Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
This hose clamp secures a rubber or plastic hose to its fitting to maintain a tight, leak-resistant seal. Replace a worn or missing clamp to stop drips and keep appliance water connections secure.
Replaced the tube and the clamp Read more
Indicator light lens covers the pilot lamp opening on your range control panel. Replace when cracked, discolored, or missing to restore visibility.
Purchased the triple burner and dual burner element. I added my model of stove and I was able to pull up diagrams of the stove parts. The parts were easy to find using the diagrams and the burner elements were marked 17 & 15 so I placed my order. Parts were here in a couple of days. The tricky part was figuring out how to get into the stove top. I was a few youtube videos to see different replacement. My husband and I got the stove top off and flipped it over on the counter. We looked at... Read more
This rubber seal creates a tight barrier between mating components to keep water contained and stop drips. Replacing a flattened or cracked seal helps prevent leaks and protects nearby parts from moisture-related damage. What it does:
Removed agitator, inner washer barrel, and agitator shaft then drained all the water and emulsified oil out of the transmission. Filled the transmission with new oil and then replaced the worn agitator shaft, shaft collar, shaft o-ring and stem sealing system. Read more
Hose clamp for securing water supply and drain hoses on the washer. Provides leak-free seal at hose connection points.
Replace faucet adapter, replace fill and drain hose assembly. You must remove outer cabinet to be able to route new hoses and access hose connections under tub. Read more
Fix washer overfilling or not filling properly with a new water level pressure switch. Controls fill shutoff and cycle transitions. DIY repair.
Replaced both, the water level switch and the water level hose. Watched the how to video first on your site and made the repair easy. Read more
Washer won't start or spin? A faulty lid switch prevents operation when the lid position isn't detected. Simple clip-in replacement, typically done in 10 minutes.
Took off the back of the top pushed the switch forward and lifted it out after I unplugged it. Put the new switch in the opposite of how I took it out, plugged in the wires put the back on and finished my laundry. Read more
Washer won't start or spin? A broken lid switch actuator prevents the safety switch from engaging. This plastic striker restores proper operation in 5 minutes.
Replace the broken switch Read more
Replace a worn rear self-leveling leg to restore a stable, level appliance. This foot supports the back of the cabinet and automatically compensates for floor unevenness to help reduce vibration, rocking, and noise during operation.
I followed the Appliance Parts Pro's advice videos for the Maytag MAV6451AWW Atlantis washer on replacing the snubber ring and the suspension springs. Everything went just fine except replacing the two rear most suspension springs. None of the videos illustrated REINSTALLING the REAR springs which is extremely difficult because you can't get enough leverage with your arm extended. Observing my frustration, my wife recommended taking off the back side. You can't simply take off the back,... Read more
One piece. Works on most Maytag washers. Color: white. It measures about 5 inches in diameter, and 5-1/2 inches high.
New parts did the trick. Very easy to replace. Did not need to replace the base agitator, the fabric dispenser, or the screw; but, while it was apart it was simple to do. Read more
Leaking water at the tub ring during fill? This lower water injector channels incoming water into the tub. Simple 30-minute DIY repair with basic tools.
Simple. Remove top back panel. (4 screws) Remove old injector. (1 nut screw.) Rotate to remove. (Other side is a tab in a slot.) Unsnap the upper injector. Snap upper injector on to new lower injector. Replace in reverse order. Run washer, look for leaks. Read more
Fix a washer that won't advance through cycles, fills but won't spin, or stops mid-cycle. This timer controls wash, rinse, and spin sequences. 30-minute DIY repair.
Replaced the main timer / control. Read more
Replacement mounting bolt for washer outer tub assembly. Secures tub components together with nut. Replace if rusted, stripped, loose, or missing.
We watched the video before we purchased the parts for this project. We wanted to make sure exactly what parts we would need. Thanks for having this information available. We purchased the mounting stem repair kit,,tub bearing kit, 3 new bolt/washers that hold the outer tub in place and the spanner wrench. Cleaned everything... NOTE :TAKE THE TIME TO CLEAN YOUR FILTERS ON THE BOTTOM. Thing went back together smoothly. We refereed back to the video when in doubt. Total repair $118.00... Read more
This washer drain hose routes wastewater from the drain pump to your standpipe or laundry tub. Replacing a cracked or kinked hose restores reliable draining and helps prevent leaks during the spin/drain cycle.
Bought a new hose and took one small cover off the back of machine, used pliers to remove clamp, took off old hose, put on new, replaced clamp, replaced cover and was done. Five minutes tops. Read more
To order indicator lens use WP22001948.
This water valve kit regulates the flow of hot and cold water into your appliance during fill. Replace a weak, leaking, or stuck valve to restore consistent fills and proper shutoff, resolving common no-fill, slow-fill, or seeping issues.
Removed old water valve and replaced it with new one. Reconnected wiring and water lines. Everything is working fine now. Read more
Mounting bolt secures the tub and internal components in your laundry center. Replace if stripped, rusted, or missing to restore stable assembly fit.
Purchased and installed new tub bearing and seals. Decided to replace the tub bolts as well, since I had it apart. Now if I could just find a new outer tub (which the manufacturer has discontinued). Appliance parts pros has a great "how to" video which made it simple! Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.