Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
This small spring clip secures the top panel of the dryer to the cabinet frame. It snaps into place to hold the top firmly shut during operation. Replace this clip if your dryer's top panel feels loose, pops open during use, or won't stay latched when closed.
Located model number and went to Appliance Parts Pros.com to check the repair instructions on belt and motor. Used the suggestions to diagnose problem as a broken belt. I also ordered two top locks to replace the originals that were very brittle plastic that broke when I opened the dryer. Ordered the parts on Presidents Day, and received the parts the next day. The dryer was back in service in 24 hours. Read more
The Start Switch is an OEM replacement part for Whirlpool dryers. It is an electronic component responsible for initiating the heating elements and tumble cycles upon user command from the control panel.
Causes of a bad start switch involve general wear over extended use. Failure of the internal conducting surfaces interrupts circuit activation as well.
Symptoms of a bad start switch include:
Note: This dryer push-to-start switch has 2 terminals.
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore electric dryer models.
I replaced the starter switch, that really didn't need to be replaced, and the thermal fuse, which did. Read more
Dryer won't heat or stops working? A burnt or melted terminal block disrupts power flow. DIY repair in under an hour with video guidance included.
I ordered the parts through AppliancePartsPros.com. They were delivered the next day. I installed them and the dryer works great. Read more
This screw is used to secure the handle end cap to the center of the door. The screw size measures 8-18 x 1/2 inches.
This was actually one of the easiest fixes I’ve done. All that was required was to remove 3 screws to remove the broken part. I used a pair of pliers to remove the moisture sensors from the broken part to the new one. Read more
Screw secures appliance panels and access covers. Replace missing, stripped, or corroded screws to restore tight fit and eliminate rattles or gaps.
After several attempts at Local Hardware stores and Lowe's and Home Depot to find them I called AppiancePartsPros.com. I gave them the model number and what I was looking for and customer service directed me to the part on the Web site. They were extremely helpful and it was very fast and I got the parts the next day. Read more
The Door Handle is an OEM component for Whirlpool dryers. It provides convenient access to load and unload clothes through the dryer door opening.
Causes of a bad door handle can include normal wear and tear over extended use. Repeated clutching and releasing of the handle leads to fatigue of rubberized grip areas and loosening of mechanical connections. Accidental falls or impacts when transporting dry loads of clothes could also damage the handle structure or mounting.
Symptoms of a bad dryer door handle include:
Compatible models also include Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore dryers.
Separated oven door by removing screws. Inserted handle and secured with clips, and reassembledo door with screws provided. In served broiler handle and snappedal into place. Read more
The Whirlpool screw is an OEM replacement part responsible for securing various components or parts on different types of Whirlpool appliances. The screw is designed to provide a secure and reliable fastening connection, ensuring that different parts of the appliance stay in place. It is commonly used in different locations within the appliance, such as the cabinet, panels, or other structural elements. This part fixes the following symptoms:
The Whirlpool screw can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
One day my wife went to bake something and the bake/broil buttons as well as #3, #9, and oven light ceased to work. Local repair guy came by and wanted to charge $500 to fix it....YEAH RIGHT! Did a little homework and found this website, spoke with knowledgable staff who pointed me in the right direction. Took me all of about 20 minutes to install new control panel..everything works perfect...THANKS! p.s. In doing my research come to find Maytag did little to insulate control panel from oven... Read more
Dryer won't power on or has loose power cord connection? This terminal block screw kit secures electrical connections. Easy DIY fix in 15 minutes.
And after replacing the thermal fuse The dryer turned on. Read more
Dryer won't start or run? A worn or broken door strike prevents the latch from engaging properly. Quick 5-minute fix restores safe operation.
I ordered the male and female door latching parts. Read more
Includes screws and wire connectors. For the complete terminal block kit use 279320.
U-type clip nut slides onto sheet metal panels to create threaded anchor points for screws. Replace if broken, missing, or worn during repairs.
I undid the top with a putty knife, took out two screws and took off the front. I replaced the drum rollers and put the new belt on the drum, looped the belt on the idler and then onto the motor pulley. I also put on two new top hold down clips as the old ones broke because they were plastic, the new ones were metal. I took off the back panel and replaced the heating element. The hardest part was cleaning up all of the lint and dirt that had accumulated over the years. It was not difficult,... Read more
This support washer is a flat spacer used within the mechanism to support and separate mating parts, maintaining alignment and smoother movement. Replacing a worn washer helps reduce friction and wear so components operate properly. What it does:
Followed the video- opened the front of the dryer and removed the drum. It was evident that one of the wheels had worn and wasn't turning freely like the other one. The video showed how to remove the roller. Very simple process and now the dryer works just fine. Read more
This console screw secures the control console to the appliance cabinet or top, keeping the panel tight and aligned. Replace a missing or damaged screw to stop panel wobble and rattling and maintain a snug, stable fit. What it does:
THIE REPAIR WAS ON A WHIRLPOOL TOP LOAD WASHING MACHINE At first I suspected the leak was from the pump because I had replaced the pump 2 times over 10 years. This time with the cabinet removed and filling the tub with water, I saw water running down one of the steel support arms that go under the tub, so I was guessing that it was coming from the tub seal. I had to use a jumper wire to bypass the Lid Switch so the water would drain. Several months before I had this issue with the water leaking... Read more
Low-friction bearing ring for smooth drum rotation. Replace when you hear squealing or scraping during cycles. Confirm fit with your model number.
Looked up the part on AppliancesPartsPros.com. Ordered the part. Installed now it works like new. Read more
This 8-18 x 5/8-inch screw secures dryer panels, brackets, and covers. Replace missing or stripped fasteners to restore a tight fit and stability.
I put all pieces that I ordered on the dryer and plugged it in. Read more
This locking nut is used for many purposes on a range of machines including household appliances. This nut is often used for leg leveling for machines. It will help with vibrations from washers and dryers. If the nut is used for this purpose and goes missing or becomes damaged, it could cause the machine to vibrate more and seem louder.Nuts are made from metal and are built to last a long time. However, there can still be issues that arise. In some cases, the nuts might go missing if they become loose and the machine is moved. They could also corrode over time and need to be replaced. The replacement of the nut is typically a fast and simple repair.The nut is a genuine OEM replacement part sourced from the manufacturer. It can work with washers, dryers, and combo machines, and is compatible with models from Whirlpool, Kenmore, Maytag, and Roper. The part is sold individually. Owners may want to have several on hand.
Replaced 2 springs and brackets. Also replace rear legs and front legs and re leveled. Works fine. Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.