Lat 2500 Aae Parts

I replaced the hose between the tub and the pump. The clamp screws were quite rusted but I used a socket wrench on them since they have hex heads in addition to the screwdriver slot. If I had tried to use a screwdriver, I think it would have been difficult. I did not reuse the original clamps but replaced them with hardware store hose clamps. Read more

• Will not drain
• Burning smell
• Noisy

18 year old Maytag Atlantis top load washer had a load knocking and rattle sound with excessive vibration when the tub was spinning, but not when it was agitating. They was no water leaking. I took the front panel off and carefully listened while I ran a cycle and the loud sound sounded like it was coming from the drain pump. So I took off the drive belt and noticed that it was glazed and that there was belt material on the drain pump and tub transmission pulleys. I removed the drain pump and... Read more

• Will not agitate
• Burning smell

The washer was on, and I heard a faint humming sound in the laundry room. I went in and opened the washer and it was full of soapy water in the middle of its cycle and was not agitating. I also smelled a faint burning smell. At this point I figured the problem was a bad motor, as the washer is more than 20 years old. I have fixed it twice before, because the first time, the repairman said I should keep this washer going as long as possible. It was made to last with a metal drum, unlike newer... Read more

• Lid or door will not open
• Lid or door won't close

Wrote down model and serial number. Went to The Google to find replacement part. Among other choices, A'pplaincePartsPros.com came up. Quickly found the part. More to the point (of appreciation) is that there was a video right there on the page about how to replace this part. I hadn't tought much about it, since the lid easily came off with the pin broken. Watched the video, which was well done, and followed those steps quickly and easily. All done. The postscript is that I found the part of... Read more

• No hot or cold water
• Will not fill with water
• Will not stop filling with water

Ordered a new inlet water valve . Super fast delivery ordered on a Wednesday afternoon was here Thursday morning , standard shipping , I was impressed !! Removed the old valve , installed the new , checked for leaks no issues , washer is back on line and my Honey is very happy with me . Read more

We ordered parts from appliance parts pros and I fixed it. Read more

• Will not fill with water
• Will not agitate

First I needed to replaced the timer. However that timer is no longer available. So I was not able to buy that part. A friend encouraged me to cross reference the part number. I did and I found another timer that claimed it would work on my machine. It looked very similar. I got the timer from you guys and put it in. The water valves worked right away but the motor did not. I researched more troubleshooting ideas and discovered I had a bad lid check switch. I got a new one of those from you... Read more

• Leaking

We ordered parts from appliance parts pros and I fixed it. Read more

1. Sleeve for input, Injector valve, nozzle and seal for input fixed this problem. Probably the main part that was the trouble was a deformed Injector Valve which is a rubber tube with an internal retention groove at the wide part that grips the Nozzle. The Sleeve and the Nozzle are hard plastic parts that basically looked fine, but I replaced them anyway while I was in there. Additionally I replaced the rubber Seal for Input which seals the plastic input fitting to the tub just to make sure... Read more

Replaced with thrust bearing kit. Watched your video and it took about 10 minutes to fix. Thanks Read more

• Will not fill with water
• Won't start

No water, no electricity, nothing happened when I pulled the on knob. I replaced the lid switch. The switch arrived at my house super fast - ordered on Friday and was there on Saturday. The whole replacement process took no time at all. Read more

• Will not stop filling with water

Replaced the pressure switch which only took about 15 minutes ,was a very simple operation. tube air was backordered till 10/16/15 so checked it and found it with gunk in it ,so cleaned it out and washer works fine. can cancel tube air as i will not need now thanks for information on what part to order was very helpful Read more

1. Sleeve for input, Injector valve, nozzle and seal for input fixed this problem. Probably the main part that was the trouble was a deformed Injector Valve which is a rubber tube with an internal retention groove at the wide part that grips the Nozzle. The Sleeve and the Nozzle are hard plastic parts that basically looked fine, but I replaced them anyway while I was in there. Additionally I replaced the rubber Seal for Input which seals the plastic input fitting to the tub just to make sure... Read more

After several attempts at Local Hardware stores and Lowe's and Home Depot to find them I called AppiancePartsPros.com. I gave them the model number and what I was looking for and customer service directed me to the part on the Web site. They were extremely helpful and it was very fast and I got the parts the next day. Read more

I decided to order the siphon break kit (siphon break, washer and clamp included), a new hose, and clamp (for the bottom hose connection) as the hose was original and well over 15 years old. I probably could have used the old clamp, but decided to get a new one in case there were problems with the old during removal. The video provided by A.P.P was helpful in giving confidence this was a task that could be done by myself. As was shown in the video, the hose connection to the siphon break had a... Read more

It's working now Read more