual water when removing hoses
• Position the clamp just behind the hose barb/bead and secure with the appropriate tool
• Restore water and power, then run a quick check for leaks at the connection

This factory fastener is a #8-18 x 5/8-inch Type AB screw designed for appliance assembly. It secures panels and components to restore a tight, rattle-free fit and dependable alignment. What it does:

• Thread-forming Type AB design engages thin metal or plastic components
• Secures panels, brackets, trim, or covers to reduce looseness and vibration
• Replaces missing, stripped, or corroded fasteners
• Helps maintain alignment for proper operation and reduced noise

• One screw

• Disconnect power before servicing; shut off water supply if working near water lines
• Use the correct driver for the screw head; start by hand to avoid cross-threading
• Tighten until snug—do not overtighten to prevent stripping or cracking plastic
• Repair damaged holes or replace worn clips/inserts before installing the new screw

• Size: #8-18 x 5/8 in (length 0.625 in)
• Thread type: Type AB, thread-forming

The Ice Thermistor Assembly is the temperature sensor your refrigerator uses to monitor the ice maker/ice compartment. Accurate readings help the control time harvests and maintain proper ice room temperature, restoring consistent ice production when the sensor fails. What it does

• Senses temperature at the ice maker/ice compartment and reports to the control
• Helps the control time ice harvests and, on some models, manage ice box airflow
• Can address issues like no ice, intermittent/slow ice production, or ice clumping/melting
• Clear a thermistor-related fault noted in service diagnostics

• One ice thermistor assembly

• Disconnect power before servicing
• Access the ice maker/ice compartment; note original sensor placement and wire routing
• Transfer any clips/insulators if present, connect the new harness, and secure the sensor in the same location
• Restore power and run the unit's ice maker/service test (if available) to operation