Lse806aee Parts

Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.

Genuine Whirlpool part

Washer Outer Tub Seal

4.6 (7)

By: Whirlpool

Part Number: WP211232

This is a rubber gasket seal that fits between the outer tub halves or around the tub ring of a washing machine, creating a watertight seal to prevent leaks during the wash and spin cycles. It compresses between the tub components when they are clamped together. Replace this seal if you notice water leaking from around the outer tub, pooling under the washer, or if the seal appears cracked, hardened, or deformed.

Do-It-Yourself Stories from Customers like You No agitation. Susan B. • Apple Valley , CA • August 09, 2020

This was some repair! My SG1000 stackable is over 30 years old and was purchased second hand. I've replaced many parts in the dryer section, but besides a water inlet, this was my first repair to the washer. All of a sudden it started making a terrible noise and was not agitating the clothes. The spin cycle worked fine. I first replaced the two belts on the bottom, but when I removed the old ones I realized they did not look terribly worn and weren't the cause. Many stories on here indicated... Read more

$55.30

Compare At:: $66.36
You Save:: $11.06

IN STOCK

Ships Monday Guaranteed

Add to Cart

Genuine Lg part

Sheath Heater

By: Lg

Part Number: MEE32902206

This sheath heater is the electric element that delivers radiant heat for the unit's heating cycles, such as grill/broil or convection. Replacing a failed heater restores proper temperature performance and consistent results.

Generates radiant heat when energized to help reach and maintain set temperature
Supports grill/broil or convection functions for browning and even cooking
Common failure signs: no heat in those modes, extended preheat times, uneven results, tripped breaker, or a visibly blistered/broken element
Restores reliable heating performance when the original element is open or shorted

What's included: 1 sheath heater Install notes:

Disconnect power and let components cool before servicing
If servicing a microwave, remember high-voltage components can retain a dangerous charge; discharge the capacitor and consider service if you're not experienced
Handle the element by its brackets; avoid bending the sheath or stressing terminals
Move wires one at a time to the new part and verify element continuity with a multimeter before reassembly

$45.54

Compare At:: $54.19
You Save:: $8.65

IN STOCK

Ships Monday Guaranteed

Add to Cart

Genuine Whirlpool part

Leveling Leg Pad

5.0 (8)

By: Whirlpool

Part Number: WP210684

The Leveling Leg Pad is an OEM replacement part for Whirlpool washing machines. This small but essential component fits beneath the leveling legs, providing stability and preventing the appliance from moving or vibrating excessively during operation. It also protects flooring surfaces from potential scratches or damage.

Symptoms of a bad Leveling Leg Pad include:

Increased vibration or noise during the wash or spin cycle
The washing machine wobbling or becoming unsteady
Visible wear, cracks, or damage to the pad

Causes of a failing Leveling Leg Pad can include wear and tear from prolonged use, exposure to moisture, or excessive weight causing deformation. Replacing worn pads helps maintain the appliance's balance and efficiency.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

For the leveling leg order 22003428.

This part fixes the following symptoms

Shakes and moves

Do-It-Yourself Stories from Customers like You Washer "bucking" while in spin cycle Luis P. • Loveland , CO • June 27, 2017

New leveler pads Read more

$11.78

Compare At:: $13.90
You Save:: $2.12

IN STOCK

Ships Monday Guaranteed

Add to Cart

Genuine Whirlpool part

Washer Water Inlet Hose

4.8 (5)

By: Whirlpool

Part Number: WP213013

Water inlet hose for washers and laundry centers. Connects water supply to fill valve. Replace if cracked, leaking, or worn to prevent floor leaks.

Do-It-Yourself Stories from Customers like You 35 year old Maytag washer/dryer stack unit with a water leak. Paul K. • Naperville , IL • December 24, 2022

I cannot believe this machine still runs. APP has sold me repair parts for this unit now 3 times. First I wanted to replace the old belts. They still worked but was more a preventative thing. Next was a water control valve a few years ago. This time I noticed a leak near the valve again. I decided to buy a new valve and also replace all the rubber hoses that were 35 years old. The repair took about 3 hours. 1.5 to remove the old parts and do a cleaning that was greatly needed. 0.5 hours to... Read more

$41.95

Compare At:: $49.92
You Save:: $7.97

IN STOCK

Ships Monday Guaranteed

Add to Cart

Genuine Whirlpool part

Rubber Foot

5.0 (1)

By: Whirlpool

Part Number: WPY314137

The rubber foot is an OEM replacement part for Whirlpool washing machines. This small but essential component fits beneath the leveling legs, providing stability and preventing the appliance from moving or vibrating excessively during operation. It also protects flooring surfaces from potential scratches or damage.

Symptoms of a bad Leveling Leg Pad include:

Increased vibration or noise during the wash or spin cycle
The washing machine wobbling or becoming unsteady
Visible wear, cracks, or damage to the pad

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

For the leveling leg order W10176519.

Do-It-Yourself Stories from Customers like You Unlevel and shaking moving out of position cracked dryer igniter Steven B. • Grantsville , WV • April 26, 2016

Replaced dried crumbling rubber foot. Cleaned inside and outside of dryer before installing igniter cleared vent hose. Leveled unit installed dryer igniter. Fired it up.Runs Great Now. Read more

$7.95

Compare At:: $9.46
You Save:: $1.51

IN STOCK

Ships Monday Guaranteed

Add to Cart

Genuine Whirlpool part

Washer Agitator Seal Assembly

5.0 (1)

By: Whirlpool

Part Number: WP6-0A57420

Seals the agitator shaft opening to prevent leaks and protect internal components. Replace if you see water leaking from the center post during wash cycles.

Do-It-Yourself Stories from Customers like You Washer would only spin. Byron V. • Bellevue , MI • February 04, 2020

Found the wonderful parts diagrams you most generously share online and a couple of YouTube videos . I determined it should be repairable. In my cast the agitator shaft was frozen (rusted) in place. I was very fortunate to have been able to eventually remove it with the use of a lot of BP penetrating oil and heat. Long and short the replacement parts fit perfectly and the washer is running like new. Special thanks to the online support make my repair possible. Read more

$23.95

Compare At:: $28.50
You Save:: $4.55

IN STOCK

Ships Monday Guaranteed

Add to Cart

Genuine Lg part

Range Main Control Board

By: Lg

Part Number: EBR80595701

Fix a range that won't heat, displays error codes, or has unresponsive controls. This main control board manages power distribution and system logic.

$114.48

Compare At:: $137.38
You Save:: $22.90

IN STOCK

Ships Monday Guaranteed

Add to Cart

Genuine Whirlpool part

Drain Hose

5.0 (7)

By: Whirlpool

Part Number: WP22003410

Size: 90 inches long. To order hose extension use 12001585. To order siphon break use 76660.

Do-It-Yourself Stories from Customers like You General overhaul of a 14 year old machine Todd F. • Wellsburg , WV • January 20, 2016

Model# MAV7257AWW Maytag Atlantis Washing Machine. Repairs were fairly easy along with the videos appliancepartspros offers on their website. Parts also came with instructions on how to install. Other videos were available on You Tube. The only part difficult to install was Thrust bearing kit - make sure when installing to pull down on shaft so washer and e-clip will fit. Another note, you can get a pulley for your replacement motor pulley on eBay and Maytag.com. Just pay close attention to... Read more

$50.57

Compare At:: $60.18
You Save:: $9.61

IN STOCK

Ships Monday Guaranteed

Add to Cart

Genuine Whirlpool part

Washer Outer Tub To Pump Hose

4.7 (11)

By: Whirlpool

Part Number: WPY212989

Internal hose that channels water from the washer's outer tub to the drain pump. Replace if cracked, leaking, or worn to prevent puddles under the machine.

Do-It-Yourself Stories from Customers like You Leaking hose at tub not bad for 32 year old machine Gary W. • Chubuck , ID • December 25, 2016

Removed front of washing machine, loosened clamps, got wet, replaced hose, tightened clamps, tested hose--no leaks--job done. PLEASE, PLEASE put up a description indicating the length of hose, measured along its length, is 15." It will save other folks wondering if they ordered the wrong item. Thank You. Read more

$44.24

Compare At:: $65.49
You Save:: $21.25

IN STOCK

Ships Monday Guaranteed

Add to Cart

Genuine Whirlpool part

Washer Water Injector Sleeve

4.6 (7)

By: Whirlpool

Part Number: WP22213057

Seals the water path at the injector assembly. Replace if you notice leaks during fill cycles or poor water flow. Confirm fit with your model number.

Do-It-Yourself Stories from Customers like You Leaked water during tub fill James M. • Hampton , VA • May 15, 2017

Replaced the Injector valve, nozzle and sleeve-in using new hose clamps Read more

$5.95

Compare At:: $7.14
You Save:: $1.19

IN STOCK

Ships Monday Guaranteed

Add to Cart

Genuine Whirlpool part

Hose Clamp

5.0 (6)

By: Whirlpool

Part Number: WP616099

This hose clamp secures a hose connection to prevent leaks and keep your appliance running smoothly. It provides a tight, reliable hold on the hose fitting so water or air stays contained during operation.

Tightens around a hose and fitting to maintain a secure seal
Helps stop drips, seepage, or loose connections
Common fix when you see moisture around a hose joint
Useful if a clamp is rusted, stretched, or no longer holding tension

What's included: One hose clamp. Install notes:

Unplug power and shut off water (if applicable) before servicing
Note clamp position/orientation before removal
Use appropriate screwdriver or nut driver to tighten evenly
Do not overtighten—ensure a snug, leak-free seal without damaging the hose

This part fixes the following symptoms

Leaking

Do-It-Yourself Stories from Customers like You Water leak Steven K. • New City , NY • August 10, 2018

Took off cover, installed new parts. Read more

$4.60

Compare At:: $5.47
You Save:: $0.87

IN STOCK

Ships Monday Guaranteed

Add to Cart

Genuine Whirlpool part

Washer Injector Fill Hose

5.0 (3)

By: Whirlpool

Part Number: WPY215234

Connects water supply to the dispenser injector in your washer. Replace if cracked, nicked, or leaking. Installs at the top under the lid assembly.

Do-It-Yourself Stories from Customers like You Hole in the injector valve and a nick in the injector fill hose Ray A. • Union Beach , NJ • July 10, 2016

First the parts showed up as promised in 2 days. Injector fill hose wasn't leaking but replaced to be on safe side. Everything went together just like OEM parts. Cost less then having my appliance guy just walk thru the door at $80.00 Read more

$41.95

Compare At:: $49.92
You Save:: $7.97

IN STOCK

Ships Monday Guaranteed

Add to Cart

Genuine Whirlpool part

Screw (#8-18 X 5/8 In.)

4.5 (2)

By: Whirlpool

Part Number: WP98165

This replacement screw secures panels, brackets, and components inside appliances. Replacing a missing or stripped fastener restores a snug, rattle-free fit using the correct #8-18 thread and 5/8-inch length.

Fastens covers, trims, brackets, and internal parts to the cabinet/frame
Used wherever a #8-18 x 5/8 screw is specified
Replace if the original is missing, corroded, stripped, or will not tighten
Symptoms: loose or rattling panels, gaps, or hardware that backs out

What's included: 1 screw (#8-18 x 5/8 in.) Installation notes:

Disconnect power; shut off gas/water before servicing
Match thread and length; start by hand to avoid cross-threading
Use the correct driver bit and tighten snugly—do not overtighten
Inspect and replace damaged clips or tabs before securing

Do-It-Yourself Stories from Customers like You Missing parts Barry E. • Long Beach , WA • July 20, 2019

Replace Read more

$7.56

Compare At:: $8.83
You Save:: $1.27

IN STOCK

Ships Monday Guaranteed

Add to Cart

Genuine Ge part

Appliance Mounting Screw

4.7 (3)

By: Ge

Part Number: WB1X1130

Replacement screw for securing panels, brackets, and internal components. Needed when original hardware is stripped, missing, or damaged during repairs.

Do-It-Yourself Stories from Customers like You Broken door hinge on a ge wall mount double oven Cheryl A. • Mckinney , TX • June 18, 2018

We replaced the broken door hinge. Read more

$14.58

IN STOCK

Ships Monday Guaranteed

Add to Cart

Genuine Whirlpool part

Hose Clamp

5.0 (6)

By: Whirlpool

Part Number: WP489503

This hose clamp secures a rubber or plastic hose to its fitting to maintain a tight, leak-resistant seal. Replace a worn or missing clamp to stop drips and keep appliance water connections secure.

Fastens a hose to a barb or port to prevent leaks
Helps keep hoses from slipping off due to vibration or pressure
Restores proper sealing when a clamp is rusted, bent, or stripped
Common symptoms: water dripping at a hose joint, loose hose connection, or a clamp that won't tighten

What's included: 1 hose clamp Install notes:

Disconnect power and shut off the water supply before servicing
Place a towel to catch residual water when removing hoses
Position the clamp just behind the hose barb/bead and secure with the appropriate tool
Restore water and power, then run a quick check for leaks at the connection

This part fixes the following symptoms

Leaking

Do-It-Yourself Stories from Customers like You Leaking bleach tube Mike C. • Willow Grove , PA • May 21, 2017

Replaced the tube and the clamp Read more

$7.49

Compare At:: $8.91
You Save:: $1.42

IN STOCK

Ships Monday Guaranteed

Add to Cart

Genuine Whirlpool part

Dryer Terminal Insulator Assembly

3.8 (6)

By: Whirlpool

Part Number: Y304596

Insulates and supports electrical connections through the dryer chassis. Replace if cracked, heat-damaged, or broken to prevent shorts and restore safety.

Do-It-Yourself Stories from Customers like You Our 35 year old maytag dryer stopped heating Chris P. • Victor , NY • August 15, 2015

I ordered all the parts necessary to replace the heating element and thermostat on a Sunday night. Appliance Parts Pros shipped on Monday AM and I received them on Wednesday. It took me 45 minutes to disassemble the dryer, replace the parts and have the dryer working again. It should be good for another 35 years which should cover me for my needs. Thanks again to Appliance Parts Pros for having the best service and always the correct parts. I am a huge fan of your company as you never... Read more

$26.95

Compare At:: $32.34
You Save:: $5.39

IN STOCK

Ships Monday Guaranteed

Add to Cart

Need help finding dishwasher parts?

Need help finding dishwasher parts?

Need help finding dishwasher parts?

Lse806aee Parts

Washer Outer Tub Seal

Sheath Heater

Leveling Leg Pad

Washer Water Inlet Hose

Rubber Foot

Washer Agitator Seal Assembly

Range Main Control Board

Drain Hose

Washer Outer Tub To Pump Hose

Washer Water Injector Sleeve

Hose Clamp

Washer Injector Fill Hose

Screw (#8-18 X 5/8 In.)

Appliance Mounting Screw

Hose Clamp

Dryer Terminal Insulator Assembly

Need help finding dishwasher parts?

Need help finding dishwasher parts?

Need help finding dishwasher parts?

Lse806aee Parts

We respect your privacy

Manage consent preferences